How to deal with the water mist on the Tissot watch crystal?

Generally, if there is a water mist on a Tissot watch like this, it means that the watch has been flooded, and it must be repaired and sealed by a special repair shop, otherwise it will eventually conduct electricity and finally stop moving.

1. If an ordinary mechanical watch is damp, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it at about 15 cm near a 40-watt light bulb, bake for about 30 minutes, and the water vapor in the watch can be dissipated. Do not bake the watch close to the fire, so as not to deform the watch by heat.

2. Put the surface face inward, the bottom shell facing outward, and wear it on the wrist, and the water vapor can be eliminated after two hours. If the water ingress is severe, it is best to immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

3. Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch. The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

If you can't handle it yourself, you can send it to a professional maintenance center located at: [Room 05, 24th Floor, SAC Sichuan Aviation Plaza, Renmin East Road, Jinjiang District, Tel: 4000562678].

Well, good friend, your watch basically has this water mist to indicate that it is water, you take it apart and wipe it, and dry it with a hair dryer.

In terms of water, are you taking him with him a humid environment? You try to go to those places as little as possible.

There is fog in the watch, which means that there is moisture in the watch. In general, although the watch is hermetically sealed, there are very small pores in the joints of the case, especially in used watches.

When washing hands or washing clothes or on rainy days, water can enter through these pores, especially the hot steam in the kitchen, which is more likely to soak into the case. In addition, the temperature is high and the humidity is high in summer, so if the watch is suddenly cold, the air containing more moisture in the watch will condense into mist or water droplets, which will stick to the watch glass.

If water enters the watch, please send it to the repair center immediately for treatment, otherwise it will cause many metal parts inside the movement to oxidize and rust due to water vapor, causing greater damage. You can click on my homepage to consult, I hope to help you.

【Watch maintenance and repair can refer to the service center to go to 702, Xidan Joy City Office Building, Xicheng District, Beijing] to provide Tissot watch strap customization, cleaning and maintenance, identification, refurbishment, fault repair, watch appearance and replacement of damaged parts, and strap replacement services. Our technicians have undergone strict professional skills training and provide two years of after-sales guarantee services. The service center is guided by the watch manufacturer on the spot**, **transparent, no hidden consumption, no additional charges.

We can use the heating method to evaporate the water vapor inside, first pull out the crown of the watch completely, and then heat the watch with an incandescent lamp, so that the watch is heated to about 520 degrees, the temperature needs to feel yourself, can not be heated too high, otherwise it will affect the inner part of the watch movement, resulting in the second damage to the watch, we use the silicone watch together, put the silicone and the watch in a closed container, the silicone has a strong water absorption performance, you can remove the watch for a long time, observe the fog problem.

1. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is serious, it is best to immediately send it to the watch store to remove the imitation water in the watch, because if there is too much water in the mechanical watch, there is no way to dry it in time by adsorbing it from the outside or drying it.

Brother 2, the watch belongs to precision machinery, whether the watch water has an impact on the watch accessories, this is not sure, this has to look at the dust fiber to see if the watch water is very serious, and how the waterproof of the watch is. If it is only the watch of the watch that is fogged, it is estimated that the water ingress of the watch is not serious. If it causes the watch to slow down, not to go or other problems, it is estimated that it will have an impact on the watch accessories.

Therefore, it is recommended to go to a professional watch repair center for testing, and the general inspection is free.

The solution is as follows:

1. If there is only a small amount of mist, it will disappear by itself after a period of time, or it will be baked under a light bulb;

2. Put the surface facing inward, the bottom shell facing outward, and wear it on the wrist, and the water vapor can be eliminated after two small bends;

3. If there is a lot of water, you should find a professional for maintenance;

Although the waterproof watch has been treated with a certain amount of waterproofing, it is generally not strictly inspected, and it is avoided to touch the water when wearing it to prevent damage.

1. If the watch is soaked in water, you can wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, put it at about 15 cm near a 40-watt light bulb, and bake it for about 30 minutes, and the water vapor in the watch can be eliminated.

2. Put it in a rice jar and bury it deep in the dried rice for a period of time, if it is fast, you can see obvious results in one night.

3. You can use a granular substance called silica gel to put it into a closed container with the watch that has accumulated water, and after a few hours, take out the watch, and the water will disappear.

4. Take a hair dryer to dry, and then apply a layer of transparent nail polish on it to avoid impurities and prevent rust.

5. If there is water vapor in the watch, you can wear the watch face inward and the bottom shell outward, and wear it on the wrist to eliminate the water vapor in two hours. If there is too much water in the watch, the case must be opened and scrubbed. If you are not sure to deal with it yourself, you should send it for repair in time.

There are several ways to remove water mist from the inside of the dial: using silicone, using a light bulb, sunbathing, rice, and a hair dryer. Place the watch and silicone in an airtight container filled with silicone and let stand for about 5 hours.

Wrap your watch in a cotton cloth, bring a light bulb and bake it in front of a 40 watt light bulb for about 30 minutes. Open the back cover of the watch, wrap it in a paper towel and expose it to the sun. When wearing the watch, wear the glass inwards and the bottom case outward, and put it on the wrist.

After waiting for a while, it can also have an evaporating effect. Wrap the watch in a towel first, then pull out the crown of the watch and place it near an incandescent lamp to heat the watch, which can evaporate the water vapor and remove the water mist on the mirror of the watch. Never bake the glass directly over the fire.

Pull out the crown and find a container that can be sealed and prepare a packet of food desiccant. Put the watch and desiccant in a container and let the desiccant absorb the moisture in the watch.