What is the reason for the stealing of a Breitling watch?

Hello, glad to answer for you!

The main reasons why the watch does not go are the misalignment of the core gear, the magnetism of the watch, bumps, and the long shelving time, and the oil sludge is dry. The most common reason for the failure of the watch not going is the lack of power of the watch and the movement of the watch does not work.

When the mechanical watch suddenly stops, the priority is to think about whether it is caused by lack of power. Hand-wound watches should be wound at the same time every day as much as possible so that the watch can operate with sufficient energy for the next 24 hours.

If the watch is used for a long time, then its wear and tear will be more serious, and the external maintenance of the watch will be easily damaged. It is necessary to regularly replace the watch you are wearing, and it is necessary to maintain the watch regularly, for the service life of your watch, it is better to maintain it regularly.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. These will cause the watch not to go, and you need to go to a professional repair center for testing and processing.

If there is a problem with the watch, it is better to send it to the watch after-sales center for maintenance as soon as possible. Wanling Hui has an after-sales service, don't go to those small repair shops for maintenance. Not only are they not empowered, but their technology is not professional enough.

The instruments are not very sophisticated. **It's also misreported. It will also cause the watch to be out of warranty.

Mechanical watch stealing may be caused by insufficient power, wearing time is too short, hairspring failure or parts failure, etc., wear the mechanical watch correctly to reduce the occurrence of failure, if there is a problem to repair as soon as possible.

Mechanical watches will stop secretly, sometimes it is not really damaged and need to be repaired, understand the reasons that cause mechanical watches to stop secretly, and save the trouble of maintenance.

1.Lack of power. A hand-wound mechanical watch is powered by the mainspring in the movement, and if the power is insufficient, it will stop secretly, so in this case, it can be restored by manual winding.

2.Wearing time is too short. The principle of movement of the automatic mechanical watch is that when the arm swings, it will drive the movement to circle around, and the purpose of automatic winding can be achieved by swinging the arm, if the wearing time is too short, can not be wound or the winding is not enough, there will be a sneak stop, you can take off the watch and shake horizontally for about 3 minutes to provide power for the winding, usually pay attention to let the watch and wrist stay as much as possible for 6 8 hours.

3.Hairspring failure. When the amount of activity is too large, the clockwork will be too tight and cause the upper mechanism to malfunction, which usually occurs between 9 and 12 o'clock at night, and is prone to calendar jamming.

4.Failure of parts. There are many parts in the watch, if the watch is bumped, maybe there is no abnormality on the surface, but there are parts inside that are damaged or fall off, which will make the watch stop secretly.

The hairspring is stretched and curled in the work, at the moment of stretching, it happens to encounter an external impact force, and the hairspring acts with an external force, and the outer wheel of the hairspring is quickly stuck on the needle clamp, or stuck on the outer pile pin of the movable outer pile ring.

After the hairspring is subjected to external impact and vibration, it may cause the fast and slow needle to rotate and rotate, and the action length may change.

In the case of a newly purchased watch or a watch that has been cleaned and oiled for a short time, the balance spring is partially fixed and the working length is shortened due to oil leakage due to over-lubrication or incorrect injection.

Working in or out of a large magnetic field, accumulating over a long period of time, the hairspring, etc., are magnetized and overlapped on each other, resulting in a complete stop of the watch.

When the watch encounters the situation that it does not run accurately, there is no need to worry, go to the watch maintenance agency in Room 2606, Block B, China Resources Building.

Lack of power: Generally, the self-winding mechanical watch uses the movement of the human arm to complete the winding, but if the watch is parked for too long or because the person wearing the watch has little activity every day, it will cause the watch to be unwinded, the power is not enough, and the formation does not go.

In particular, there are deficiencies in the design of some watches that are self-winding. This problem is even more prominent. Mechanical parts failure:

If there is no problem with the power, it may be that there is a problem with the mechanism of the watch. Some people wear watches for a long time without washing oil and maintenance, and there are a lot of dust, oil stains, and rust in the movement, resulting in small debris, and sometimes the gears will be stuck by small debris and will stop secretly.

There is also how well the winding mechanism works (rotor, reverse, clockwork). Then there is whether the watch has been dropped or subjected to large vibrations, which causes the watch to stop and go. 3. How to prevent the watch from stopping secretly.

Quartz watch prevents stealing: replace the new battery in time when the watch battery is low. Avoid strong collisions during the use of the watch.

On the one hand, it may be a lack of power and a few minutes of stealing; On the other hand, it is possible that there is something wrong with the hairspring; If you stop while skipping the calendar, it may be that the skipping part is damaged or stuck. If the mechanical watch is not powered enough, as long as it is fully wound in time. If there is a problem with the internal parts of the movement, it must be sent to a professional repair center for repair.

The reason for the mechanical watch to stop.

1) Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. Automatic watches, in particular, are inefficient and require a lot of arm movements.

When typing on a keyboard, the range of motion of the wrist is too small, and the winding efficiency is very low. If the amount of movement is small, you can use the winding method of the mainspring manually.

2) Gear failure: Eccentric wheel, center wheel failure and other gear train failures will lead to manual stop of the watch. Table stealing can also be caused by the collision of the pallet fork and the fork clamp, the collision of the outer pile or the outer clamp of the swing beam and the balance spring, the deformation of the fork head of the pallet fork and the collision of the impact plate, or the collision of the fork head nail and the disc nail.

These situations are often difficult to spot and require careful inspection and testing to identify and solve problems.

3) Lack of maintenance: mechanical watches, it is best to maintain every 2-3 years or so. If it is used for a long time without maintenance, a large amount of oil sludge will be produced and deposited in it. The friction between the gears increases, which causes the gears to slip.

Reasons for the watch to stop:

1.Watch magnetization: The watch is in too much contact with items with magnetic fields, which leads to the phenomenon of magnetization of the watch, causing the watch to be inaccurate.

After being magnetized, the watch may stop, slow, or fast. After the watch is magnetized, its magnetism will not recede on its own, and it needs to be demagnetized to restore it to normal.

2.Lack of maintenance: If the watch lacks maintenance, it will lead to wear and tear of parts, dry up the sludge, affect the normal running time of the watch, and make the watch appear fast and slow.

3.Mechanical failures: Mechanical failures such as watch balance spring failures, escapement failures, and component slips can cause the watch to be fast and slow.

Mechanical watches are sometimes fast and sometimes slow, and it may be caused by severe impacts, water ingress, etc. Quartz watches are generally very accurate and less prone to time failures. In the case of adequate maintenance, it is more likely to be fast and slow, which is more related to the failure of the circuit board, or the poor contact of a certain part.

It is recommended to go to a regular after-sales center to deal with it! Room 602, 6th Floor, Block W3, Wangfujing Oriental Plaza, Beijing.

[Watch maintenance and repair can refer to the service center to go to 702, Xidan Joy City Office Building, Xicheng District, Beijing] to provide Swiss watch strap customization, cleaning and maintenance, identification, refurbishment, fault repair, watch appearance and replacement of damaged parts, strap replacement services. Our technicians have undergone strict professional skills training and provide two years of after-sales guarantee services. The service center is guided by the watch manufacturer on the spot**, **transparent, no hidden consumption, no additional charges.

A simple mechanical watch is winded, the mechanical watch does not go when the first consideration of the clockwork is not enough, as long as the spring is full, as shown in the figure on the button on the edge of the mechanical watch, clockwise rotation of the button on the side of the clockwork, there is a magnetic sound, usually 30 times rotation means that the spring is full.

There is a roulette wheel in the automatic mechanical watch, which is driven by the rotation of the human wrist, the user must wear it every time, and have a certain amount of wrist activity.

There is also the quality problem of the watch or the long-term use of the parts is not good, the movement needs to be re-cleaned and oiled, you can go to the mechanical watch maintenance center, find a professional maintenance person to solve.

Hello, glad to answer for you!

Reasons for inaccurate time: insufficient kinetic energy reserve of the watch, insufficient battery of the watch, the watch has been hit or hit by an external source, the watch has not been maintained for a long time, and the watch is affected by magnetic fields.

Solution: It is necessary to go to the after-sales center for testing and maintenance.

Hello, the phenomenon of stealing stops in general mechanical watches may be.

1.Insufficient power: mechanical watches are divided into manual mechanical watches and automatic mechanical watches, insufficient power is an important reason for the watch to slow down or stop the watch, manual mechanical watches can be wound directly when slow, and the reason why automatic mechanical watches are slow is mostly because of insufficient wearing time or the arm does not maintain a normal amount of movement, and it can be directly manually wound to supplement the power.

2.No maintenance: mechanical watches are generally maintained once every 2 to 3 years, the watch is used for a long time, the lubricating oil in the movement will dry up, and the friction of each gear for a long time will produce iron filings, increase the friction between the gears, this kind of problem only needs to clean the movement, re-refueling.

3.Shock: A mechanical watch has a complex structure and is composed of hundreds of precision parts, which is very fragile, and the watch is subjected to a strong impact, and the parts in the movement may loosen and cause the watch to slow down or stop.

According to the reason why the watch is slow, you can take corresponding measures, pay attention to the winding of the manual machinery, maintain the normal amount of exercise of the automatic mechanical arm, maintain it on time, pay attention to the watch waterproof, shockproof and anti-magnetic, and send it for repair in time if there is a problem.

There are many reasons for this, such as: collision, fall, magnetism or dissatisfaction with the upper bar, etc. It needs to be determined by professional technicians and professional testing equipment. During the warranty period, it is recommended to contact the brand after-sales service as soon as possible.

Problems that should be paid attention to when wearing the watch: 1. During the wearing of the watch, the waterproof ring should be avoided due to large temperature changes, so it should not be used in hot baths, saunas, large amounts of water vapor and environments with drastic changes in temperature and humidity. 2. Do not operate the buttons and adjust the crown of your Jaeger-LeCoultre watch in water, as the purpose is to prevent water from entering through the gaps and corroding the movement.

In normal use, the non-screw-down crown should be pressed back into its original position and the threaded crown should be screwed down. 3. The appearance of the watch should also be cleaned regularly, such as the case, strap, etc. It is recommended to go to a repair shop for cleaning and maintenance, never leave the watch in water for a long time, wash it by soaking, and try to avoid direct contact with water.

4. Avoid exposure to the sun to prevent fading and deformation. At the same time, it is also recommended to avoid contact with water, moisture, cosmetics, and other items containing chemical ingredients to prevent reactions, and it is recommended that you change the watch strap regularly. 5. When taking off the watch, it must be placed in the packaging box or in a safe position, and it should be avoided from being bumped, and avoid contact with solid objects such as quartz crystal, grinding stone, sandpaper, granite surface, and concrete wall.

There is a high probability that the watch is stopped because the watch's battery is out of charge and needs to be replaced.

One is due to the lack of power, and the other is due to the failure of mechanical parts. Generally, a self-winding mechanical watch uses the movement of the human arm to complete the winding. But if the watch is parked for too long, or because the person wearing the watch does not move much every day!

Due to the lack of movement, the watch is not winded, the power is not enough, and the formation does not go! Especially for some watches that have shortcomings in the design of automatic winding, this problem is even more prominent! In case of such problems, the only way to solve this problem is to extend the wearing time appropriately, or to solve it by manually repairing the chain.

If there is no problem with the power, it may be that there is a problem with the mechanism of the watch. Some people wear the watch for a long time without washing the oil for maintenance, and there are a lot of dust, oil stains, rust, and small debris in the movement. Sometimes the gears will get stuck in small debris and stop secretly!

There are also whether the hands of the watch (hours, minutes, seconds) are stuck or not, and whether the winding mechanism is running well (rotor, reverse, mainspring). Then there is whether the watch has been dropped, and it has been subjected to a large vibration, which causes the watch to stop and go, so it is necessary to ask the watchmaker to repair and maintain it.

Since it is normal for a mechanical watch to stop secretly, does it need to be repaired? This should be judged, after all, there is a reason for the watch to stop secretly, if it is normal under normal circumstances, it will not be stopped. We can first pay attention to the frequency of your watch stealing stops, if the frequency is not high, once or twice, the cousin can not waste this money, if the frequency is high and affects the time, you need to repair.

"The watch is related to problems such as watch stoppage, watch bumps, and hairspring failures. Watch steal stop is when the watch has enough power, the watch stops, and after a period of time it starts to move again, so that the watch will slow down, that is, the watch steal stop phenomenon.