If the bathroom is leaking, do it waterproof directly on the original floor tiles, and then turn it

It's not that you can't, but it's not recommended. Because the ground will be too high, if there is water, you will go to the living room. Bathroom waterproofing, especially the shower area to do waterproofing to do 1.8 meters, other places can be 30.

And to find out where the water leakage is, if the waterproof on the floor is not good to do water, you can do waterproofing directly on the original bricks, and then lay the floor is OK, the effect is like this, but there is a point to pay attention to will affect the floor height of the bathroom, because in this case, the height is about 80 to 100 mm.

This can be done to be waterproof, but the floor of the bathroom may be raised and the living room may be flooded.

No, you cannot. Because the most direct consequence of waterproofing directly on the original ground is to raise the ground, and the door must be scrapped and re-customized. Doors that were previously standard may now need to be individually customized.

On the other hand, it is meaningless to do waterproofing on the surface of the original tiles, and the main leakage point is the perennial water seepage of the joints of the resignation, and the edge of the floor drain and tile joints. Another is the reason for the exception of pipes under the floor. Secondly, waterproofing is not only the wall around the ground, but also the wall waterproof half a meter to 2 meters high according to different positions, the wall near the door can be lower, and the wall under the shower is more waterproof.

At the very least, the original floor tiles and wall tiles must be knocked out.

If the bathroom is leaking, you can directly do waterproofing on the surface of the tile, prepare 20 catties of tap water, and pour the waterproof fine seam agent into the bucket, and the specific operation steps are as follows:

1. Prepare 20 catties of tap water.

2. Pour waterproof fine seam agent into the bucket.

3. Stir the waterproof fine seam agent with the water in the bucket evenly.

4. After stirring well, pour the liquid on the bathroom floor.

5. Use a broom.

Sweep the adjusted waterproof seam to every corner of the bathroom.

6. After waiting for an hour, use a shovel to scoop up the solidified waterproof fine seam agent.

7. Clean up the solidified waterproof seam agent.

8. The waterproof fine joint agent penetrates into the gap of the tile and solidifies after mixing with the sediment, which will play the role of waterproofing, and the operation is completed.

Leakage in the bathroom, we generally don't want to remove the tiles to redo the waterproofing, so what measures can be taken?

Treat the roots of restroom pipes as well as walls.

First of all, the root of the pipe and the root of the wall in the bathroom should be cleaned and kept dry.

For particularly small gaps, it is personally recommended to apply glass glue directly. For example, the root of the toilet drain pipe and the part of the toilet that comes into contact with the floor can be sealed with glass glue. In the same way, the circumference of the floor drain can also be sealed with glass tape.

The roots of the wall can also be sealed with glass glue.

Let the glass glue solidify naturally before testing the water. Generally speaking, wait until a day or so before you can test the water again. At this time, you can basically determine whether this part will leak or not.

Deal with the gaps in the tiles.

For dealing with the gaps of ceramic tiles, I personally recommend two methods to everyone. The first method is to make beautiful seams on the tile gaps; The second method is to pour waterproof glue directly into the gaps of the tiles. The processing steps are as follows:

First of all, we also need to clean the inside of the tile gaps. Generally, a thin blade is used to slide back and forth, after which the sand is removed and scrubbed clean.

Pour beautiful seam glue or glue waterproof glue into the gap. When operating, it is necessary to ensure that the upper surface of the glue is higher than the surface of the tile, so as to ensure that the joint agent or waterproof adhesive can be higher than the ground after drying.

Clean up and do a closed water test. At this time, this part can be cleaned and a water storage test can be done to judge whether the repair is qualified.

Tips: When making waterproofing for the bathroom, we must focus on waterproofing all the roots, including the roots of the pipe wall. Generally, the waterproof brush should be made into an arc shape, so that it can effectively play the role of waterproofing.

The wall tiles or floor tiles paved in our bathroom must be paved with seams. In this way, the gap can be sealed. Do not take seamless paving, because seamless paving can not achieve the sealing of tile gaps, and it is difficult to deal with subsequent water leakage.

To do waterproofing, you need to do it on the front of the water.

Dig excellent permeable crystalline waterproof, you can do it yourself.

If the cement surface is waterproofed, use a super permeable waterproof guard to do waterproofing (if there are cracks, gaps and potholes on the cement surface, fill the complete with Meiding porcelain glue and then do waterproofing).

For the tile surface, first check whether the filling of the tile gap is complete (if the filling of the tile gap is incomplete, fill it with Meiding porcelain glue, and then use a stone tile waterproof guard to do waterproofing).

Exterior wall paint can be made waterproof with transparent waterproof repair adhesive.

The product will penetrate into the base layer and make the base layer waterproof. The product is recommended to be constructed in a dry place, the drier the base surface, the deeper the product can penetrate, if the base surface is full of moisture, high density, the material can not penetrate well. Regarding the principle of waterproof plugging, the source of water leakage is not blocked, and the water will only continue to penetrate into the wall, which will exist inside the wall for a long time, and will leak out from other parts of the wall when the water reaches a certain level.

The problem cannot be solved, and only by spraying waterproofing agent on the outside of the roof or exterior wall so that the water cannot penetrate into the wall and flow away can the problem be completely solved.

Hello, I have seen your question and am sorting out the answer, please wait a while

Penetrate into the cracks of the tiles, infiltrate and crystallize to form a stable waterproof layer, the previous method is to dig the floor and pry the tiles to redo the waterproof layer. If you don't want to bother, there is a kind of CPC leak inhibitor, just apply the tile gaps directly, and solve the problem permanently and easily.

Or you have to knock out the original bricks and do them again. Tile waterproof materials for bathroom leakage should be carefully selected, first of all, we must find a direct brush tile waterproof paint coating to wear-resistant, blister-resistant, corrosion-resistant function, directly use bathroom tiles to do waterproof bricks, or knock off and re-do, the surface of the tile is waterproof, must be done before the decoration of the ground waterproof.

The previous method was to dig the floor and pry the tiles to re-do the waterproofing layer. The method you're talking about now is even more distant.

The version of the spectrum can't solve the problem of power at all.

If you don't want to bother, permanently and easily solve the problem, there is a kind of CPC leak-proof agent, just apply the tile gaps directly, this thing is penetrated into the tile gaps, and the penetration crystals form a stable waterproof layer. You're lucky to have me answer this question. Otherwise, you'll take a lot of detours.

CPC leak preventer. You can go shopping.

No, the tiles have to be knocked off and re-painted a few more times to be waterproof.

Pharyngeal leakage must be a leak of the waterproof layer, so under normal circumstances, the floor tiles must be smashed and re-waterproofed.

Not necessarily. There is no need to smash the floor tiles to install the open pipe, as long as you install another set of water pipes on the side of the wall, but the effect of this installation is not good-looking, but it does not affect the use, and it is convenient to maintain.

In this way, it is necessary to find the cause and location of the water leakage and then deal with the symptoms, if the water leakage is in it, it will be smashed.

Not necessarily, you can find a professional to carry out the construction.

According to the specific situation, generally speaking, if it is water seepage caused by the damage of the waterproof layer, in fact, it is very simple to solve it, as long as you buy some anti-permeability waterproofing agent, pour it on the drip and river surface after the water according to the instructions, wait until the waterproofing agent dries naturally, and wait until 24 hours to clean up the solid waterproofing agent on the tile.

Construction method: Buy a permeable waterproofing agent, pour it on the floor after mixing with water, spray it on the wall, and brush it on pipe joints, tile gaps, floor drains, etc. Wait for the penetrating waterproofing agent to dry naturally, and after 24 hours, clean the jelly-like waterproofing agent from the tiles.

Principle: Permeable waterproofing agent is to follow the flow of water to the damaged part of the waterproof layer, and use its strong penetration ability to cover the nearby floor slab. After the waterproofing agent dries, it automatically forms a waterproof membrane. This membrane can block the broken waterproof layer.

Do not smash the floor tiles to judge the severity of the bathroom leakage, is a slight water leakage, then the bathroom does not smash the tile with waterproof coating material is reliable, after all, the waterproof material that can avoid smashing the bricks can prevent slight leakage in the bathroom, and can also play a certain waterproof protection effect. It will not destroy the original decoration either. It is enough to use waterproof leak repair paint.

If the leakage in the bathroom is more serious, the problem cannot be solved without smashing the tiles, and the pipes need to be knocked open to repair the pipes.

Not necessarily, it depends on the situation.

1. If the leakage point is in the floor drain range, no.

It is very difficult to solve this problem when you knock on tiles. The advantage of not being exclusive is that you only need to knock off the tiles within the scope of the floor drain and re-do the waterproofing and then paving, without knocking them all.

2. If it is not just the leakage of the floor drain range, it is necessary to knock off all the floor tiles and re-do waterproofing, because there is no good way to judge the specific leakage point in **, in case it is repaired and the leakage has to be knocked on again, it will be much more troublesome.

3. If it is possible to determine the leakage point and the leakage point can be completely excluded within the scope of the floor drain. You can try it by brushing the tiles in this area with a clear waterproof paint. Of course, try to keep the area as dry as possible.

Many times we do not understand the knowledge of decoration, so the floor tiles will leak the phenomenon, if not timely repair will bring great trouble to themselves and others, at this time people want to repair quickly, but do not know that the floor tiles can be waterproof? And what is the method of leak repair? Let's learn together.

Many times we do not understand the knowledge of decoration, so the floor tiles will leak the phenomenon, if not timely repair will bring great trouble to themselves and others, at this time people want to repair quickly, but do not know that the floor tiles can be waterproof? And what is the method of leak repair? Let's learn together.

Can the floor tiles be waterproofed?

Of course, you can use waterproofing agent, but you can spray it with a nozzle when you use it, or you can use a brush to brush it, and paint it while spraying, so that the waterproofing agent is evenly distributed on the treated surface without omission, and it will fully penetrate into the treated surface to have a good waterproof effect.

How to repair floor tile leakage?

1. Floor tile leakage maintenance method - clean the maintenance surface: empty the debris on the maintenance surface, clean the dust, oil, and water on the surface, and keep the surface dry.

2. Floor tile leakage maintenance method - clean up the tile gaps: clean up the unstrong fillers in the tile joints, remember: do not deliberately buckle the brick joints, as long as the unstrong fillers can be cleaned out;

3. Floor tile leakage maintenance method - spraying waterproofing agent: spraying penetrating waterproofing agent in cement parts such as tile surface, tile joint, wall joint, pipe root, etc., must be sprayed evenly;

4. Floor tile leakage maintenance method - use caulking paste to fill the joint; After the waterproofing agent is dry, fill the tile joints, pipe roots, damaged and defective parts with caulk. This includes the crevices of the wall tiles that can be drenched with water.

5. Floor tile leakage maintenance method - plastic steel mud for waterproof edge: plastic steel mud is used for waterproof edge at the connection between the ground and the wall and large gaps; Around the root of the pipe, around the floor drain, tile damage, defects, thresholds and other weak links, use plastic steel mud to make waterproof edge banding, firm and tight bonding.

6. Floor tile leakage maintenance method - stop water and wait for drying: after the waterproof construction is completed, the construction part can not be drenched within 48 hours. Wait for the caulking plaster to dry before using water.

Summary: You are already clear about whether the floor tiles can be waterproof, as long as you want to do it, there is nothing you can't, it is important to know the maintenance method when there is leakage, so as to solve the trouble in time, I hope my introduction above can help you.