What should I do if I find that the billiard table is uneven during installation?

Look at the appearance: a good table is beautiful, fine workmanship, elegant paint, and bright color balls, velvety green tweed matching, like a precious handicraft, a look will produce a strong desire to play. The inferior table is rough in workmanship and dull in paint, which visually gives people a very incongruous feeling.

Look at the workmanship: the workmanship of the high-end table is fine, horizontal and vertical, and the joints are tightly sealed; The paint is smooth as a mirror and feels smooth and delicate. Also, if you hit the edge of the library with a little hard with your waist, will the ball on the table shake?

The less shaking, the better. The platform that cannot be knocked shows that the wood used is hard, well-made, and has a compact structure. Look at the library side:

Look at the part where the edge of the library is in contact with the table surface without a gap (i.e., the straightness on the vertical surface). When the edge of the library is deformed, it is generally the middle drum or both sides are upturned. If the gap is small and you can't see clearly, you can try to insert the bank card you carry with you to the bottom of the library, and it is better to insert it if you can't plug it in.

Squat at one end of the library edge to see whether the two library edges and the rubber edge are in a straight line on the horizontal plane (i.e., horizontal observation); See whether the edge of the library is parallel to the countertop, and see whether the edge of the library and the edge of the glue are upturned or downturned. Look at the mouth of the bag: take the slate round under the mouth of the bag as the center, and see whether the arc of the library edge on both sides is symmetrical, whether the edge curve of a single arc is smooth and consistent.

Look at the tweed bag at the mouth of the bag to see if there are pleats, especially the middle bag. Look at whether the cowhide at the mouth of the bag is flat, and whether the gap between the edge and the edge of the library is too large. Shake the mouth of the bag up and down with your hands to see if it is loose.

Hit the cue ball vigorously with the middle stick to see if the target ball spits out when it is hollow into the pocket. Watch the ball: Let the ball roll on the table to see how fast or slow it is, whether it is even, whether it changes the line, and whether it shakes from side to side when it is time to stop.

A good table ball is fast, as smooth as flowing water.

When the billiard table is installed, it is found that the unevenness is uneven, the first thing to check is how big the uneven distance is, if it is not serious, it can be leveled through the pad fireproof board, if it is more serious, the customer's address is far away from the company, and the office can find a carpenter to carry out on-site planing. When the billiard table is installed, it is found that the height of the table legs is different, find out the highest leg, use it as a standard, level the large shelf, and put a leg spacer under the short leg. When the billiard table is installed, it is found that the steel gang and the wooden gang are uneven, the first thing to check is whether it is the deformation of the wooden gang, if the deformation of the wooden gang is not serious, use external force to flatten the protruding part of the wooden gang when fastening the wooden gang and the steel warehouse screws, and then tighten the screws.

When the billiard table is installed, it is found that the hole position of the steel warehouse and the wooden gang is not the right or the hole position of the slate support is incorrect, and the hole position of the steel warehouse or slate is used as the specification, and the hole position of the wooden gang or slate support is fine-tuned, and the hole is drilled from scratch if necessary.

It can be adjusted horizontally and vertically, and the ground should be leveled. The line change of the ball is not completely caused by the unevenness of the table, but the line change in a small range, such as when hitting the sticker ball, when the ball is close to the mouth of the bag, is mainly due to the long use of the table nickname, resulting in the inconsistent thickness of the table nick fluff. Under normal circumstances, when the table is initially installed, it will go through the leveling procedure, even if it is used in the process, the uneven situation is relatively slight, in this case, measure the table with a level, fine-tune it at the table foot, if the situation is more serious, it is best to find a professional person to level, and the manual cost is about 100 fast.

Don't listen to those who don't know how to talk nonsense, as long as it is an assembled billiard table, it is best to have a professional technical person to level it, you may not know the structure of the assembled billiard table, which is three stone slabs with a thickness of four centimeters, if you can't install, it is difficult to install flat, if you can't install, it's best to find a billiard table business that can be installed for free. I suggest you take a look at the gentleman's billiard table, the gentleman's billiard table is installed by customers for free, and the after-sales service is good.

Only Qiao's billiard table has professional technicians who use that kind of equipment to level in order to achieve "flatness". I haven't heard of any other brands yet.

There is no technical content, practice makes perfect, and it will be paved a few more times. Much easier than playing billiards.

1. Factors affecting the levelness of the billiard table:

1. Adjust the level by yourself and change the initial state.

2. Move the billiard table by yourself.

Suggestion: Please find a professional to install and debug.

2. Factors affecting the levelness of the slate.

1. Stepping on and sitting on the slate causes the deformation of the slate.

2. Playing the jump ball, the slate is hit with a small pit, and the ball path changes line.

3. Disassemble and assemble the billiard table by yourself, so that the joints of the slate are uneven, which changes the direction of travel of the ball in motion.

Third, the factors affecting the library edge.

1. Hard objects hit the edge of the warehouse violently.

2. The rubber strip will age and harden when exposed to high temperature or for a long time.

3. The table is damaged, changing the angle of the ball.

4. Sit and press down the small helper, resulting in the change of the parallelism between the library edge and the table.

Fourth, the ball bag.

1. When the blast is hit, the first force directly acts on the chamfer of the slate at the mouth of the bag, and there is a knife-like crack on the table.

2. When the ball is hit, the leather of the bag mouth is damaged, and the ball is damaged when it hits the copper mouth directly.

3. Excessive use of the explosive rod, its impact force hits the front end of the slideway, and the nut loosens and the ball is left and leaked.

4. Check the ball bag and slide nut regularly.

Fifth, what about Taiwan. 1. Do not pour any liquid into the countertop to shorten the service life of the countertop.

2. Replace the table regularly and clean the countertop.

3. Use a standard club to prevent the club head from tearing the table.

Original! I don't know what injustice you're referring to.

1. The level is not leveled.

Let the master who installed the table adjust.

2. The slate has been used for a long time, and there are pits due to the ball hitting on it.

Find the manufacturer of the table to see if you can turn over the slate and use it, or what to use to fill the pit, if it doesn't work, you can only replace the slate.

3. The platform is uneven.

Iron along the hair with a specially ironed countertop. If the table is used for too long, replace it. The color near the middle pocket of the new tweed is lighter than that of other places, and the speed of the ball will also be very fast.

Hope mine can help you.

Either change the tablecloth or iron it.

Use a spirit level to see the level, and use something to pad the bottom of the table in uneven places.