What s the deal with the kettle light not working?

It may be that the metal sheet inside the electric kettle is in poor contact with the heater of the base, so the electric kettle cannot be heated normally, and the metal sheet and heater need to be reinstalled to ensure that the wiring is normal; It is also possible that the electric heater of the electric kettle is damaged and needs to be replaced with a new one.

The light is on, indicating that the whole machine is energized. Secondly, there are several reasons for not heating:1

The heating plate is damaged. 2.The thermostat or thermal fuse is damaged, causing the heating plate to not be energized.

3.The internal wiring is damaged, resulting in the heating plate not being energized.

1. The contact of the power socket is not good;

2. The contact between the two power contacts of the power base of the kettle is not good--- it is very likely;

3. The heating plate and the indicator light are --- bad at the same time, and the possibility is small;

4. It is possible that the circuit in the kettle is open --- the circuit;

5. The electric kettle switch is not --- possibility of electric power.

What is the reason why the kettle light is on and does not work The meaning of the light is on means that there is electricity, so it does not work when there is electricity. This indicates that there is a problem with the heating part. It takes a professional to check it out to know.

Hello! If the kettle light is not working, then the heating plate is not working, and it is best to replace it with a new one.

The "indicator light on" of the electric kettle means that the control switch is on, and there is no problem with the indicator light! If it doesn't work, the "heating plate" is damaged! It can be used by replacing the heating plate!

It may be because you haven't set it up, and you're using the kind of automatic setting, and you can click on the boil water function.

Either the light is broken or the pot is broken.

1. If the contact of the electric heating pipe is not good, damaged, etc., the electric heating pipe can be removed and the resistance value can be measured. If the electric heating pipe is not in good contact, you can disassemble the switch box to clean it, and then reconnect the electric heating pipe, but if the electric heating pipe has been seriously damaged, you can only replace it with a new electric heating pipe.

2. The switch of the main body of the kettle is faulty: if the switch here fails, it may also cause the light to be not hot. The solution to this problem is also very simple, if you open the main body of the kettle, if you see that the edge of the switch is partially melted and deformed, you can determine that the switch is broken.

Repair is also very simple, you can buy relevant standard parts to replace.

Precautions for the use of electric kettles.

The electric kettle is a high-power electrical appliance, read the manual carefully before use, and choose a proper power socket, and the socket needs to be used independently, and should not be used together with other high-power electrical appliances.

The power plug should be kept dry and clean, never showered with water, and should not be placed close to the fire source to avoid leakage or burning.

After the electric kettle is energized, do not pull the plug at will, you should wait for the automatic tripping, and then turn off the power to take water to drink after the heating is completed, in order to ensure safety, the electric kettle has no water, do not empty boiling, it is best to have someone to take care of it when using, but the person who takes care of it must not be a child, so as not to burn the bottle by the child.

1. The indicator light of the electric kettle is on, indicating that it is normal for the power supply to enter, but the heating core is burned out;

2. The electric kettle adopts a kind of appliance with intelligent steam induction control, overheating protection, automatic power-off when boiling water, anti-dry-boiling power-off, and rapid boiling of water;

3. The working principle of the electric kettle is as follows: the water vapor generated when the water boils to deform the bimetal sheet of the steam temperature sensing element, and the power switch is pushed by the lever principle by using the deformation, so that the electric kettle will automatically cut off the power after the water boils. It is not self-resetting when it is powered off, so the kettle will not automatically reheat after the power is off.

2. The contact between the two power supply contacts of the power base of the kettle is not good;

3. The heating plate and the indicator light are broken at the same time;

4. There is an open circuit in the circuit in the kettle;

5. The switch of the electric kettle is not electric, etc.

If you don't boil water, check whether the power socket and the heating base of the electric kettle are not in good contact, if the power socket is fine, it is likely that the power cord of the kettle is short-circuited or broken, and you can usually check whether the external circuit is broken in use, and then judge whether the heating wire is broken. If the heating chassis is broken, replace it directly.

The indicator light of the electric kettle is on, and the reasons why the kettle has not been hot may be as follows: 1. The indicator light is on indicating that the power supply is normal, and the main check is whether the heating tube is damaged, because the heating tube is the main heating component of the whole machine, and its damage must not be hot; 2. The terminal of the heating tube is connected or broken, resulting in the heating tube being unable to be heated without power; 3. There is a broken circuit between the connecting wire and the terminal plug of the heating pipe or an open circuit between the connecting wire and the coupler. Solutions to the above problems:

1. The heating pipe is damaged and cannot be replaced, so the heating pipe and base of this electric kettle are formed at one time and cannot be repaired; 2. The virtual connection of the heating tube terminal can be reconnected, and if it is broken, it can be repaired by spot welding machine welding; 3. When the connecting line is broken, it can be directly replaced with a new connecting cable. If the terminal insert is damaged, replace the insert directly, and if the terminal on the coupler is damaged, replace the coupler directly according to the original model.

The reasons why the kettle light is on and do not boil water are as follows:

1. When in use, if the power switch is normal, the fault mostly occurs in the insulation switch. First of all, see whether the reed of the bimetal sheet is pressed against the switch contact rod, if it is pressed too tightly, you can use tweezers to bend it upwards until the distance between the two reaches 1mm. If the distance between the bimetal sheet and the switch contact lever is normal, the switch box and reed should be disassembled.

2. In some cases, the indicator light is on, indicating that the power supply has been added to the indicator circuit, which is also very important. The fault is in the electric heating pipe or its connecting part, and it is common for the electric heating pipe to be damaged and the contact is poor. Remove the electric heating pipe and measure its resistance value.

The electric heating pipe is damaged and can generally only be replaced. The poor contact is mainly due to the serious corrosion or deformation of the contact reed in the power plug assembly, and it is best to replace it with a new one if the damage is serious.

3. When at home, the indoor power supply line or plug socket is not in good contact, and it should be eliminated first. It is also inevitable. Then check whether the electric heating pipe is seriously fouled, whether the contact between the base and the power plug holder of the pot body is seriously bad, etc.

If the electric heating pipe is fouled, you can scrape it with a knife first, and then polish it with fine sandpaper. If the contact between the base and the power plug seat of the pot body is seriously poor, the contact piece and the contact oxide layer of the plug holder can be cleared first, so that the contact between the two is close and good.

4. The amount of water inside the kettle should also be controlled, try not to exceed the highest water level that the kettle can hold, otherwise the water is very likely to overflow to the outside of the kettle when it is boiling. Also, be sure to fill the kettle with the right amount of water before you can turn it on to avoid burning the electric kettle.

It's the electric heating pipe that's broken.

Generally, the electric kettle is broken, usually the temperature control is broken, or the temperature control fuse is blown out, which can be detected by the multimeter resistance. If the contact is poor, it is mainly due to the serious corrosion or deformation of the contact reed in the power plug assembly, and the switch box can be disassembled for cleaning and repair, and the damage is serious to replace with a new one.

The electric heating pipe at the bottom of the electric kettle is brazed with the bottom of the kettle, this material is an aluminum alloy brazing solder welded together by high temperature, it is impossible to disassemble it, if it is a problem with the electric heating pipe, then it is only scrapped, in general, the electric heating pipe is difficult to break, you can use a multimeter to detect the leads at both ends of the electric heating pipe to see if there is resistance, if there is no resistance, it is the electric heating pipe is broken.

If you disassemble it, you can still do it, and the solder will melt away through the 680 high temperature, and then you can take it off while it is hot. It is best to take the appliance for repair and give it to a professional master for replacement.

2. The contact between the two power supply contacts of the power base of the kettle is not good;

3. The heating plate and the indicator light are broken at the same time;

4. There is an open circuit in the circuit in the kettle;

5. The switch of the electric kettle is not electric, etc.

The electric kettle does not heat, first of all, it is necessary to determine the reason for not heating, there are several reasons why the electric kettle does not heat:

1.The heating plate is damaged.

2.The thermostat or thermal fuse is damaged, causing the heating plate to not be energized.

3.The heating plate is not powered on due to damage to the internal wiring.

If it is the first type, there is no need to fix it; The second and third types can be considered, but they must be replaced with the same specification.

If the indicator light of the electric kettle is on, it means that the power cord is fine, either the metal sheet in the base of the electric kettle is in poor contact with the electric heater, or the electric heater is damaged, but generally the fault is caused by poor internal contact, you can remove the base screw with a driver, you can open the base panel, and then unscrew the fixing screw in the base, remove the small screw in the middle of the removed base, you can see the contact surface between the metal sheet and the electric heater, and the metal sheet will change color if the contact is generally poor. If it is normal, you can use a multimeter to measure whether the electric heater is good, if it is damaged, you can buy a set in the electrical market and reinstall it.

If the kettle indicator light is not lit, do not boil water, teach you a trick, and a toothpick can fix it.

Disassemble and check whether the switch is broken, second, the heating wire is broken, and it is generally less than 30 yuan to go to the repair shop to replace it.

The electric kettle has a circuit diagram, and a little electrician foundation can be repaired, and it is estimated that the heating pipe is broken.

Summary. Hello! The reasons and solutions for the heating of the kettle lamp is not lit, 1. The main circuit is not connected, you can use the multimeter to check whether the kettle base and power cord are normal, usually the base is damp, the contact is oxidized and rusted, and the contact is not connected; 2. Check the switch assembly, mainly check whether the main power plug of the switch assembly is normal.

The switch assembly is in the handle, because it is often at high temperature, it will cause the plastic at the plug of the main power supply to melt, the contact displacement of the switch, and the power supply can not be connected, resulting in the indicator light is not lit, and the heating plate has no electricity, so it can not be heated, in this case, a switch assembly can be replaced; 3. If there is a problem with the power cord, you can replace the power cord. 4.If there is a problem with the switch, the common reason is that the temperature sensor is seriously deformed or the switch connecting rod is blocked.

For the former, the angle of the temperature sensor can be rebent so that it can push the switch connecting rod normally. For the latter, it is necessary to find the obstructed part or foreign body, which can generally be restored to normal by removing the foreign body and correcting the position. 5.

If the power switch is normal, the fault mostly occurs in the insulation switch. First of all, see whether the reed of the bimetal sheet is pressed against the switch contact rod, if it is pressed too tightly, you can use tweezers to bend it upwards until the distance between the two. If the distance between the bimetal sheet and the switch lever is normal, the switch box should be disassembled, and the contacts and reeds of the insulation switch should be cleaned and repaired.

Lights do notBright also heats.

Hello! The reasons and solutions for the heating of the kettle lamp is not lit, 1. The main circuit is not connected, you can use a multimeter to check whether the kettle base and power cord are normal, usually the base of the kettle is damp, the contact is oxidized and rusted, and the power supply is not connected; 2. Check the switch assembly, mainly check whether the main power plug of the switch assembly is normal. The switch assembly is in the handle, because it is often at high temperature, it will cause the plastic at the plug of the main power supply to melt, the contact displacement of the switch, and the power supply can not be connected, resulting in the indicator light is not lit, and the heating plate has no electricity, so it can not be heated, in this case, a switch assembly can be replaced; 3. If there is a problem with the power cord, you can replace the power cord.

4.If there is a problem with the switch, the common reason is that the temperature sensor is seriously deformed or the switch connecting rod is blocked. For the former, the angle of the temperature sensor can be bent to make the action of pushing the switch connecting rod normal.

For the latter, it is necessary to find the obstructed part or foreign body, which can generally be restored to normal by removing the foreign body and correcting the position. 5.If the power switch is normal, the fault mostly occurs in the insulation switch.

First of all, see whether the reed of the bimetal sheet is pressed against the switch contact rod, if it is pressed too tightly, you can use tweezers to bend it upwards until the distance between the two. If the distance between the bimetal sheet and the switch lever is normal, the switch box should be disassembled, and the contacts and reeds of the insulation switch should be cleaned and repaired.

6.Common electric heating pipe damage, remove the electric reverence type heat pipe to measure its resistance can be judged. The electric heating tube is damaged and can only be replaced.

7.The poor contact of the electric heating pipe is mainly due to the serious corrosion of the contact reed in the power plug assembly or the shape of the change grip, which can be disassembled and repaired by the switch box, and it is best to replace it if the damage is serious.

Hello! That's it.

Hello! The above are the reasons and solutions for the electric kettle light to not light up and still heat.