What should I do if the hands of my Roger Dubuis watch fall off?

When the watch is subjected to severe vibrations, the hands may fall off, especially the second hand. If the second hand (including the small seconds or other hands) has fallen off and may get stuck between the hours, minutes and the dial, the second hand will be plucked and scratched against the dial if the watch continues to move, causing scratches to the dial. If you find that the watch hands are displaced or fall off, you must stop the watch immediately, and if there is no stop second device, you must also pull out the watch handle to let the watch gradually stop.

Hello, glad to answer for you!

When the watch is worn and used daily, it is easy for the watch hands to fall off when it is impacted. Since the hands are installed in layers, and the top tube is connected to the second hand, the second hand is usually lost.

Watch hands fall off need attention:

1. Avoid moving the watch, so that the hands scratch the dial or the hands are damaged.

2. For some hollow watches, try to avoid the small needle falling behind the dial.

3. After the crown of the watch is pulled out, it should be repaired in time to prevent the watch from entering the dust and damaging the movement.

It is recommended that you can open the warranty coupon attached to the purchase of the watch, under normal circumstances, there will be a service address on the warranty copy, or find a regular watch service center for testing and maintenance of the address of the store, etc., if there is a professional after-sales maintenance center nearby.

If there is a problem with the watch, it is recommended to go to the regular after-sales service for maintenance, not only the technician is more professional, the instrument is also more precise, and the **transparent is not messy**. There is a very good after-sales service near Wanling Hui in Tianhe District, so I will go to see it when I have time. My personal advice is to pass as soon as possible, otherwise the longer the time, the greater the problem with the watch, and the greater the economic loss.

The main thing is that it is still more troublesome, and the repair time will become longer.

If there are rust stains on the dial of the watch, the watch has been flooded. Rust on the dial will not only affect the normal use of the watch, but also may reduce the service life of the watch, it is recommended to send it to a professional after-sales maintenance center for repair immediately.

If the watch is not treated in time after water ingress, it is easy to cause the movement, dial, hands and other internal parts of the watch to rust, which may reduce the service life of the watch.

For some expensive watches, you need to pay more attention to maintenance in use, regularly clean the stains on the watch case, and maintain the watch every 2-3 years or so.

1. If your watch is getting slower and slower within a year of buying it, it may be that the watch has been in contact with magnetic items, and you can bury it in the repair center to demagnetize, and then please avoid the contact between the watch and magnetic items. It could also be that the oil has not been washed for a long time, or the gears may be misaligned due to vibration.

2. Lack of maintenance: mechanical watches are maintained every 2-3 years, and quartz watches are maintained every 4-5 years. The watch maintenance should completely disassemble, clean, oil, reassemble, adjust, and check the function of the movement; Repair or replace any worn or malfunctioning movement components.

If the watch lacks maintenance, it will lead to the wear and tear of the parts, the sludge will dry up, affect the normal running time of the watch, and make the watch appear fast and slow. Regular maintenance of the whole machine can effectively prevent the occurrence of various failures of the watch.

3. Mechanical failure: Mechanical failures such as watch hairspring failures, escapement system failures, and parts and components may cause the watch to appear fast and slow, so when the watch is abnormal, you can first pull out the crown and take it to a professional maintenance organization for the maintenance technician to check the reason.

4. The mechanical watch may be fast and slow, which may be caused by severe impact, water ingress and other reasons.

First of all, this lifting out of the 100 watch burning high crown should be pulled in time to stop the movement, to prevent the hands from scratching the watch, dial or damaging the dial.

Secondly, after pulling out the crown, please repair it in time to avoid the dust of the watch from entering.

Third, if the degree is a hollow watch, try to avoid the small hands falling into the back of the dial.

Fourth, when installing both hands, pay attention to choosing a formal mechanism to prevent scratching the improper operation of the dial plate, resulting in a decrease in the waterproof performance of the watch.

In general, maintenance is relatively easy if there is no damage to the inside of the watch. If the wheel tube is deformed, broken, or the parts are worn, the repair will be slightly more difficult. Please note that watches with hands need to be fully tested for water resistance, and the waterproof ring will need to be replaced when the old forest section is aged.

1.The power of the table is insufficient.

An automatic watch only needs to be wound by moving your arm, but if you don't exercise much, or if you don't wear your watch for too long, the watch may not be able to run out of time or stop due to lack of power. Of course, you don't have to throw your arms as a hula hoop in order to wind your watch, just move normally.

2.Wearing time is too short.

If it's really caused by too little exercise, don't worry, just take off your watch and shake it horizontally for about 2 minutes before going to bed, and of course you can also shake it for 4 minutes, because then it can walk longer. If your watch can be wound, you can also wind it clockwise. In order for your watch to last longer, it is recommended to have him wear it on your wrist for at least 6 to 8 hours a day.

3.Hairspring failure.

If neither of the above two reasons is the case, it may be the cause of the hairspring. If you exercise too much, the clockwork will be tighter. If it is really a lack of power caused by the winding, usually between 9 and 12 o'clock in the evening, the "calendar function table" at this time his needle wheel began to drive the calendar wheel, the load is large, the watch is tired, at this time if the power is insufficient and no one pushes it, it is easy to stop.

During this time, don't reverse the dial, many mechanical watches have a plastic calendar wheel, and if you are not careful, you will break the gear, if you break the tooth, it will be stuck at this time every day, or it will no longer jump until a fixed date. That's why the mechanical watch stopped.

4.Bump failure.

The parts of the watch are very delicate and small, if you are careless and accidentally bump into it, or if you are healthy and bump into it. This can easily cause the movement parts to fall off or break directly.

All automatic watches must be worn or wound regularly in order to function properly. If the mechanism stops working for a long time, it will cause the watch to deteriorate for a long time. Generally speaking, the power reserve of a large three-hand watch is probably no more than 38 hours, which means that if you do not wear the watch for more than 41 hours, the watch will eventually stop due to the exhaustion of the mainspring.

If you only have one or two automatic watches in your collection, you won't have to worry about wearing them often or stopping them to wind them in order to wind them. But if you have a large collection of mechanical watches, you have to make sure that all the watches don't stop, and everyone will feel a headache and trouble.

The main reasons why the watch does not go are: the movement gear is misaligned, the watch is magnetized, bumps, and the oil sludge is dried for a long time when it is left on hold. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours. Quartz watches, on the other hand, can be actively wound and should be worn on the hand for more than 8 hours a day to replenish the mainspring.

Lack of exercise after wearing it will also show that the watch does not move or stop.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

If the watch needs to be repaired or maintained, or other needs, it is best to go to after-sales, which not only has a more professional technician and better service, but also its instruments will be more precise. ** It will not be reported like other places, there are standards. The after-sales service is on the seventh floor of Tower A on the side of Wanling Hui.

If the back cover is opened in a non-designated place, it will not be eligible for the warranty.

The reason why the watch stopped:

1. Mechanical watches, usually caused by the lack of power of the watch, you can fill the clockwork every morning, if you still keep stopping, it is recommended that you go to a professional maintenance point to let the master do a professional inspection.

2. Quartz watches are usually because the battery is about to run out, and it can be solved by replacing the battery.

1.Insufficient power reserve: You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch may also cause insufficient power reserve, you can replenish the power by manual winding, and then observe whether it continues to be fast or slow.

2.Having been hit or impacted: The watch is very tight, and if it is hit or hit, it may cause loose damage to the internal parts, or it may cause time problems. This is to be dealt with in a timely manner.

3.Need for maintenance: The lack of oil or the wear and aging of the internal parts of the movement may cause time problems, which need to be serviced and sent to a designated repair point for maintenance services.

4.In addition to the above common situations, the watch is affected by some ambient temperatures: if the balance spring of the watch is magnetized, the watch will not be accurate.

Roger Dubuis Watches After-Sales Center is located at: Room 808, Block E1, Oriental Plaza, No. 1 East Chang'an Street, Dongcheng District, Beijing.

In fact, there are many reasons why mechanical watches do not go, such as: bumps, movement gear misalignment, magnetization of the watch, shelving for a long time, sludge drying, etc., generally divided into two kinds, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch.

Therefore, don't panic too much when you find that the mechanical watch is not leaving, and first distinguish which kind of big one it belongs to.

The basic reasons are as follows:

1.Lack of power, mechanical watches are divided into manual mechanical watches and automatic mechanical watches, insufficient power is an important reason for the watch to slow down or stop the watch, manual mechanical watches can be wound directly when they are slow, and the reason why automatic mechanical watches are slow is mostly because of insufficient wearing time or the arm does not maintain a normal amount of exercise, and it can be directly manually wound to supplement the power.

2.There is no maintenance, mechanical watches are generally maintained once every 4 to 5 years, the watch is used for a long time, the lubricating oil in the movement will dry up, and the friction of each gear will produce iron filings for a long time, increasing the friction between the gears, this problem only needs to clean the movement and re-refuel.

3.The mechanical watch has a complex structure, which is composed of hundreds of precision parts, which is very fragile, and the watch is subjected to a strong impact, and the parts in the movement may loosen and cause the watch to slow down or stop watching. According to the reason for the slowness of the watch, you can take corresponding measures, pay attention to the winding of the manual machinery, maintain the normal amount of exercise of the automatic mechanical arm, maintain it on time, pay attention to the waterproof, shockproof and anti-magnetic of the watch, and send it to a professional maintenance center for repair in time if there is a problem.

Shock: A mechanical watch has a complex structure and is composed of hundreds of precision parts, which is very fragile, and the watch is subjected to a strong impact, and the parts in the movement may loosen and cause the watch to slow down or stop. According to the reason why the watch is slow, you can take corresponding measures, pay attention to the winding of the manual machinery, maintain the normal amount of exercise of the automatic mechanical arm, maintain it on time, pay attention to the watch waterproof, shockproof and anti-magnetic, and send it for repair in time if there is a problem.

Reasons for the watch to stop:

1.Watch magnetization: The watch is in too much contact with items with magnetic fields, which leads to the phenomenon of magnetization of the watch, causing the watch to be inaccurate.

After being magnetized, the watch may stop, slow, or fast. After the watch is magnetized, its magnetism will not recede on its own, and it needs to be demagnetized to restore it to normal.

2.Lack of maintenance: If the watch lacks maintenance, it will lead to wear and tear of parts, dry up the sludge, affect the normal running time of the watch, and make the watch appear fast and slow.

3.Mechanical failures: Mechanical failures such as watch balance spring failures, escapement failures, and component slips can cause the watch to be fast and slow.

Mechanical watches are sometimes fast and sometimes slow, and it may be caused by severe impacts, water ingress, etc. Quartz watches are generally very accurate and less prone to time failures. In the case of adequate maintenance, it is more likely to be fast and slow, which is more related to the failure of the circuit board, or the poor contact of a certain part.

It is recommended to go to a regular after-sales center to deal with it! Room 602, 6th Floor, Block W3, Wangfujing Oriental Plaza, Beijing.