Does a hole in the wall belong to building How much does it cost to make a hole in the wall?

Updated on home 2024-07-14
18 answers
  1. Anonymous users2024-02-12

    If you look at how big the scope of the hole is, most of the impressions may be the air conditioning hole, as well as the installation of range hood ventilation ducts, and these are carried out on the wall of your own house, not belonging to the building, within the scope of normal decoration, so there should be no problem with making holes in your own wall, and there is no need to notify the property, which belongs to the internal affairs of your own home.

  2. Anonymous users2024-02-11

    Punching holes in the wall is also a very small project, whether it is opening the door or making holes in the wall.

  3. Anonymous users2024-02-10

    Holes in the walls are not built! He belongs to the demolition and reform! This depends on your construction situation!

  4. Anonymous users2024-02-09

    Indoor wall repair problem: the home decoration is painted with latex paint, today the wall has a few holes, rhinestones, the wall is very wet and dirty, how to repair.

    It's very simple, buy back the original paint like you brush latex paint, buy environmentally friendly, then buy buckets of putty powder (also called double fly powder) and putty powder glue, adjust the putty powder and glue, brush to the wall, wait for dry and then brush, then buy a fine sandpaper, brush the putty powder and polish it flat, and then brush and polish again, repeat a few times, and wait until it is completely dry and the wall is flat, just buy a brush to brush latex paint! 1. Generally, talcum powder is used to add glue, in fact, you go to the place where you buy to buy the adjusted glue to use. 2. Look at the big hole, if you want to look good, you still have to find some sand plaster to smooth it, and then put putty, and use waste cardboard or foam to block it with artwork, and you can't see it on the ash.

    When to decorate, if you want to repair the wall to dry and then repair, you said that something like paper should be latex paint after the film, up is the bottom layer of putty powder to be pulverized by water, such as you want to deal with it, after the wall is dry, the blistering place is cleaned with the product, now the market is used to directly add water putty powder, no need to add glue, you said that the deeper holes, with putty powder can also be repaired, but in the depths all greasy.

  5. Anonymous users2024-02-08

    Punching holes in concrete is not the same as punching holes in the brick wall, generally about 100 air conditioning holes are played on the concrete, there are thirty or fifty brick walls, and the beams will be higher.

    Related Notes:打hole, a Chinese word, pinyin dǎ dòng, to dig a hole with utensils.

    Nie Yun's crossbow "Ji's General Cutting Away": Ran Youcheng is trying to make a hole all day long, and as an official, he is trying to make a fortune.

  6. Anonymous users2024-02-07

    Line holes, water is charged 20 yuan, dry beating is 40 yuan, a range hood is 160 diameter of water 160 diameter charge 120 yuan, water 110 diameter 100 yuan, dry need to add 40 yuan.

    The water of the water heater is 70 yuan a piece.

    The air conditioner hole water is 30 yuan a piece, and the dry hole water is 40 yuan a piece.

  7. Anonymous users2024-02-06

    It's better to buy a percussion drill yourself, I will spend 78 yuan to buy it myself, super value, share and recommend Yongkang Gomez Industry and Trade **** products, search for it yourself!

  8. Anonymous users2024-02-05

    I did the installation of water and electricity, and the hole of the hood was about 50, so the small hole didn't matter, and it was dry with it.

  9. Anonymous users2024-02-04

    The load-bearing beams of the concrete are not allowed to be eye-catching, and you have to act very heavily.

  10. Anonymous users2024-02-03

    At least 150 yuan for a hole, and the larger one is counted separately.

  11. Anonymous users2024-02-02

    In the position of the beam hit is 40, and the ordinary wall is 20

  12. Anonymous users2024-02-01

    Use a drill bit to make holes.

    The walls below the punching position and the ground within the punching range are all covered with new plastic film to prevent water and dust from sticking to the walls and floors when the rhinestones are punched. It is best to paste or lay a layer of paper (similar to a cardboard box) on the wall and ground in the work area to prevent the block material from falling and hurting the ground or sticking to the wall.

    The choice of drill bit depends on the size of the expansion screw. The diameter of the hole should be smaller than the diameter of the drill bit. The diameter of the drill bit is too large, and the expansion screw falls directly into the hole, which cannot play a fixed role.

    When drilling, be sure to keep it perpendicular to the drilling surface, and hold the electric drill tightly with both hands to ensure the stability of the electric drill. Use a pencil to draw the position of the drilled hole, choose the appropriate expansion screw, the expansion screw is too small and falls directly into the hole, which cannot play a fixed role.

  13. Anonymous users2024-01-31

    How to make a hole in the wall quickly.

  14. Anonymous users2024-01-30

    Punch the hole with an electric hammer and screw the expansion screw will be very strong.

  15. Anonymous users2024-01-29

    If it is a tile, make small holes in it and make a mark with a pen.

    In order to prevent the tile from falling dust, you can mark the transparent tape to prevent slipping and dust.

    The large hole has a variety of drill bits.

    If you want to drive a two-meter one, drive a forklift to hit it, trim the edges with a small hammer, and touch the seams with putty.

    No matter how big the hole is, it can only be done with explosives (which is very risky).

  16. Anonymous users2024-01-28

    Rhinestones! It's easy.

  17. Anonymous users2024-01-27

    If the hole in the wall is not particularly large, it can be repaired with glue and plaster powder. If the hole in the wall is particularly large, it is necessary to put gravel and broken bricks in the cave first, and then use cement mortar to repair the surface of its material, and then use cement mortar to repair its surface. And it is not allowed to make gravel and broken bricks leak outside, which will affect the overall appearance.

    Then use gypsum powder and putty powder to level the wall, which will make the wall smoother.

    Relevant information: 1. If the indoor wall is damaged, you must first look at the damaged area, if the damage is particularly serious, you should determine how to deal with it according to its difficulty. If the damage is not very serious, the relevant materials should be prepared before repairing.

    2. If there is a crack on the wall, use a shovel to remove the wall about 10 cm around the crack, expose its substrate, and then check why it cracks. If there are cracks in the substrate of the wall, the cracks should be repaired with caulking plaster, and the putty can be scraped after the plaster hardens, and the latex paint must be brushed.

    3. If there is a phenomenon of mildew on the wall, you should use a damp cloth to dip some bleach water, and then wipe the wall with mildew, so that you can wipe the mildew clean. It can also disinfect walls, but this method can only be used on white walls.

  18. Anonymous users2024-01-26

    The holes in the walls of the house need to be filled with cement grout, and when they are filled to a distance of 2 or 3 mm from the wall, they are filled with putty paste, and when the putty paste is filled to the same state as the wall, it is sandpapered and smoothed, and the latex paint is painted in line with the original wall.

    1. For the small holes on the wall, it is necessary to use the wall paste for construction, fill in a small amount of time many times, fill the surface level, and then use sandpaper to polish off the protruding position after it is naturally dry, and the wall paste should be pure white.

    2. When the wall needs to be punched, it is necessary to calculate accurately and then use a drill bit to operate to avoid too many holes affecting the overall effect.

    3. When there are large holes in the wall, especially the holes installed by air conditioners, the holes should be pasted with gauze after filling, and then the gauze should be sealed with putty paste to prevent cracks from being filled tightly.

    4. Pay attention to the strength and angle and the use of tools when punching, use spiral drill bits for cement walls and cross bits for ceramic tile walls.

    5. When repairing the hole in the wall, it is necessary to pay attention to the smoothness of the hole, and the flat hole can be better filled, so it is also necessary to use sandpaper for polishing after filling.

Related questions
5 answers2024-07-14

As the largest space in the home, the wall is often overlooked. When you can't put things in your home, do you think about making good use of the wall? The wall can actually be installed better than you think! >>>More

24 answers2024-07-14

You go to the bathroom shop and look at the shelves that can be sucked up to the wall.

23 answers2024-07-14

Here are some suggested ways to deal with hearing rats burrowing in the wall: >>>More

18 answers2024-07-14

I want to hang a picture frame but I don't want to put nails in the white wall. >>>More

21 answers2024-07-14

First of all, they are responsible, and they have the right to require you to restore the wall to its original state, because the load-bearing wall is used to maintain safety, and the removal of the load-bearing wall and the destruction of the safety structure may cause the wall to collapse. The owner or user of the house (hereinafter referred to as the renovation applicant) must put forward the relevant design plan, submitted to the municipal real estate administrative department for structural safety approval First: open the door, open the window, open the hole, and dismantle the wall. >>>More