-
Hello, according to your description, if you install a reversing image, it is still necessary to install this. After installing a reversing camera, you can observe the distance behind when reversing. This way it is safer to reverse. It is recommended that you install a reversing camera.
-
The reversing camera is a very practical configuration and is recommended. If you drive normally and reverse, as long as you look at the left and right rearview mirrors on both sides, plus the reversing image, it is enough to reverse the car close enough.
-
Of course, it is necessary, the reversing image is very important, and it is still a bit difficult to rely on the reversing radar alone.
-
Cruze reversing camera: If the economic conditions allow, you can install one, which is more convenient, but it is better to be careful when driving, my Cruze has not installed a reversing camera. Personal opinions are for informational purposes only.
-
Hello reversing video, I think it is necessary to install it in the car, which can reduce the danger and increase the safety rate of reversing, and install it better.
-
The reversing camera is still more useful. At the very least, when reversing, you can also see the objects behind you very clearly and intuitively.
-
Hello, the function of reversing image is very good, after all, watching reversing can be more intuitive, and safer.
-
This depends on your specific needs, and it is recommended to install a reversing image if you are a novice, which can be a good reversing.
-
Hello, this personal feeling that if there is a reversing radar, there is no need to install a reversing image, it depends on your technology.
-
Hello, this one is honest, if you just want to be more convenient when reversing, then this reversing radar is more cost-effective.
-
1.Take out the license plate light and thread the wiring harness through the license plate light. 2.
Screw the pried light bulb onto the camera. 3.Among the two jumpers of the camera, the red one is connected to the positive pole of the lamp, and the black one is connected to the negative pole; The camera's signal cable is connected to one end of the signal extension cable.
4.Extension and reversing cables are connected to the instrument panel via trunk power cords and door sill jujube pads. 5.
The signal extension cable is connected to the display. 6.Restore power to the depleted battery.
Reversing image is also known as parking assistance system, or reversing vision system, vehicle monitoring system, etc. The system is widely used in various large, medium and small vehicle reversing or driving safety assistance fields.
The reversing camera is mounted at the rear of the vehicle with a far-infrared wide-angle camera, and obstacles at the rear of the vehicle can be seen through the in-vehicle display. Even at night, infrared light can clearly see it. Its function is to allow the driver to see the situation behind the car on the display when reversing, so as to avoid accidents due to not being able to see the situation behind the car.
There will be a big blind spot when driving forward, let alone reversing, except for the rearview mirror, you can't see it basically. But the stool bridge stupid rearview mirror has a big blind spot that is not visible near the vehicle. At this time, if the rearview mirror of the car can be displayed on the central control screen, the road condition information directly behind the car can be clearly seen when reversing, and it is more convenient to reverse.
Millions of car purchase subsidies.
-
Reasons why the Chevrolet Cruze reversing image does not show:
1. Check whether the line is connected.
2. Look at whether your reversing rear view trigger line is connected.
4. Remove your camera and connect it to someone else's navigation to check whether the camera is broken.
Possible reasons why the Chevrolet Cruze reversing image does not respond:
1. Problems with display settings. There are still many such problems,Generally, there is a camera switch control in the settings of the display,The switch can be adjusted to"on"。
2. The camera is malfunctioning. Replace the reversing camera.
3. Line problems. One of the highest failure rates. Because the wiring harness of the reversing image is pulled from the instrument panel to the trunk, the wiring is long, and it is likely that the wiring harness or plug in a certain place is not in good contact, and it needs to be carefully checked.
Chevrolet Cruze reversing image does not respond to the vehicle installed after the reversing image, mainly the problem of the product and the problem of construction, in order to avoid hidden dangers in the future, the owner who wants to install the reversing image must buy a good product, and find a professional maintenance station to operate, otherwise if there is a problem with the line, it is still very troublesome to investigate.
-
Could it be that the reversing image requires too much power, that is, there may be a short circuit inside the reversing image.
-
There are several reasons for this:
1. After installing the reversing camera, the output voltage is not enough, resulting in instability, and the voltage is measured.
2. The line is loose, resulting in poor contact, check the line.
3. There is no problem with the above two points, that is, the product quality problem, try to replace the product.
The steps explain the possible causes of the problem separately, and the results have been explained later, so please check them carefully.
-
The camera and the impact screen wiring are not done well, and they have to be redone.
I still remember that 10 years ago, it was already very good to have a reversing sensor on the car, and the reversing image was a configuration that only luxury cars would have. But now when buying a car, the reversing image has almost become the standard, even if there is no reversing image on some low-profile models, the owner will also install one after buying it back, anyway, this thing is very cheap, a few hundred yuan can also be installed for thousands of yuan. The emergence of reversing images has indeed brought great convenience to drivers and friends, especially some novice friends, who no longer have to worry about hitting the rear vehicle when reversing. >>>More
The phenomenon of black screen in the reversing image is likely to be due to poor line contact, and it is necessary to check the wiring between the line and the vehicle installation in time to see if there is a false connection. If there is, it will naturally lead to the situation that the reversing image is not working at any time, and even a direct black screen is possible, at this time, as long as the virtual part is connected well. Of course, it may also be because the power cord is aging, you can try to replace it with a new power cord, if the black screen can be solved, it means that there is indeed a problem with the power cord.
Installation steps: First, remove the power supply cable at the vehicle battery, and place the removed wire away from the electrodes to prevent the power supply from being accidentally connected. >>>More
Installing the Bowen Bowon reversing camera under normal circumstances, there are auxiliary lighting of license plate lights, small lights, and reversing lights, so it is rare that there will be no light source at all. The chip's camera is self-sensitive, which means that the more sufficient the light source, the better the effect of the chip's self-sensitivity adjustment, and the better the clarity will naturally be. If you're in total darkness and you can't see your fingers, even a multi-million night vision camera won't be what you'd expect. >>>More
Hello, the individual reversing image kit** is relatively cheap, and it is sold on all major online platforms. >>>More