How to make your own tackifier table tennis rubber ?

It's best not to use anything, if there is a lot of dust, you can gently wipe it off with a sponge, put the racket into the racket cover to avoid light after playing, and you can also paste plastic wrap.

Isolate the air. In this way, the rubber can be used for two years. Don't wash with water, if you wash with water, it will be wasted in three months, and the tackifier will hurt the rubber to a certain extent, so it's best not to use it.

The best thing is to pay attention to protect the rubber and prolong the service life.

The best cleaning method is: use a sponge for women to wipe powder (better than the special cleaning cotton for table tennis sold), wet water (you can use water, the effect is the same as the special cleaning agent bought for more than ten yuan), and then wring it out as much as possible, wipe off the dust on the surface of the rubber, dry it and put it in the racket case. Note:

Don't put a protective film! Many people think that sticking a protective film can protect the rubber, which is a misunderstanding, but it will actually hurt the rubber! Repeated attachment and tearing off will reduce the adhesion of the rubber surface.

You can only put on the protective film when you don't use it for a long time, and don't put it on if you wear it often.

In short, as long as you pay attention to keeping the playing environment clean and clean the rubber after playing, then a piece of Crazy 3 will be no problem for 1 year.

The following is the formula of table tennis paddle rubber cleaner:

Materials: 11 cup warm water.

2.1 tbsp white vinegar.

3.1 tablespoon alcohol.

4.1 tablespoon liquid laundry soap.

5.1 spray bottle.

Steps:1Pour 1 cup of warm water into a spray bottle.

2.Add 1 tablespoon of white vinegar and 1 tablespoon of alcohol.

3.Add 1 tablespoon of liquid laundry soap.

4.Shake the spray bottle well so that all the ingredients are mixed together.

5.Place the table tennis racket on a clean surface.

6.Use a damp sponge to wipe the dust off the rubber.

7.Wait for the water stains on the rubber to dry, spray some detergent and use a sponge to smooth it out.

Summary. Pro, table tennis racket tackifier preparation: 1 Remove the set of rubber and wash it, choose a piece of kraft paper and cut it into a circle larger than the set of rubber, put it on the rubber, and then heat it with an electric iron, and look through it from time to time, and wait for the rubber to become bright and sticky.

2 Note: Be sure to use kraft paper, other paper will stick to the rubber. Heat only when it is sufficient.

At first, I made the rubber too sticky, like a sticky mouse board, and I couldn't shake off the ball. 3. Problem treatment: After the same treatment, the rubber and sponge will mostly be disconnected, and the rubber will be deformed after heating, and it is difficult to stick to it again.

Now tell my friends a way to glue the rubber as flat as the new set of glue: find two glass plates or plexiglass plates that are larger than the set of glue, and use paper glue or rice soup to stick the rubber sponge on the glass plate respectively, pay attention to be sure to stick flat and clean the air, which is the key to determining the final quality!! Then press on a heavy object and dry it thoroughly.

The final job is simple: brush the glue on the rubber particles and sponge, buckle it after 30 minutes, roll it a few times, and press the heavy object to dry. After drying, remove the glass plate with water and you're done.

Homemade table tennis racket tackifier.

Pro, table tennis racket tackifier preparation: 1 Remove the set of rubber and wash it, choose a piece of kraft paper and cut it into a circle larger than the set of rubber, put it on the rubber, and then heat it with an electric iron, and look through it from time to time, and wait for the rubber to become bright and sticky. 2 Note:

Be sure to use kraft paper, the rest of the paper will stick to the rubber. Heat only when it is sufficient. At first, I made the rubber too sticky, like a sticky mouse board, and I couldn't shake off the ball.

3. Problem treatment: After the same treatment, the rubber and sponge will mostly be disconnected, and the rubber will be deformed after heating, and it is difficult to stick to it again. Now tell my friends a way to glue the rubber as flat as a new one:

Find two glass plates or plexiglass plates that are larger than the set of glue, and stick the rubber sponge on the glass plate with paper glue or rice soup respectively, pay attention to be sure to stick flat and clean the air, which is the key to determining the final quality!! Then press on a heavy object and dry it thoroughly. The final job is simple :

Brush the glue on the rubber particles and sponge, buckle it after 30 minutes, roll it a few times, and press the heavy object to dry. After drying, remove the glass plate with water and you're done.

Thank you. Dear, do you have any other questions? If not, please give a thumbs up, thank you very much!

The tack enhancer for table tennis racket cleaning is composed of alcohol, solvent and water.

Its functions: 1. Effectively reduce the adverse effects of air, light and dust on the viscosity of the rubber surface;

2. Make the rubber can maintain a high viscosity for a long time to prevent premature aging of the rubber;

3. Extend the life of the rubber.

The tack promoter is also good for table tennis racket cleaning, the viscosity is significantly enhanced after use, and the rubber becomes very clean, but the viscosity after cleaning cannot reach the effect of the original rubber.

The role of the tackifier for table tennis racket cleaning:

Effectively reduce the adverse effects of air, light and dust on the adhesion of the rubber surface;

It enables the rubber to maintain a high viscosity state for a long time to prevent premature aging of the rubber sheet;

Extend the life of the rubber.

Table tennis racket cleaning tackifier is also better, the viscosity is significantly enhanced after use, and the rubber has become very clean, although the viscosity after cleaning can not reach the effect of the original rubber, but it is still a good helper for ordinary paddle protection!

After a period of use, the adhesive sleeve has no stickiness, this is because the cover rubber layer on the surface of the adhesive sleeve is in too much contact with the air or encounters tap water (containing hypochlorous acid, strong oxidant) is oxidized, mainly caused by not doing a good job of protection, and the film is not attached after playing, or washed with tap water.

In order to prevent the sleeve from losing its tack too quickly, a cleaning tackifier can be used, which is said to maintain the adhesive of the lid. Personally, I feel that it is just a temporary delay in the loss of stickiness.

Usually, the cleaning tackifier is sprayed onto the adhesive surface, wiped clean with a sponge, and then the adhesive film is applied.

Hehe, as for the effect, some say it's good, some say it's bad.