The hollow glass is fogged in the middle, how to deal with it to see clearly?

As a result, the seal between the two pieces of glass has failed, causing moisture to enter. If the spacer between the two pieces of glass that makes up the insulating glass contains a desiccant, it can cope with the small amount of water vapor entering the compartment during manufacturing or use, and you should have a large amount of water vapor entering the compartment during manufacturing or use. You can ask the master to disassemble the insulating glass and replace it with a new spacer.

This can't be dealt with by yourself, at most use heating equipment to bake the water vapor inside the window, but not too hot too close, otherwise the glass will burst, but it can only be disposed of for a while, and there will be two days later.

<> I noticed that there is often moisture in the double glazed windows of my house in the morning and evening, and as soon as the sun comes out, it is gone, and the fog is very ugly. After my careful observation, I found that there is this phenomenon in my house, and the windows of my neighbor's house are fine, what is going on? How do I remove glass from a window?

The glass of plastic steel windows is the best to take, unlike aluminum alloy, both sides are sealed, and plastic steel windows are not glued, with a slotter from the middle of the longest strip, the upper strip finally down, so that the glass can be removed.

Drill two holes in the bottom and upper part of the glass, so that the air is convective up and down, and it will dry out in a few days, and there will be no moisture in the middle of the insulating glass. After a long time, you have to find a professional to scrape the hollow rubber elephant with a knife, wipe it clean and fix the new rubber strip on the mother's glass, but this costs money.

This phenomenon occurs when the adhesive of the insulating glass cracks, causing gas to enter, and water vapor occurs when hot and cold meet. The solution is to remove the glass, re-evacuate, and then seal it with a special structural adhesive. In addition, the original middle spacer can also be removed, and when reinstalling the spacer, it should be noted that the pasting position of the spacer should maintain a certain distance from the edge of the glass window, generally 2mm is the most appropriate.

And when installing glass windows, be careful not to get water on the partition, so as not to affect the installation quality.

Personally, I think that at this time, it must be to blow a cold wind for him, and then slowly reduce his fog, which is relatively easy.

There is no good way, unless you change it again, the insulating glass is vacuum, if once opened, the glass will lose its effect.

The light inside should be adjusted well, because only then can you see what is outside better.

1. Seal againIf insulating glass.

If the surrounding area is not sealed, it is easy to cause air or rain to enter, so wait until the inside is dry and put a layer of glass glue on the outside of the glass frame spacer.

It can effectively alleviate the phenomenon of non-sealing and reduce the fogging and moisture of the glass.

2. Add a gasketIf the glass window is well sealed and the spacer is properly installed, then the glass gasket can be added to the insulating glass window, and the original spacer is removed and then reinstalled, and the position of the spacer paste is kept at a certain distance from the edge of the glass window, generally 2mm is more appropriate, and do not get water on the spacer when installing the glass window, so as not to affect the use.

The fog in the glass will disappear on its own.

The fog in the glass will disappear on its own, so as long as it does not affect your life, you don't need to deal with the fog in the insulating glass, which is the water vapor in the air.

It is liquefied after being cold, and as long as it encounters warm weather, the fog will disperse by itself.

A common cause of insulating glass fogging.

Poor installation process of insulating glass: due to poor construction technology during the installation of insulating glass, the sealant will crack over time, and then water vapor will enter the middle layer of insulating glass from the position of the crack, and with the increase of the temperature of doors and windows, water vapor will naturally appear in the middle layer, which is one of the reasons for fogging of insulating glass.

The insulating glass sink is not installed: when the insulating glass is installed, the sink inside is not installed due to the sloppiness of the construction workers, resulting in the water surface being higher than the profile, which is easy to flow water into the middle layer of the insulating glass, and the profile water vapor or water droplets will naturally occur under the irradiation of the sun.

When the insulating glass is installed, the sealing spacer is not done: the middle layer of the insulating glass is blocked by a spacer, if the spacer is not done well, then when it rains, the doors and windows are in contact with the rainwater, and the natural rainwater will be adsorbed on the insulating glass, which will lead to the occurrence of fogging. On the contrary, the main cause of fogging of most insulating glass is due to poor installation.

A solution to the fogging of insulating glass.

1. If the insulating glass is fogged because the sealant is not tightly winded, the sealant of the insulating glass can generally be removed first, and the glass sealant can be re-painted after the middle layer is dry, so the problem of fogging can be solved.

2. If the sink of the insulating glass is not installed, it is recommended to find a construction worker to remove the insulating glass window, and reinstall it after the middle layer is dry.

3. If the double-glazed insulating glass spacer has been installed, a glass gasket can be added to the double-glazed window. In addition, the original partition strip can also be removed, and when reinstalling the partition, it should be noted that the pasting position of the partition should maintain a certain distance from the edge of the glass window, generally 2mm is the most appropriate, and this process must be kept dry throughout the process.

If the sealant is not tightly sealed, the sealant can be removed, and the glass window can be cleaned again, and after it is dry, the glass sealant can be painted.

If the sink location is not properly installed, remove the window and reinstall it.

Dear, I am glad to answer for you: the fog inside the insulating glass is like this: 1. What should I do if the insulating glass is fogged in the middle, and this situation shows that the sealing effect around the insulating glass is not good, and the air is humid or affected by water and air.

After the inside is dry, it is necessary to carry out sealing construction again, and squeeze glass glue on the outside of the glass frame spacer again, and pay attention to the good sealing effect of Hongwei, so that the problem can be solved. In addition, gaskets can also be added, if the glass window is not completely closed, then the isolation strip must be installed properly, you can also add a gasket to the window, remove the original sealing strip, carefully paste the place to maintain the corresponding distance from the edge of the glass window, the normal is about two millimeters, and the implementation should avoid water stains. You can also drill a balance hole on the side of the insulating glass, so that the water can be drained and the fog will not appear again.

2. What is insulating glass 1, it is a kind of glass made by the Americans in the 19th century, with the effect of heat insulation and sound insulation, and is an important building material, mainly made of two or more pieces of glass, and the paste is also used in the production, so as to ensure that the glass sheet and the dry frame can be firmly connected. 2. The middle part is hollow, which can ensure the sound insulation effect, and it has better performance than Puzhen Rangtong and double-layer glass, so the range of use is broader, and the main materials are glass, desiccant, sealing strips, etc. 3. High-quality insulating glass also has the ability to save energy, it can reduce heat transfer, and the sound insulation effect is excellent, if the air conditioning and heating inside the window are running, this can ensure the indoor temperature balance.

Summary: The above is the solution to the insulating glass in the middle, from the above article we can see that there are many practical solutions, we must refer to the specific situation of our own family when choosing, so as to ensure that the problem is solved, and will not damage the doors and windows.

1. Nowadays, many families will choose insulating glass to install, and the most important thing is to achieve the effect of sound insulation. In addition to the insulating glass, there is also vacuum glass, and there is a difference between the two, that is, the insulating glass uses a desiccant, which can pump out all the moisture inside. However, if the seal is not tight, there will be fogging problems in the later stage.

2. If there is such a situation in the windows of the home, the insulating glass can be sealed again, and the surrounding area can be sealed to avoid the entry of air or water vapor. After the inside is dry, then put another layer of glass glue in the window glass frame, which can solve the phenomenon of poor sealing, and there will be no fogging problem again in the later stage.

3. There is also a solution, you can add a gasket to the glass in the insulating glass window, remove all the isolation strips, and reinstall them. The pasted position is kept at a certain distance from the edge of the window, generally up to 2 mm in the noise, and then do not get wet, and wait until it is completely solidified, and it can be used normally.

Hello, I am happy to serve you: fogging on the surface of insulating glass is operated as follows: 1. We can use a towel to wipe off the fog, and then open a small slit in the glass to let the outside air flow into the room, which can effectively help us solve the problem of fogging on the glass.

2. You can also buy some anti-fogging agent to apply on the glass, if the glass is fogged, we can use a dry towel to wipe all the fog on the glass, and then apply the anti-fogging agent to the glass window, which can maintain the glass fogging problem for a long time. 3. Put dish soap and soap in water, wait for the two to melt, soak them with a rag, and wipe the fogged glass, which can prevent fogging from happening again, because soap and dish soap will generate a film on the glass, which can be used instead of anti-fog film, and this method is also very easy to use. 4. If you find that the indoor window is fogged, we can also use the on-board anti-fog spray to spray it.

This will also have a certain effect on the windows of the room to remove fog. 5. If you want to effectively prevent the indoor windows from fogging, you should usually ventilate and open the windows more, don't let the indoor temperature be too high, and try to open a small layer of tassels in the windows when cooking rice or soup to prevent fogging and even dripping water on the glass. Thank you for your trust, the above is my reply, I hope that Zen can help you, guess the staring thank you!

Have a great day.