How big can a fish tank bear in a building?

There is still a possibility of a burst:

1. The stone is supported by buoyancy underwater: the gravity of 40 catties of stone will be reduced when placed underwater: if you cut off 20 catties of buoyancy, there will only be 20 catties of weight left (the size of the stone is unknown, so it can only be estimated).

2. The main concern is whether the bottom of the stone is flat: if you want to find a way to make the bottom of the stone flat, you don't have to worry about the force relationship with the bottom of the fish tank. It must be ensured that the flatter the bottom of the stone and the larger the area, the greater the possibility of fracturing the glass at the bottom of the cylinder.

3. The most important thing depends on: the thickness and strength of the glass at the bottom of the cylinder. In addition, whether the table under the cylinder is flat and evenly matched will have a lot to do with it.

It should be considered: the table under the cylinder should be covered with a layer of 3cm thick rubber skin or hard foam board to ensure the gravity cushioning inside and outside the cylinder. The main thing is to avoid bursting due to uneven force on the bottom glass.

Therefore, thinking carefully and being ready to act is the best way to reduce trouble. (It's the same in every home: having a safe fish tank is a fish tank; Conversely, an unsafe fish tank is a mine!

Safety always comes first, and there is no such thing as a fluke.

Look at the thickness of your glass, if the glass is more than eight no problem, if five millimeters then slowly add water, first add to two-thirds of the problem, if your fish tank is a finished tank can accommodate nearly three hundred pounds of water, the base glass must be thickened, that is to say, it should be more than ten, if you add water for a day, then you can be full of water, eight glass, the base is thickened no problem.

It depends on the thickness of the glass and the condition of the bonding.

There is also a shelf that is placed.

Generally speaking, if the shelf is stable and the support below is sufficient, it should be fine.

The main thing is to see how thick the bottom glass is.

When placing a fish tank in a building, be sure to choose a wall.

2*1*tons of water, if full, tons.

It is not possible to design according to the normal design, because the variable load of the normal design such as residences, dormitories, office buildings, classrooms, rooms, etc. is more than two tons, which is more difficult to say. The load range requires that the live load of the floor slab of civil buildings cannot be less than per square meter, that is, not less than 250 kg per square meter. There shouldn't be a big problem, and the general furnishings can't reach 250 kilograms per square meter.

I want to get off the piano and ...... on all four feet

The weight, compared to a fish tank, and the bathtub, filled with water ......

The weight bearing of the 1 meter 50 wide and 50 high fish tank is as follows:Calculated volume: 1 cubic meter = 250 cubic decimeters.

So it can hold 250L of water

Fish tank, a kind of water tank for live fish, the tank body is transparent, mostly glass, and can also be used to raise tropical fish or goldfish for ornamental purposes.

The fish tank is not only a home for the fish, but also a common life for the family. The flawless double-layer floating glass not only creates a warm home for the fish, but also ensures the safety of the overall living environment. The fish tank is an indispensable ornament in home feng shui, a perfect combination with space, and a soul Zen master of home, office and commercial space.

Summary. Hello dear, the information I found for you shows that the load-bearing problem of the fish tank in the building should be backed by the load-bearing wall as much as possible. When placing a larger fish tank, the back of the fish tank is best attached to the load-bearing wall, which is really not good, at least one side of the fish tank should be next to the load-bearing wall.

Hello dear, the information I found for you shows that the load-bearing problem of the fish tank in the building should be backed by the load-bearing wall as much as possible. When placing a larger fish tank, the back of the fish tank is best attached to the load-bearing wall, which is really not good, at least one side of the fish tank should be next to the load-bearing wall. The land sparrow calls.

I'm going to buy a goldfish bowl, meter long, 70 wide, 50 high.

I calculated the weight, probably around 1 ton.

Put against the wall. I'm just afraid that the fish tank will be too heavy and collapse the building or break the structure.

Yes. A rough calculation is 1880 pounds.

It's a bit heavy. How many catties is the force area per square meter of the building?

The standard deviation of the load-bearing capacity of the building is a square meter of slag per square meter. 1. The residential building is not less than 200 kilograms per square meter, the floor is load-bearing per square meter, the general live load value, the living room and living room are 2000kn, close to 200 kilograms, and the square meter is less than 200 kilograms.

<> load-bearing capacity of the fish tank is related to many factors, such as whether there are tension ribs, the thickness of the glass, the size of the fish tank, and so on. Usually there is nothing wrong with putting 10 kilograms of something, but it is difficult to say if it is larger. If you are worried that the upper filter will crush the fish tank, you can change to other filtration equipment, such as bottom filter, filter cartridge, etc., different filtration equipment has its own advantages and disadvantages, some have good effects, and some are easy to clean, which mainly depends on personal choice.