What is the reason why the Mido M7600 3 26 8 watch is not gone

Underpowered, the movement of this watch has a maximum power reserve of 38 hours, which means that if it is not moved for a maximum of 38 hours, it will stop running.

If it has been worn continuously for more than 5 years, it is likely that there is severe friction inside the movement or other conditions that need to be cleaned and maintained.

Movement failure, fall, violent**, may also be an assembly problem, which needs to be taken to after-sales repair.

Fake watch, the movement inside the fake watch is very waste, and it is normal not to go, just throw it away.

You can go to the after-sales service to see, Wanling Hui has an after-sales service, don't go to those small repair shops for maintenance. After-sales service not only has professional technology and precision instruments, but also has more high-quality service and first-class system. It will not be messed up with other repair shops at all, and you don't have to worry about the quality of watch repair - 1 year extended warranty.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

There will be after-sales ** on your warranty link, call after-sales ** to inquire about the after-sales address.

MIDO (MIDO) Belen Cyli series mechanical men's watch (see picture below) uses ETA2824-2 automatic movement, and the unified sales price of domestic officially authorized stores (cabinets) is 6,000 yuan, which can generally be sold at a 10% discount.

On the one hand, it may be a lack of power and a few minutes of stealing; On the other hand, it is possible that there is something wrong with the hairspring; If you stop while skipping the calendar, it may be that the skipping part is damaged or stuck. If the mechanical watch is not powered enough, as long as it is fully wound in time. If there is a problem with the internal parts of the movement, it must be sent to a professional repair center for repair.

Hello, glad to answer for you!

The main reasons why the watch does not go are the misalignment of the core gear, the magnetism of the watch, bumps, and the long shelving time, and the oil sludge is dry. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch suddenly stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours.

If the watch is used for a long time, then its wear and tear will be more serious, and the external maintenance of the watch will be easily damaged. It is necessary to regularly replace the watch you are wearing, and it is necessary to maintain the watch regularly, for the service life of your watch, it is better to maintain it regularly.

The reason why the mechanical watch stops is that if it stops under the premise that it has not been bumped, it is usually due to a lack of power, you can fill the mainspring every morning to see if there is still such a stoppage. If this is still the case, it is recommended that you go to a professional repair shop and let the master check it. In addition, the mechanical watch should be fully maintained in 3-5 years, and the oil should be washed and lubricated to ensure that the internal parts of the movement can operate normally.

In fact, there are many reasons why mechanical watches do not go, such as: bumps, movement gear misalignment, magnetization of the watch, shelving for a long time, sludge drying, etc., generally divided into two kinds, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch.

Therefore, don't panic too much when you find that the mechanical watch is not leaving, and first distinguish which kind of big one it belongs to.

1. Insufficient power reserve. You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of speed and slowness, if it is still recommended to go to the store for testing.

2. The power is insufficient. If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy.

3. Having been beaten or impacted. The watch is very tight, if it is hit or dropped, it may cause loose damage to the internal parts, and it may also cause time problems, so it is recommended to go to the store for testing.

4. Maintenance is required. A lack of oil or wear and tear of the internal parts of the movement can cause time-keeping problems and require maintenance.

5. Under the influence of ambient temperature, the watch is magnetized: if the hairspring of the watch is magnetized, the watch will not be accurate. The influence of the wearer's usage habits may cause an increase in the error of the time, which will be sent to the store.

Note: 1. Mechanical watches vary according to the model and manufacturing quality of the movement, and the error of the general watch within 30 seconds per day is within the normal range. Some of the higher precision movements can reach around 10 seconds.

Stop, there may be the following reasons:

1. See if the crown is pulled out, the crown is pulled out, and the watch stops.

2. Whether the second hand touches the glass, there will be a circle mark on the glass.

3. Whether the three watch hands are not well balanced, causing contact and causing stopping.

4. Whether the battery is exhausted or not, it generally needs to be replaced in 1-2 years.

Your watch model is given the wrong one.

The right thing to be: the Mido Men's Collection.

Ref: Brand: Mido.

Series: Belen Seri.

Movement Type: Automatic.

Gender: Men.

**：¥ 6,000 2012-06

EUR: Not included.

HKD: HK$ 6,300 2014-10

Caliber number: ETA 2824-2

Out of the loss of a smile manufacturer: ETA

Caliber diameter: mm.

Movement thickness: mm.

Frequency: 28800 oscillations per hour.

Number of jewels: 25.

Power reserve: 38 hours.

Case diameter: 38 mm.

Case material: Stainless steel.

Dial color: White.

Dial shape: round.

Glass material: anti-reflective sapphire crystal.

Strap color: Silver.

Bracelet material: stainless steel.

Clasp Type: Folding Clasp.

Clasp material: stainless steel.

Back penetration: Back penetration.

Water resistance: 50 meters.

Date display.

The model number of the white disk is: The official price of this watch is 10,000, and of course 3,000 cannot be true.