If the bathroom wants water to flow into the floor drain quickly, how should the slope be adjusted?

Only shovel off the tiles on the ground, and then re-pave the floor tiles, shovel off the floor tiles at the same time, try not to destroy the waterproof layer, according to the slope of the re-paving floor tiles, if the shovel off the floor tiles, the waterproof layer is damaged, re-do the waterproof to make a water retaining strip, in the shower partition, after the water retaining strip is fixed, in the shower room with 80 cm floor tiles to pump on the 5 mm interval small seam non-slip, and then paved in the shower room, but let the surrounding line into a circle of 10 cm sink, dig out and re-pavement. This is the reason why the masonry level is not played, and he has to be responsible for repaving.

If the slope is not much different, you can consider cutting the diversion groove, which is a technical job, and ordinary workers can't do it, so it's better to find a good bricklayer to do it.

This has to be re-bricked. A qualified mason master, the wall tiles will be brick joints vertical, flat, the size of the gap is uniform, when laying balcony bathroom floor tiles, there will be a little slope, and the floor drain is about centimeters lower than the brick surface. If our ground error is very large, then I personally recommend that you do not use the thin paste method, but use the traditional cement mortar wet paste method.

The separation of dry and wet can isolate the lack of rain in the bathroom, and the two areas do not interfere with each other, which is conducive to improving the humidity and cleanliness of the bathroom; For smaller toilets, it is basically impossible to separate dry and wet, otherwise, it can only be called thick paste method or traditional paste method. Tile adhesive was originally developed for the thin paste construction process, but now whether it is according to the traditional or thin paste construction, tile adhesive is used. When you do the bathroom, you must do waterproofing, and when you do waterproof protection, you can first do a thin layer to find the slope, and then make a thin tile according to the slope!

If the worker's craftsmanship is very good, you can also find the slope with thin paste, in recent years, with the upgrading of decoration experience, a technical change for some decoration criticism. Commercial houses that were renovated in the past ten years, whether on the first floor or the top floor.

The penetration rate on the <> surface is particularly high, but some inferior floor drains are mainly based on 201 materials, which are generally about 20 yuan; Only high-end floor drains will use 304 material, but ** is relatively high, generally around 100 yuan.

It is slightly lower around the drain than in other places, so that the water does not remain on the ground during bathing, but flows quickly to the drain.

The slope should be adjusted in the direction of the flowing water to make the passage of the flowing water a little lower, so that the speed of the flowing water can be increased, so that the water flow rate in the bathroom will be very fast.

It should be tilted a little more so that the water can flow out quickly, and it will not cause blisters to damage the floor.

Look at the size of the bathroom. My bathroom was about 7 square meters, and there was only one floor drain at that time.

Regretted it. Because the bathing area is close to the innermost, the water can flow smoothly into the floor drain. But the washing area is often dirty, when I clean the bathroom, this leads to our bathroom tiles, if you just look for a slope to this one floor drain, it will lead to a large slope, paved floor tiles.

Noticeable unevenness. So I personally recommend installing another floor drain next to the toilet. In this way, if there is water on the ground in other areas, it can flow down this floor drain. It is also necessary to use a broom.

Or mop the water into it, so that the water can flow smoothly into the floor drain, otherwise the ground is full of water.

<> secondary waterproofing is: the floor layer is waterproof, and the waterproof effect is better than that of the later filling and plugging floor drain. In the later stage, the waterproofing of floor drain must be dealt with well, which is the main leakage point.

Generally, it is not recommended to increase floor drains, the drainage pipes are located under the floor slab, the construction is inconvenient, and the construction needs to be carried out in the downstairs room, and the hidden danger of water leakage is also relatively large. If it is the same floor drainage.

It can be more convenient and can be increased. At the lowest point of the same floor drain pipe, drill 4 holes in the southeast, northwest and northwest, superimpose plastic sheets, and lay cement mortar on top.

Then do waterproofing, and then paste porcelain tiles. At least one floor drain is installed in the bathroom, in fact, you don't count this, this is the developer's final say, leave a few holes and install a few.

It is more appropriate to install two floor drains in the bathroom, one is under the shower, where the floor drain needs to be slightly larger, drain a little faster, try to be close to the shower, and do not affect the position of the foot pad. The other one is made in washbasins and toilets.

between, is in the dry zone. There are toilets and washbasins outside the shower room, and there is often open water on the floor.

Therefore, it is necessary to install a floor drain, and use this floor drain as the lowest point to adjust the slope, so that there is no water accumulation and the water is fast. This floor drain should be installed in a suitable place according to local conditions, but not in the visible area of the bathroom door, try to put it on the side. If you have a washing machine, you also need to reserve a floor drain.

If you forget the slope when installing a bathroom drain, then the problem can become very tricky. Restroom floor drains require a slope that allows water to drain out of the floor drain and into the drain. If there is a lack of slope, the water will not be able to flow and may eventually cause water to build up on the bathroom floor or leak.

Here are some ways you can try to solve the problem of missing slope of the floor drain in the bathroom:

1.Reinstall the floor drain and make sure the slope: this is the best way to deal with the problem. When reinstalling the drain, make sure to use a horizontal lead ominizer to ensure that the drain slope is correct and that water can flow from there to the sewer.

2.Use additional materials that come with the floor drain: Some bathroom floor drains are designed with additional materials to help create the desired slope. Check the installation instructions to see if there is additional support material available.

3.Add another drain: If you can't reinstall the drain, you can add another drain. This will cause water to flow into both drains, and eventually cause the water to flow around the drain that has no slope.

4.Change the floor: If all else fails, only changing the floor will solve the problem. This will leave you needing to replace the entire underground drainage system, which can be very time-consuming and costly.

Before trying any of these methods, you should consider hiring a professional, such as a plumber, to fix the restroom floor drain to ensure that everything is done correctly. This bridge will avoid further damage and costs, and will ensure that the restroom drainage system is functioning properly.

Floor drain is an indispensable hardware product in the decoration process of modern bathroom space, which can make the water on the floor of the bathroom space drain out immediately and keep the entire bathroom space dry, but if the bathroom floor drain drainage is slow, it will affect the normal use of the user. What should I do if the floor drain in the bathroom is slow? Let me take a look.

In fact, whether the floor drain drainage is smooth or not is mainly determined by the slope of the bathroom floor and the installation effect of the floor drain itself. To solve this problem, you can focus on the following 3 points:

1. The greater the slope of the bathroom floor towards the floor drain, the smoother the drainage. Generally, the slope of the lower drainage pipe should be more than 1%, that is, the slope of the 1-meter water pipe should be more than 1 cm, and the slope of the 3-meter water pipe should be more than 3 cm. Because the bathroom drainage pipe is relatively concentrated, and the drainage during the shower is a large area, the water can flow around, if the slope is not enough, it is easy to store water or slow drainage in some places with a relatively small slope.

Therefore, the slope of the bathroom floor must be appropriate, not too big or too small, if the slope is too large, people will feel uncomfortable standing on it. 2. There is another way to solve the slope of the ground, which can be done in the place of the bathroom cabinet or toilet, which is in case of water accumulation in the bathroom, so that the water can be drained through the floor drain in these two places. The slope of these two places can be slightly gentler, close to level, and the water can flow through it with just a little slope.

But in the shower, the slope should be moderately increased. 3. There is an effective way to solve the drainage slope, which is to increase the slope around the floor drain, install the bricks of the floor drain diagonally, and put the floor drain in the middle of the brick, so that the slope of the floor drain is very obvious. However, before installation, the owner should dock with the master and tell the master the size and specifications of the bathroom floor tiles, so that the master can install the floor drain.

Summary: The relevant information about the slow drain of the bathroom or what to do with the socks is introduced here, I hope this article will be helpful to you. If you still don't understand something, you can leave me a message below, and we will answer it for you as soon as possible.

Usually the slope of the floor tiles, that is, the vertical height of the subsidence, should be between 1% and 2% of the length and width of the floor tiles, which is generally understood to be 1 cm to 2 cm, so as to ensure the smooth flow of water to the floor drain.

The bathroom floor should be inclined to the direction of the floor drain, the slope is too small, if there is too much water, it will flow to the outside, and the slow drainage makes the sewage often precipitate in the drainage process, resulting in a smell of stinky water in the bathroom.

If the slope is too large, although the stagnant water can be discharged quickly, the uneven ground will cause various furniture in the bathroom to tilt, and there will be a feeling of going up and down the slope when entering and exiting the bathroom, and the elderly are easy to slip.

The overall slope is 1-2%, and the floor drain is the lowest point, which is 1-2mm lower than the tile.

The slope of the ground with drainage requirements during paving should meet the drainage requirements, and the visual inspection of water splashing does not accumulate water to meet the requirements. The 2% water slope is quite exaggerated, which means that the 2-meter-long bathroom can reach a horizontal drop of 4cm from the high point to the low point, so it is impossible to have stagnant water. The slope of the water is based on the principle of not accumulating water or as the standard.

The slope of this floor drain needs to be carefully considered, and any leakage will cause water seepage in the bathroom.

The specific inclination of the ground is not explained, the main thing is that the water can not flow too fast, nor too slow, you can use a ping pong ball to put on the ground, see the speed of its rolling, and feel that the moderate is the appropriate slope of the ground. Personally, I think it's still up to feeling.

Make sure that there is no water accumulation in the bathroom;

Hello, glad to answer for you. For you to find out that the best way to paste the bathroom floor tiles and let them go into the water is to take the floor drain as the lowest point, and then put the slope well, and install the brick in the floor drain as a funnel. Bridge trap 1, pull a few lines to find the slope, but try to have a large slope.

2. Use a level and a large slope. Generally, the workers themselves will make a slope of the ground level, and continue to lower it from the position of the surrounding drain, and then the water can naturally flow down the slope to the drain of the floor. As for the material of the tile, it is now more commonly used to use the tile Li Xiao glue to compaction, not only the construction is simpler, but also the bonding force is also 3 times that of the previous cement river sand, so it is more and more popular with the owners.

I hope I'm stupid enough to help you, and I wish you a happy life, thank you.

In home decoration, almost everyone knows that the bathroom floor should have some slope, perhaps because the slope is larger will affect the beauty of the ground and require the construction personnel to slow down the slope of the bathroom floor, the result is likely to lead to the water after the shower can not be drained in time, and it is difficult to drain the water when washing clothes. However, the slow drainage of mountain cherry blossoms makes the sewage often precipitate during the drainage process, resulting in a smell of smelly water in the bathroom. Today, let's talk about the toilet drainage method of toilet drainage slope remedy.

According to the principle of pragmatism, in home decoration, aesthetics is only a superficial phenomenon, and when it is critical, it can be ignored. In this regard, combined with the experience of their own bathroom decoration, netizens "because" according to their own actual combat situation, according to their own actual situation, without affecting the placement of toilets and bathtubs, the slope of the bathroom should be appropriately enlarged to avoid indoor water accumulation after laundry and bathing. If the ground work has been done, then when buying bathroom products, you should choose products with deep inner walls, which will also avoid water splashing.

If you don't make a shower room slag bush, it is best to hang a shower curtain outside the shower or bathtub, which also has the effect of "making up for the work".