How to disassemble and clean a dual power wave wheel washing machine?

1) Check whether the screws on the inner cylinder of the washing machine are clubs, slotted screws or Phillips screws. Select the appropriate screwdriver, remove the screw in the center of the wave wheel, and take out the wave wheel.

2) After taking out the wave wheel, use a screwdriver to remove the four screws around the washing machine workbench. Then bring the entire workbench up. There are generally four screws on top of the inner cylinder, and the screws of the contents are removed.

3) Use a wrench to unscrew the nut on the central shaft, and if you don't know what size screw it is, you can use a live wrench to unscrew the nut. You can take out the dehydration bucket.

4) Put the washing machine down, there is a protective ring at the place of the clutch, remove the sleeve and then unscrew the screws around the clutch. The washing machine was disassembled.

5) Clean the inner cylinder wall and clutch of the washing machine with cleaning agent, and then install it back as it is.

In short: the inner cylinder of the washing machine is also very dirty, the dirty things on the clothes are adsorbed on its surface, the same way, the inner cylinder cleaning does not need to be removed in a big way, we soak the towel with white vinegar, and then throw the towel into the inner cylinder of the washing machine, turn on the dehydration mode, let the vinegar volatilize into the washing machine, the towel can also adsorb stains, and then dissolve the alkali in the water, pour the solution into the washing machine, turn on the cleaning mode of the environmental protection cylinder, turn for about an hour, and then discharge the dirty water, which can play a role in sterilization and decontamination.

Disassemble first and then clean, the specific operation is as follows:

1. Use a Phillips knife to remove the screws on the washing machine.

2. After taking down the control panel of the washing machine, remove the screws inside with a Phillips knife.

3. Remove the overall plastic cover and clean the stolen goods.

4. Remove the sealing circular plastic retaining ring on the drum.

5. Use a long brush to clean the wall of the roller, and slowly brush out the dirt.

6. Use the 10 sleeve T-bar to remove the disc fastening screws at the bottom of the drum, take out the disc, add the washing machine cleaning solution to it, add two-thirds of the water, and clean it.

Prepare the tool:

Screwdriver specific steps:

1. Find a suitable Phillips screwdriver, and then unscrew the screws on the middle base.

2. When the screws are fully loosened, unscrew them by hand, so that the base is loose and taken out.

3. When taking out the base, it is best to tilt it and take it out at the place with the largest diameter in the washing machine barrel, otherwise it will be stuck and cannot be taken out.

4. After taking out the base, you can see that there are a lot of dirty things in the inner cylinder, and wipe it clean with a damp rag.

5. The taken out base can be directly rinsed with running water, pay attention to the front and back sides.

Cleaning and maintenance of washing machines:

In order to make the washing machine run normally and easily for a long time, it is necessary to carry out correct lubrication and maintenance on time, the main places that need to be lubricated are bearings and gears, and the bearings need to be injected with L-TSA22 anti-rust and anti-oxidation lubricating oil with good wear resistance and oxidation stability through the oil injection hole, and generally refueled once a year if used for general mechanical oil.

The gears should be lubricated with No. 2 extreme pressure lithium grease with good adhesion, or zinc dialkyl dithiophosphate with good oiliness with 1% mass content, or MOS2, L-CKC100 medium extreme pressure anti-wear gear oil with 3% mass content for lubrication.

The bearings and gears of the spin dryer should be added with L-AN15 and L-AN68 lubricating oil with good oxidation, anti-rust and anti-wear properties every year or half a year. If a sealed rolling bearing is used, it should be sealed by the bearing factory with a service life of more than 1000 hours, polyurea-based thickened refined petroleum lubricating oil, and No. 2 grease with anti-rust and antioxidant added.

Answer: The washing machine does not need to be disassembled for cleaning. You can use a small packet of washing detergent for washing machines, put it in the laundry bucket, start washing like washing clothes, and wait until the water is about to be released, then stop and cut off the power.

After soaking for four hours, turn on the power as you normally wash, press the Start Pause button, and the washing machine will work until the work is completed.

1. Disassembly of the frame.

1) Remove the fixing screws of the workbench and the box, and put the workbench vise on the box.

2) Unloading'Three fixing screws on the lower workbench and control panel to loosen the workbench and control panel.

2. Disassembly of the computer board.

1) Lift the outer edge of the control panel upwards with your hand so that it is detached from the frame.

2) Unscrew the screws, take out the waterproof plate first, remove the circuit board, and unplug the wire from the computer board.

3) Loosen the water level switch, install the fastening screws of the switch and the power switch, and remove the switches one by one.

3. Disassembly of the wave wheel.

1) Use the cross to loosen the wave wheel screw, unscrew out 10cm and then lift the screw by hand, and the wave wheel can be lifted. If you can't lift it, you can gently pry it up from a few positions on the edge of the wave theory with a flat mouth, and then lift the screw head.

2) When disassembling the wave wheel, if it is really impossible to remove it, you can first disassemble the V-belt and clutch pulley, and then take the wave wheel and hold the spring. For general clutches, as long as the clutch sleeve is removed, the inner shaft of the clutch can be easily opened, and then the wave wheel can be lifted together with the washing shaft.

Just buy a special cleaner for washing machines and operate it according to the instructions to save the trouble of disassembling and installing. If you want to disassemble, it is recommended to find a special cleaning company to disassemble and clean, which can save unnecessary trouble.

How to clean a washing machine, teach you the detailed steps to clean the washing machine correctly! Check it out!

2. Remove the filters on both sides, deduct the dirty things inside, and pour half a bucket of hot water.

3.Take 2-3 spoons of lazy artifact (depending on the size of the washing machine) dissolve in hot water and pour it into the washing machine with hot water, turn it for a while, and soak it for 4-5 hours (you can soak it for a while).

4.After soaking, remove large stains and wipe the walls of the cylinder with the sewage out.

Hello dear, the steps for disassembling and cleaning the dual-power wave wheel washing machine are as follows: 1. Remove the rubber pads on both sides. 2. Remove the screws of the protective cover of the computer board.

3. Fixing screws for the lower upper cover. 4. Use an electric base screwdriver to remove the four screws around. 5. Lift the upper cover plate and put it aside against the wall.

Of course, when cleaning the inside, the inner cylinder should also be cleaned, the inner cylinder can be disassembled, the dirt storage box on both sides is removed, the small cover plate of the fixing screws is fixed, the fixed screws of the wave wheel are removed from the cross, and the fixed screws of the wave wheel are removed from the cross, and the tools are slowly knocked loose counterclockwise, and the large nut is taken out, and the inner cylinder is taken out for cleaning. Of course, the installation after disassembly should be carried out through the opposite steps above, and it is recommended that if you are not familiar with the machine, do not try it easily, because there are often cases of assembly failure after disassembly. You can ask a professional to clean it once every six months.

Finally, I wish you a happy life.

The steps to disassemble the fully automatic washing machine are as follows:

1. Tools: a medium and large Phillips screwdriver, a small adjustable wrench, a stool or support lower than the washing machine.

Cut off the power! The washing machine was dismantled in situ, as power and drainage were also needed later. Use a screwdriver to loosen the screw counterclockwise, remove it, and lift the raised blade up with both hands. If there is water that is slippery, it is easy to dry it and lift it again.

2. This is the case with the back of the removed blade.

3. After the blade is removed, there are 4 screws here, which can be unscrewed with a screwdriver, most of them need a wrench to unscrew, if there is a hexagon wrench of the same size, it is simpler.

4. There is one such screw on the left and right sides of the outside of the washing machine, pry the shell open, and unscrew the screws. There are 2 more in the back, which are also unscrewed.

5. After unscrewing the 4 screws on the outside of the upper cover, you can lift the upper cover, be very careful at this time! The upper cover cannot be removed completely, it can only be flipped back, so one such support is needed at the back!

6. The upper cover cannot be completely removed because there are water pipes and wires connected, and do not mess with these wires, just keep it in this state. At this time, you will find that there is a lid on the barrel, unscrew 4 screws, lift 4 small buckles, and easily remove it.

7. At this time, shake the inner barrel, and put the inner barrel out, usually see the inner wall of the inner barrel, I think it is very clean, but in fact, the outer wall is very dirty, and the bottom!

8. After the inner barrel is removed, you will see this dirtiest outer barrel! Don't take off the outer barrel, because there is a drain pipe and a power cord underneath, which is more complicated, just disassemble and wash it, don't move it! Pour water into a bucket and brush with a brush or toothbrush.

9. That's it after washing!