How can the oil filter ring be unscrewed Why does the oil filter seal be disconnected?

Hello friends, to be exact, when installing the oil filter element, you should apply oil on the sealing ring of the oil filter element, if you don't apply the oil will be broken, I hope my can help you, if you still have any questions, you can contact me at any time. BBA Mercedes-Benz BMW Audi Maintenance wishes you a happy life, all the best, and a lot of money!

Hello car owner, I am happy to answer for you, the oil grid is generally divided into two kinds of paper filter and iron filter. The first thing to determine is the oil bar of your car. If it is a paper filter, it should be that the sealing ring is not installed in place or the quality is problematic or the sealing ring has not been replaced.

If it is an iron oil grid, it should be too tight or the quality is too strong.

It's a seal. material issues, tensile strength.

Not enough, not qualified. Excessive pressure is not the cause of breakage, and these factors should be considered when making a filter cleaner.

In addition, if the sealing ring has been used for too long, it may have been corroded and aged.

Then there is the installation operation error, which is too tight, resulting in the fracture of the sealing ring.

Today's products are all produced on the assembly line, and problems will inevitably occur. Some will be tested, and some may end up in the market. The probability of 1 in 100,000 is already close to 0, and no company dares to protect 100% of the product.

Make sure you have enough oil in your engine. Pay attention to replacing the filter element, the sealing ring of the filter element should be coated with oil first, not too hard to screw, and then use a wrench after tightening it by hand.

Twist 3 4 turns, which is 25Nm torque, and pay attention to the quality of the filter element. The paper filter element is only equipped with a sealing ring, which is installed on the top of the outer cover, and there is no sealing ring inside, and the outer cover is not equipped with a sealing ring or does not replace, which will lead to oil leakage; The sealing ring on the outer cover must be smeared with oil on the sealing ring, otherwise it is easy to damage the sealing ring, and the sealing ring is to let the oil filter through the filter paper, if the sealing ring is not installed, it will generally not affect the oil pressure, but some of the oil will not be filtered by the filter paper, it is recommended to contact the customer as soon as possible, with a false impression to tell the last batch of filter paper that there is a problem, and replace the filter paper for free, If you don't use the oil for too long, the impurities will cause the oil passage to be blocked

The reason for the breakage of the rubber ring in the installation of the iron oil filter element is improper installation and misalignment. Too much oil pressure causes frustration. Counterfeit and shoddy goods, caused by quality problems. The main reason is related to the oil pressure regulator. It's the quality of the oil filter.

What is the reason for the rubber ring broken when the iron oil filter element is installed?

The reason for the breakage of the rubber ring in the installation of the iron oil filter element is that the imitation forest is cracked due to improper installation and misplacement. Too much oil pressure causes frustration. Counterfeit and shoddy goods, caused by quality problems.

The main reason is related to the oil pressure and the regulator. It's the quality of the oil filter.

Hello with this filial piety, to your expansion as follows<> the role of the filter element, the filter element is a professional term in the filtration industry, in order to purify the original ecological resources and the reuse of resources, and the need for purification equipment, now the filter element is mainly used in oil filtration, air filtration, water filtration and filtration industry. The filter element separates solid particles from liquid gases.

The oil filter element is removed by screwing to the left, loosening to the left, tightening to the right, tightening clockwise, and loosening counterclockwise.

Clockwise is the direction in which the clock goes.

For a new filter, you don't need to fill the filter with oil first.

Hello, according to what you said about this situation, the replacement of the oil filter element, the sealing ring is broken, which means that the quality itself is a problem or the repair of the screwing force is too much caused by this situation, this situation is recommended not to drive, need to stop and shut down the engine immediately, so as not to cause engine damage, find a trailer or find a maintenance worker for maintenance I hope this service can help you, if it helps you, look forward to your praise and attention. The car master is here to help.

I just changed the oil filter, and the filter seal is broken.

Hello, according to what you said about this socks situation, the replacement of the oil filter element, the sealing ring is broken, which indicates that the quality itself is a problem or the repair of the screwing force is too much caused by this situation, this kind of land situation is recommended not to drive, need to stop and shut down the engine immediately, so as not to cause engine damage, find a trailer or find a maintenance worker for maintenance I hope this service can help you, if it helps you, look forward to your praise and attention. The car master is here to help.

My car arrived at the shop in the morning to do the maintenance just changed the hungry key oil, and then drove about 20 kilometers to leak oil, the reason is that the quality of the machine rolling source filter is not good, the sealing ring is broken, and then the faulty oil lamp is on after a few seconds, and then the engine has an abnormal sound, and then the bad car happened to go to the shop for maintenance, about 30 kilometers to change the filter, add oil, does this situation have an impact on the engine?

Now there is no problem with the engine without abnormal noise.

Found that the problem light was on to the repair shop to drive more than 10 kilometers, sometimes bright and sometimes not on, repaired a few kilometers without abnormal sound, when the repair was stopped for a while, now there is no abnormal sound there is no problem. If there is a problem with the engine, it will make a serious abnormal noise.

This is due to the fact that the oil filter was not tightened according to the specified torque when the oil filter was installed, or it could be caused by the absence of a hot car. Organic oil in the oil filter element. If there is no hot car, the viscosity of the oil is very large, which will also cause the oil filter element to be twisted and disturbed.

The oil filter element is an important part of the engine and is used to filter the oil. If there is no oil filter, the oil will be particularly dirty after a period of use, affecting the lubrication of the engine.

Engine oil is known as the blood of the engine. If there is no oil in the engine, the engine will not function properly.

Engine oil not only plays the role of lubrication in the engine, but also plays the role of cleaning, sealing, buffering, rust prevention and heat dissipation.

When the engine is running, the oil will form a layer of oil film on the surface of each part of the engine, which can avoid friction caused by direct contact between the parts in the engine.

If the parts in the engine are in direct contact and cause friction, it will exacerbate the wear and tear of the engine, and it will also cause a large amount of heat to be generated in the engine instantaneously.

This is fatal to the engine.

The performance of the engine oil will be reduced after a long period of use, so it is necessary to change the oil regularly.

If you don't change the oil for a long time, it will also increase the wear and tear on the engine.

Replace the oil filter element with each oil change.

Millions of car purchase subsidies.

Summary. Because there is no oil, the oil warning light will be on, if you stop in time and see the warning light stop, the engine will not be damaged, and the oil filter with screw rod falling is the reason for repairing the car.

Hello, this question can give you a perfect reply, wait for me to sort out the information, I'm typing, 2-3 minutes, don't finish.

Hello, I am your exclusive technician Yao Xindong, stupid, attentive, attentive to answer your car questions, for you to find the corresponding problem solutions and solutions! According to your description, this is a normal car like oh pro, not the reason for repairing the car oh pro, if you go down together, re-screw it on the closed friend Oh pro, this is a double-ended screw, screw it on it, it fell off during driving, and the engine was scrapped.

I must be the repairman's fault if I fell off while driving, but if the engine is scrapped and has nothing to do with the repairman, who should I go to for compensation?

This is a repair shop that can compensate you for a part. Only you bear part of it, dear, why do I have to bear part of it.

Because if there is no oil, the oil warning light will be on, if you stop in time and see the warning light stop, the engine will not be damaged, I am running on the high speed, I hear the sound of da-da-da, I immediately pull over.

Well, if this one drops, it will be damaged in less than a minute,

Installing two rubber rings is equivalent to screwing in less. It is easy to cause oil leakage or loosening at high pressure.

During the operation of the engine, metal grinding debris, dust, oxidized carbon deposits at high temperatures, colloidal sediments, water, etc., are constantly mixed with the lubricating oil. The oil filter element is not installed with impurities or particles are not filtered directly into the engine, which will accelerate the wear of the crankshaft, camshaft and bearing in the engine, as well as the lower part of the cylinder and the piston ring, the consequences are: large component clearance, increased oil demand, oil pressure drops, and the gap between the cylinder liner and the piston ring increases.

Engine oil and oil filter should be replaced about every 5000 kilometers, which is conducive to protecting the engine, reducing the failure rate, and not saving a small amount of money and losing a lot of money Oil filter: the last guarantee for the cleanliness of the oil.

Dizzy! Installing two rubber rings is going to be a big problem! If the oil pressure is high, the sealing ring will be swollen!

Cause oil leakage, replace it quickly! Or repair!

I've installed it once before, and as soon as the throttle increases, the oil pressure rises. The oil is immediately sprayed out of the oil grid.

What are the consequences of installing two rubber rings on the oil filter element, no big problem, I wish you a happy time!

Summary. Hello, I have seen your question and am sorting out the answer, please wait a while

Hello, I have seen your question and am sorting out the answer, please wait a while

Thank you for your question, good friends smile at night is the material problem of the sealing ring, the tensile strength is not enough, unqualified. Excessive pressure is the cause of breakage, and these factors must be taken into account when making filters. In addition, the sealing ring that has been used for too long may have been corroded and aged.

Then there is the operation error of the old rubber socks installed, and the tightening is too tight, resulting in the breakage of the sealing ring.

After doing the maintenance, I ran 400 kilometers and the oil leaked, and the sealing ring of the paper oil filter was broken, what was the reason?

It is the material problem of the sealing ring, the tensile strength is not enough, and it is unqualified.

Are you sure? It has nothing to do with the installation, if the installation is not good, will it leak oil at that time?

It should be, if it is not installed, it will immediately break the oil leakage.

If you don't install this, you will definitely not be able to do it immediately, and you won't run 400 kilometers to do this.

I told you, maybe it's a material problem with the sealing ring, the tensile strength is not enough, why are you so entangled if you are unqualified