The master enters the !! tenda w311R wireless router

If you're sure you haven't changed your router's IP (here's what you can do:

1. Modify the IP of your computer and a network segment of the router (e.g., x cannot be 1 and 255,);

2. Connect the LAN port of the computer network card and the wireless router with a network cable;

3. Enter the IP address of the router to log in.

If you are not sure whether you have changed the IP or not, and you can't remember the IP of the router, then you can find a toothpick and press the reset button of the router for a few seconds to reset the router, find the default IP of the router (usually or the user name and password (in the body label or manual) or follow the above steps.

The router is shut down and restarted, and the network cable connected to the computer is unplugged and plugged back in.

The easiest thing is to turn your computer and your router off and then turn it on.,I don't believe you can't get in.,To two in a segment.。

Check to see if your computer and router's addresses are on the same network segment.

The troubleshooting scenarios in the WAN status display connection are as follows:

Q1: In the advanced settings of the router's management interface - "System Status", the connection status of the WAN port shows that it is connected, and it cannot be connected to the network, what is the problem?

A1: The following troubleshooting steps are as follows:

1. Check whether the connection method is correct, if not, please select your correct Internet access method to set it.

2. What is the problem that the connection mode is correct and the connection mode is pppoe, but the connection status still shows that the connection is in the connection?

2. The broadband user name and password are entered incorrectly.

3. Network cable problems.

Solution: In the management interface of the router, you need to click "Advanced Settings" - "Mac Clone", then click to clone the MAC address, then click OK, and then restart the router with the system tool, and then check the system status.

2. After cloning, the WAN is still displayed in the connection, "Advanced Settings" - "System Tools" - "System Logs" to view the log content, the log records the entire process of router dialing, and view the system log on the last 3 pages

A: If the following log content appears:

If the following logs appear:

You can change the WAN port rate of the router (click "Advanced Settings" - "WAN Port Rate Control" or "Advanced Settings" - "WAN Parameter Settings") to 10M full-duplex, and then "Advanced Settings" - "System Tools" - "Restart the Router". Or replace the network cable connected to the WAN port of the router.

You can also refer to the following **: WAN port to display the troubleshooting method in the connection.

Connect the network cable of the router to the WAN port.

How to set up your Tenda W311R wireless router Step 1: Open your computer's browser and enter.

Step 2: Go to the router settings page, select ADSL dial-up, and enter the broadband account and password provided by the operator. The wireless password is the wireless password for setting the router.

Step 3: After entering the bottom of the post-entry point, confirm the setting to complete. Then you can surf the internet.

First of all, there is one thing that needs to be declared and determined.

The setting of the wireless route, has nothing to do with the operating system, the wireless router itself has background settings, no matter what system it is, enter the gateway in the browser (or can enter the routing setting platform.

You cancel the password of the wireless router, that is, do not turn on the wireless security, and then cause you to be unable to access the Internet, I think, it should be the routing settings changed, please log in to the route again, confirm whether the PPPOE connection of the WAN has a set account password, and whether it is in the connection state.

The router needs to be set up according to the Internet environment, select the correct Internet access method, and then you can access the Internet normally, and the specific setting method of the router is as follows:

Connect the network cable and power supply.

Then go to the router settings page.

Enter the account password and set it step by step.

The instructions are very detailed. Be careful when filling in your account number and password.