Insulating glass fogging repair or replacement? How to deal with the fogging of insulating glass

1.Nowadays, many families will choose insulating glass.

To install, the most important thing is to be able to achieve the effect of sound insulation. In addition to insulating glass, there is also vacuum glass in addition to insulating glass, and there is a difference between the two, that is, the insulating glass uses a desiccant.

It can drain all the moisture inside. However, if the seal is not tight, there will be fogging problems in the later stage.

If this happens to the windows of your home, you can seal the insulating glass again and seal the perimeter to prevent air or moisture from entering. Wait until the inside is dry, and then put another layer of glass glue in the window glass frame.

It can solve the phenomenon of poor sealing, and the problem of fogging will not occur again in the later stage.

There is also a solution to the problem, which can be added to the glass gasket in the insulating glass window.

Remove all the isolation strips and reinstall them. The pasted position is kept at a certain distance from the edge of the window, generally speaking, up to 2 mm, and then do not get wet, and wait until it is completely solidified, and it can be used normally.

If there is fogging in the middle, it means that the sealing of the glass has failed, which has reduced the performance of the insulating glass.

Maintenance is not as reliable as replacing a new one on Zhilian, and the cost of maintenance is equivalent to having to completely dismantle, then clean, repackage, and the cost of maintenance is more expensive than that of a new one.

If you are a commercial house, contact the property directly to ask the aluminum window team to replace it. This is a glass manufacturer's own process is not done well, and it is an unqualified product.

The fogging of insulating glass can be repaired, mostly because the laminate is not tightly sealed.

1. If there is fogging, it means that the insulating glass is not sealed around it. The air is humid, or when water or air enters, fogging may occur in the middle.

2. After the inside is dried, it is necessary to re-seal it, and then squeeze the glass infiltration with glass glue on the outside of the glass frame spacer, pay attention to the sealing effect, and the cluster finger can solve the problem of glass fogging and moisture.

3. In addition, we can also increase the gasket, because if the glass window is not completely closed, the isolation strip needs to be installed properly, and at the same time, the gasket can be added to the window, the original sealing strip can be removed, pay attention to the position of the paste and the edge of the glass window to keep a certain distance, generally speaking, up to about two millimeters, and at the same time pay attention to avoid water stains during operation.

4. There is also a good way to solve the problem, which can open a balance hole at the insulating glass, which can effectively drain water and avoid the problem of fogging.

Precautions for insulating glass

1. Detect the indoor temperature: If the temperature difference between the inside and outside is relatively large, it is likely that the warm air in the house will liquefy to the glass. Or the humidity of the air in the room can also cause fogging on the glass.

At this time, it should be checked whether the molecular sieve amount of the septum is insufficient, and if it is not enough, it needs to be added.

2. Reinstall the sink position: If the position of the sink of the double-glazed window is not installed, the double-glazed window needs to be removed and reinstalled, which is also to ask a professional master to carry out the construction.

As a result, the seal between the two pieces of glass has failed, causing moisture to enter. If the spacer between the two pieces of glass that makes up the insulating glass contains a desiccant, it can cope with the small amount of water vapor entering the compartment during manufacturing or use, and you should have a large amount of water vapor entering the compartment during manufacturing or use. You can ask the master to disassemble the insulating glass and replace it with a new spacer.

This can't be dealt with by yourself, at most use heating equipment to bake the water vapor inside the window, but not too hot too close, otherwise the glass will burst, but it can only be disposed of for a while, and there will be two days later.

<> I noticed that there is often moisture in the double glazed windows of my house in the morning and evening, and as soon as the sun comes out, it is gone, and the fog is very ugly. After my careful observation, I found that there is this phenomenon in my house, and the windows of my neighbor's house are fine, what is going on? How do I remove glass from a window?

The glass of plastic steel windows is the best to take, unlike aluminum alloy, both sides are sealed, and plastic steel windows are not glued, with a slotter from the middle of the longest strip, the upper strip finally down, so that the glass can be removed.

Drill two holes in the bottom and upper part of the glass, so that the air is convective up and down, and it will dry out in a few days, and there will be no moisture in the middle of the insulating glass. After a long time, you have to find a professional to scrape the hollow rubber elephant with a knife, wipe it clean and fix the new rubber strip on the mother's glass, but this costs money.

This phenomenon occurs when the adhesive of the insulating glass cracks, causing gas to enter, and water vapor occurs when hot and cold meet. The solution is to remove the glass, re-evacuate, and then seal it with a special structural adhesive. In addition, the original middle spacer can also be removed, and when reinstalling the spacer, it should be noted that the pasting position of the spacer should maintain a certain distance from the edge of the glass window, generally 2mm is the most appropriate.

And when installing glass windows, be careful not to get water on the partition, so as not to affect the installation quality.

Personally, I think that at this time, it must be to blow a cold wind for him, and then slowly reduce his fog, which is relatively easy.

There is no good way, unless you change it again, the insulating glass is vacuum, if once opened, the glass will lose its effect.

The light inside should be adjusted well, because only then can you see what is outside better.

Hello, for the case of insulating glass fogging, I know that repair is OK, if the insulating glass is only slightly foggy, you can consider repairing. The method of repair is usually to solve the fogging problem by removing the moisture inside the glass by special injection substances or special treatments. The restoration process generally does not require the replacement of the whole piece of glass, and the cost is relatively low.

However, if the fogging inside the insulating glass is severe, causing problems such as blurred vision or affecting aesthetics, it is recommended to replace the whole piece of glass. This is because severe fogging can mean that the inner seal of the insulating glass has been broken and cannot be repaired effectively. In this case, replacing the entire piece of glass is the best solution.

In short, for the fogging of insulating glass, it is recommended to ask a professional to test and judge the limb burial, and then choose to repair or replace it according to the specific situation. At the same time, it is necessary to pay attention to maintenance to avoid the insulating glass from moisture or external impact, which can prolong the service life of the insulating glass.

Vacuum glass fogging repair method: seal again, add gasket, test the indoor temperature, open an air pressure balance hole, and reinstall the sink position.

1. Seal again

If the perimeter of the insulating glass is not sealed, then it is easy to cause air or rain to enter, so it is necessary to wait until the inside is dry and put a layer of glass glue on the outside of the glass frame spacer, which can effectively alleviate the phenomenon of non-sealing and reduce the fogging and moisture of the glass.

2. Add a gasket

If the glass window is well sealed and the septum is properly installed, then the glass gasket can be added to the insulating glass window, and the original septum is removed and then reinstalled.

3. Detect the indoor temperature

If the temperature difference between the inside and outside is relatively large, it is likely that the warm air in the house liquefies to the glass, or the indoor air humidity will also cause fogging on the glass.

4. Set up an air pressure balance hole

If the glass fogging is caused by air pressure, it is necessary to open a certain air pressure balance hole to drain the water, which needs to be operated by a professional master to solve it. Envy Rock.

5. Reinstall the sink position

If the sink of the double-glazed window is not properly placed, the double-glazed window needs to be removed and reinstalled, which is also to ask a professional master to carry out the construction.

1. Remove the sealing strip and use sunlight to evaporate the water vapor; If it's too slow, you might as well use a hair dryer to blow it, which can also remove the problem of water vapor.

2. It is also possible to strengthen the sealing, but the premise is that the water vapor on the inside of the glass has been removed. For example, add moisture-proof strips to the inside of the window frame.

3. If it is caused by the aging of the sealing strip, it is recommended to replace the sealing strip; If the desiccant fails, then the desiccant has to be replaced, because the function of the desiccant is to adsorb the moisture in the middle of the double-layer glass, and there will naturally be water vapor when it fails.

Insulating glass fogging is often caused by poor sealing performance, which can affect the transparency and aesthetics of the window. For the problem of fogging up insulating glass, you can try the following two methods to fix it:

1.Insulating glass defroster: There are some defrosters on the market that are specially used to remove water vapor inside insulating glass, which can be stuffed between the double layers of glass by spraying or dripping to achieve the purpose of defrosting.

Before use, you need to carefully understand the usage methods and safety precautions in the instructions to avoid unnecessary damage or other risks.

2.Glass replacement: If insulating glass defroster does not solve the problem, you need to consider replacing the glass with a new insulating glass.

At this time, you need to find a professional glass repair company or window manufacturer to consult, and get their ** and advice. If you need to replace a large area of insulating glass, it may be higher, but the effect will be more desirable and long-lasting.

It should be noted that the above methods are for reference only, and the specific repair plan needs to be determined according to the specific situation. If you do not have the relevant experience or skills, it is advisable to seek the help of a professional technician to ensure safe and reliable operation.