Do I need to start the car during the lighting simulation of driving test subject 3?

Subject 3 exams.

The vehicle needs to be started before the lights can be simulated.

The lights can only be used when the vehicle is started.

Subject 3, also known as the road test, is a motor vehicle driver's license.

Part of the assessment is the abbreviation of the road driving skills and safe and civilized driving knowledge test subjects in the motor vehicle driver test. The main use of lights includes:

1. If you are about to turn at an intersection, please use the correct lights (alternate high and low beams not less than 2 times) 2. If you are driving on a low visibility road, please use the correct lights (turn on the high beams) 3. If you are going to pass through a sharp bend, please use the correct lights (alternate high and low beams no less than 2 times) 4. If you are going to pass through a slope, please use the correct lights (alternate high and low beams no less than 2 times) 5. If you are going to pass an arch bridge, please use the correct lights (alternate high and low beams no less than 2 times) 6. If you are going to cross a pedestrian crossing, use the correct lights (alternate high and low beams no less than 2 times).

7. There are no traffic lights to be passed.

At the intersection under control, please use the correct lights (alternate high and low beams no less than 2 times) 8. If you are about to overtake, please use the correct lights (turn on the left turn signal first, then alternately use the high and low beams no less than 2 times, and then turn on the right turn signal).

9. If you are going to meet other vehicles, please use the correct lights (turn on the low beam) After the lighting simulation is completed, the candidates need to turn off the lights and proceed to the next test.

Light the fire. But most of the test rooms have already started for you, so you don't need to click anymore.

Subject 3 exam: If you light the fire before the simulated lighting, how to take the exam without igniting the fire.

Exam content of Subject 3:

1. Including getting on the car to prepare, go around the car counterclockwise, fasten the seat belt when you get in the car, turn on the left turn signal, hang up the gear, release the brake, and press the horn;

2. Starting, driving in a straight line, adding and decreasing gear operations, changing lanes, pulling over, going straight through intersections, turning left at intersections, turning right at intersections, passing pedestrian crossing lines, passing school areas, passing bus stops, meeting cars, overtaking, U-turning, and driving at night;

3. The mileage of the small car test is not less than 3 kilometers, and no less than 20% of the candidates are taken for the night test.

Subject 3

Subject 3, also known as the road safety driving test, is a part of the motor vehicle driving license assessment, and is the abbreviation of the road driving skills and safe and civilized driving common sense test subjects in the motor vehicle driver test. The content of the road driving skills test is different for different types of prospective vehicles.

The content of module 3 generally includes: preparation for getting on the bus, light mock test, starting, driving in a straight line, adding and decreasing gears, changing lanes, pulling over, going straight through the intersection, turning left at the intersection, turning right at the intersection, passing the pedestrian crossing line, passing the school area, passing the bus stop, meeting the car, overtaking, making a U-turn, and driving at night.

The content of the safe and civilized driving knowledge test includes: safe and civilized driving operation requirements, safe driving knowledge under bad weather and complex road conditions, emergency handling methods such as tire bursts, and disposal knowledge after traffic accidents.

Hello, subject 3 simulates the night driving lights need to be ignited first, and then turn on the lights, because some vehicles are not ignited, and some lights are not working properly. I hope mine can help you, thank you.

Hello I'm glad to be able to answer for you I'm Xiaoxue Teacher As far as I know, it should be needed, and I personally think it's needed, because only when you start the car, the various parts on the car can start to run normally, so when the subject three lights are planned to start, you need to start the car.

Questions. Can you tell me about all the steps before you get started?

Tomorrow it's an exam and I forgot.

1. Preparation for getting on the bus 1. When the test begins, students should make preparations before the test, mainly: adjust the seat (clutch step to the end, adjust the seat), adjust the left and right rearview mirrors, complete the light reset, and then turn off the vehicle. 2. The light reset mainly depends on these aspects:

Check that the light switch is off; The left and right direction lights are off; The pole is the low beam position. 3. Listen carefully to the voice command, when you say "please start getting on the car and prepare", you have to get out of the car and go around the car counterclockwise and press four buttons. It must be counterclockwise!

And when observing, you should also observe whether there is a problem with your vehicle, whether there are obstacles around, etc. 2. Prepare for the test and get on the bus again, fasten your seat belt first, check whether the dashboard and gear are in neutral, etc. Press the clutch to ignite (start the engine).

Note: If you fail to fire with a stopper, you must fire in neutral.

Questions. Get in the car and adjust the seat, turn on the power and press the button around the car, and when you return to the car to simulate the lights, do you want to start the car?

Under normal circumstances, the third branch doesn't have to start the car by himself.

I didn't even start the exam on my own.

Hello, you can ask the coach for such a professional question, hurry up and study before the exam, I wish you success in the exam and pass it smoothly.

The order of the lighting exam is generally as follows:

1. The following will be a test that simulates the use of lights in night driving scenes, please follow the voice command to make the corresponding light operation within 5 seconds.

2. When driving at night without street lights and poor lighting, please change the headlights to high beams.

3. When meeting non-motorized vehicles on narrow roads at night, please change the headlights to high beams.

4. Follow the car in the same direction at night or drive in foggy weather, please turn off all lights after the completion of the simulated night test, and please start to continue to complete the test.

The operation of the lamp in subject 3 is as follows:

1. Headlights need to be turned on when driving at night without street lighting or under poor lighting conditions.

2. At night, you need to turn on the low beam when meeting with non-motorized vehicles on narrow roads and narrow bridges.

3. Pass through sharp bends, pedestrian crossings or intersections without traffic signal control at night. It is necessary to alternate high and low beams (change the light more than twice).

4. It is difficult to move when there is a breakdown on the road or a traffic accident at night, which hinders the traffic. The operation converts the headlight into a width indicator light plus a warning light.

5. Driving in foggy days requires turning on fog lights and warning lights.

6. At night, the driving in the same direction at close range is converted into low beam.

7. If you are going to pass through a sharp bend, please alternate the high and low beams no less than 2 times.

8. If you are going to pass through the slope, please use the high and low beams alternately no less than 2 times.

9. If you are going to pass through the arch bridge, please use the high and low beams alternately no less than 2 times.

10. Convert the lights into low beams when meeting with motor vehicles at night.

1. Simulated lighting**:

At the start of the exam, after successful fingerprint verification, the following voice simulating lights will be heard first:

The following test will simulate the lights of driving at night, please make the corresponding light operation within 5 seconds, please turn on the headlights;

1. Turn on the light, and the light is low beam at this time, as shown in the following figure:

The instrument panel shows the following picture: This is the low beam.

2. At night, there are no street lights, and the driving (high beam) instrument panel is displayed under poor lighting conditions as shown in the following figure, which is the high beam.

3. Meet non-motorized vehicles on narrow roads and narrow bridges at night (low beam) or: follow the car in the same direction at night (low beam).

In this question, you only need to lift the light lever up again and change the high beam to the low beam.

4. Please change the headlamp to high beam (high beam) and lift the light lever again.

5. Meet the motor vehicle at night (low beam).

Or: meet a non-motorized vehicle on a narrow road or bridge at night (low beam) or follow a car in close range in the same direction at night (low beam).

In this question, you only need to lift the light lever up again and change the high beam to the low beam.

Note: If question 4 does not appear, then question 5 will not appear again, and it will be this question directly

When crossing sharp curves, slopes, arched bridges, pedestrian crossings, or intersections without traffic light control at night (this question will be taken separately) (alternating between near and far). It is also the only problem that requires the light lever to be lifted twice in a row.

Driving at night without street lights and in poor lighting conditions.

Correct operation: Turn on the headlights (high beam mode).

Meet the car at night.

Correct operation: Turn on the low beam.

At night, through sharp bends, slopes, arched bridges, pedestrian crossings, or junctions that are not controlled by traffic lights.

Correct operation: Use high and low beams alternately.

Convert the headlights to high beams.

Correct operation: Turn on the high beams.

Follow the car in close proximity in the same direction at night.

Correct operation: Turn on the low beam.

Crossing an intersection that is not controlled by a traffic light at night.

Correct operation: alternate use of high beams.

Driving in foggy weather. Correct operation: Turn on the fog lights.

Breakdowns on the road at night make it difficult to move because it obstructs traffic.

Correct operation: Turn on the hazard warning flash.

Listen to the voice to turn on the headlights;

Turn on the high beams when driving at night;

Turn on the low beam at night;

alternate use of high and low beams at night in sharp bends, slopes, etc.;

Listen to the voice to turn on the headlights and change them into high beams;

Turn on the low beam when following the car at close range at night;

Turn on the fog lights and emergency lights in hazy weather;

In the event of a malfunction at night, the width indicator light and emergency light are turned on;

At the end of the test, all the lights are turned off.

If you lose points for lighting items, you have to plan for other items, in case other items deduct points, do a few more mock lighting exams, and simulate a few more times where something goes wrong

If I hadn't met in my life, I would still be the same person, dreaming occasionally, and then, day after day, the sea would not be in this noisy city. I won't understand that there is still such a thing in this world.

There will be a reminder in the test system. There are 6 questions in total.

Hello subject! Based on your question, the following is my personal opinion, and I think you can just follow his instructions.

According to the prompts, the corresponding lighting operation can be completed within the specified time.

Driving at night without street lights and in poor lighting conditions" (reacts within 5 seconds), then we turn on the light switch and <>

(Because there are several sets of orders when the use of the lights, I will not introduce them in order, only tell you about the use of a few lights, as for the voice of the lights, the following will be introduced. No hurry, no hurry).

2. Please change the headlights to high beams.

Subject 3: Start the fire first. Needless to say, if the car is not started, the lights cannot be used, so the lighting simulation cannot be carried out. In addition, even if you don't know, after getting into the car and adjusting the seats, mirrors, fastening seat belts, etc., the voice announcement will also prompt you to start the engine first, and then broadcast "Let's start the test of using lights in a simulated night driving scene".

Notes:It is worth noting that it is best to check whether the lights of the car have been reset before ignition, if they are not reset, it is possible to fail the test after starting the lighting simulation. So before starting the exam, check that the switch on the light lever is in the off position.

Subject 3 is to prepare for getting on the bus, not to do simulated lighting first. You need to make corresponding operations according to the voice prompts in the car, and I will give you a specific introduction to the requirements for the old test prepared for subject 3.

Candidates are required to follow the instructions of the safety officer, approach the vehicle, go around the vehicle (from the left front door backwards), and open the door to get on the bus after confirming safety. After getting on the bus, you hear the voice prompt "Please prepare for the exam, dress up and do fingerprint verification", first adjust the seat to the right position for you, adjust the inner and outer mirrors, and fasten your seat belt. Then do the fingerprint verification.

The fingerprint scanner is located on the left side of the steering wheel under the air conditioning vents.

Yes, start the car and change the lights.

Of course, this is needed, because he can only work properly after starting the car. In other words, all parts of the machine are running normally at this time, otherwise if you don't start the car, then it will be in a stopped state. So to say that, his backstage, to put it mildly, her backstage data will not be displayed in any way, not to mention that he also needs the car itself to provide a certain amount of energy power.

Personally, I think it is necessary, because only when you start the car, the various parts on the car can start to run normally, so when the subject three lights are intended to start, you need to start the car.

You need to start the car, and when you take the third subject, you will simulate the lights during normal driving.

This is a must, start the car first, then listen to the voice broadcast, and take the light test.

This is definitely required, and only the starting car subsystem will recognize that you are taking a mock test.

After the car starts, the lights are simulated.

The engine needs to be turned before it can be operated, and the power is off.

Start the fire first. Part of the module 3 motor vehicle driver's license examination, the motor vehicle driver is tested in the middle of the road. The content of prospective driving is different, and the road driving skills test is not the same.

The content of subject 3 roughly includes: vehicle preparation, lighting simulation assessment, starting, driving in a straight line, gear addition and subtraction operation, lane change, pulling over, going straight through the intersection, turning left at the intersection, turning right at the intersection, crossing the pedestrian crossing, passing the school campus, passing by the bus stop, meeting, overtaking, making a U-turn, and driving at night.

Safe and civilized driving operation requirements, with safe driving knowledge in bad weather and complex road conditions, as well as safe driving knowledge in emergency situations such as puncture. How to deal with traffic accidents and how to deal with them.

Precautions: 1. Prepare for the road test.

Candidates should follow the instructions of the security guards, approach the vehicle, walk around the vehicle (from the left front door to the rear door), confirm that it is safe, and open the door of the car. When you get on the bus, you will hear a voice prompt that says "Please prepare for the test and get your fingerprint verified". First, adjust the seat to adjust your position, adjust the interior and exterior mirrors, and fasten your seat belt.

Then fingerprint verification. The fingerprint reader is located on the left side of the steering wheel, under the air conditioning vents.

2. Driving at night:

After successful fingerprint verification, students will hear a voice prompt before taking the daytime exam: "Now start simulating the use of a night light." "Please follow the voice prompts and the candidate should start the lighting operation.

In the Night Driving Lights Mock Test, three items will be randomly selected from the following items for examination. I touch it.

Photo by Tong Fei) NIO ES8 NIO ES6 Wenjie M5 NIO EC6 Xpeng P7 Trumpchi GS8 @2019