Konka LED32F3700PF how to use the Internet to watch TV and how to operate? Thank you.

Dear users:

Hello, sorry for the inconvenience caused by the product! Due to the recent clean network action carried out by the State Administration of Radio, Film and Television, the software and resources of smart TV are reviewed, resulting in the unusability of the best software in most domestic brands of smart TVs, and the specific time schedule is controlled by each licensee; We apologize for the inconvenience! During the review, it is recommended that you connect your TV to a set-top box, a wired signal, or use your TV as a monitor to connect it to your computer.

1. Preliminary preparation.

1.Make sure your TV is connected to the Internet.

2.You need to insert the USB flash drive and keep the USB flash drive connected all the time.

3.During use, keep the USB flash drive connected, otherwise it will affect the normal **.

1.Open the TV menu, select the "App Store" option under Smart TV, 2Find "Huashu TV" in the recommendation bar or life bar of the app store

5.Find "Wasu TV" in all apps

6.Once the load is complete, it will work normally**.

This problem has been shared by netizens in the znds forum with detailed solutions, you just need to go there to find it and follow the tutorial to solve it.

1) Press the "Vegetable Collapse Sail Single" button on the remote control of the set-top box to find the "Settings" option;

2) In the settings menu, find [WLAN] and click to enter;

3) Click the [Turn off] button in the upper right corner of the [Wi-Fi settings] page, and click to turn on [Wi-Fi].

4) Click to open, a lot of wireless network names will appear on the [WLAN Settings] setting page, find your wireless network and click to enter;

5) Enter the password of the wireless router, the general wireless password is 8 digits, if you don't know, according to the ** provided behind the wireless router, log in to set up, you can turn on the wireless network, so that the set-top box is connected to the wireless network.

If you need a wireless network connection to your TV, you need to connect an external wireless network card and connect to the wireless signal sent by the wireless router at home.

1. Wireless connection needs to match: wireless network card (it is recommended to use RTL8191SU, RTL3070, RTL8712 as the main chip of the wireless network card, drive-free, plug and play; If the TV has a built-in wifi function, it is no longer necessary to configure a wireless network card), a wireless router, a computer, and an IP TV.

2. After the wireless router and the computer can be connected to the network normally, please connect the wireless network card to the TV;

3. The router adopts WPA encryption mode, and the settings are as follows: the password type is TKIP, the PSK EAP is PSK, and the password needs to be set to 8 digits. (It is recommended to use pure numbers for passwords to be easy to identify).

4. TV: Settings - Network - Wireless Settings - SSID (search for router devices), encryption type (the same as set on the computer), IP type Select the automatic key check, and finally click Settings.

5. If it is a built-in wifi function, settings-network-wireless settings, turn on wifi, select the name of your router, there will be a dialog box to pop up the manuscript socks, prompting you to fill in the password, please use the Konka remote control keyboard and mouse to enter the input. After entering, click on the connection first, and then click on the network detection. If the TV prompts that the network has been restored and the network is connected, it means that the TV has been successfully connected to the Internet!

According to your feedback, Konka IPTV wireless networking operation is as follows:

Wireless connection: 1. Wireless connection needs to be matched: wireless network card (wireless network card needs to be purchased and matched by the user, if the built-in wifi does not need a wireless network card), wireless router, computer, network TV.

2. After the wireless router and the computer can be connected to the network normally, please connect the wireless network card to the TV (no driver, can be installed and used directly).

3. TV menu-Network Settings-Wireless Settings-SSID(Search for router devices)、Encryption type(Same as set on the computer)、IP typeSelect automatic getting,Finally, click Settings。

In addition,The wireless router settings that our TV can recognize are:Adopt WEP encryption method,The settings are as follows:The authentication method is selected as Open, WEP encryption is selected64bit, the key mode is selected ascii, any key can be set, and the password needs to be set 5 digits。

Alternatively, use WPA encryption and set the following parameters: set the password type to TKIP, select PSK EAP to PSK, and set the password to 8 digits. Passwords are recommended to be purely numeric.

Konka enterprise knows that to provide you with high-quality solutions, attentive to answer your questions, hope to be able to get you.

Dear users: Hello, thank you for your support to Konka! Konka LED48F3700NF has a chain embedded HDMI input interface, which can be connected to the computer through the version of the HDMI cable, and the TV can be used as a computer monitor, but some settings need to be noted, 1. The resolution of the computer should be within the range of the TV (such as 1024*768, etc.);

2. The refresh rate of the computer should be 60Hz;

Both of the above points require the user to right-click on the advanced settings in the "Properties" on the desktop of the laptop or desktop computer).

3. Turn on the TV first, put the TV on HDMI (according to the dialog box that pops up in the remote control menu of the TV, the computer signal source displayed by different TVs is different, such as the option "Computer Studio Balance" in the TV menu, select the computer) under the status of the liquid simplification, and then start the computer host to let the TV automatically identify the signal of the computer. (Note: Do not turn on the computer first and then turn on the TV, that may not have a picture); Thank you for your attention to Konka products and wish you a happy life!

Wireless connection: A wireless router is required. The router segment must be set as follows:

WPA encryption mode is used, and the settings are as follows: TKIP is selected as password type, PSK ESK is selected as PSK, and 8-digit password must be set to SWe. (Note:.)

The password is recommended to use the number 0-9 TV is easy to identify),After setting,Select the wireless network of the electric search and combustion vertical viewing machine,Automatically obtain the IP address,The connection is successful,Thank you。 Thank you for your consultation and have a great day!

Dear users:

Here's how to do it with a wireless connection:

1. Wireless connection needs to be matched: wireless network card (wireless network card needs to be purchased and matched by the user, if built-in wifi, no wireless network card is required), wireless router, computer, network TV.

2. Set the encryption parameters of the router. It is recommended that you use the WEP encryption method, and set the following settings: open for authentication mode, 64bit for wep encryption, ASCII for key mode, any one key for one, and 5 digits for password.

Alternatively, use WPA encryption and set the following parameters: set the password type to TKIP, select PSK EAP to PSK, and set the password to 8 digits. Passwords are recommended to be purely numeric.

3、Turn on the TV and enter Settings-Network-Wireless Settings-SSID Select the name of your router,There will be a dialog box popping up,Prompt you to fill in the password,Click Settings first after entering,Then click Network Detection。 If the TV prompts that the network has been restored The network is connected, indicating that the TV has been successfully connected to the network.

Here are the steps to do it for wired networking:

1. Wired connections need to match: routers, network cables, computers, and network TVs.

2. First of all, the router and the computer can be connected to the network normally (when wired connection, please set the IP of the computer to automatically obtain; Connect the computer and the router, log in the router, generally on the back of the router, such as: etc., after entering the **information,), connect a network cable to the router at one end, and connect the network interface of the TV at the other end.

3、The TV is cut off and the power is restarted,Enter the TV system settings-network-cable-IP type automatic acquisition-setting-network detection。