How to tune the Nikon D7200 to AF

Photography for beginners: From an APS-C perspective – the DX lens (PIAN) head (YI) shall prevail.

Even though the Nikon D7200 is a high-end flagship SLR camera, it is still an APS-C camera, so the lens is matched with a high-quality and inexpensive DX format lens, which is suitable for home users who are new to photography, and there is no intention of upgrading to full frame.

Set lens 16-85mm or 18-140mm

The set lens is indispensable for this kind of user, and the focal length of the lens is a common focal length and is used in a wide range. Among them, Nikon AF-S DX 16-85mm IF-ED VR is a DX format, excellent performance of daily use, VR performance is very good, to a certain extent, it can be said to have the quality of Nikon gold circle lenses, imaging belongs to Nikon set of lenses is very good. The equivalent focal length is that it is possible to shoot large scenes** at the wide-angle end, and at the telephoto end, it can shoot distant scenes.

The Nikon AF-S DX 18-140 G ED VR is cheaper than 16-85mm, the main difference is that the imaging is slightly worse, but the shooting distance will be longer, and the equivalent focal length at the telephoto end is 210mm, which can be used as a sleeve for the world to a certain extent.

Nikon AF-S DX Nikkor 10-24mm F ED

This lens is the widest lens in Nikon's APS-C, and it is the most suitable wide-angle zoom lens for the Nikon D7200 if you are not planning to upgrade the full-frame camera with a full-frame 12-24mm focal length and a focal length range of 10-24mm (equivalent to 15-36mm in the 35mm format).

AF focus adjustment method,If the shortcut key is not very good,You can operate it directly in the program,There are single-shot、Continuous,Servo and the like in the focus options。

The Nikon D7100's focusing AF-S mode cannot be switched to AF-C and AF-A, which is caused by the wrong setting of the smart bend, and the solution is as follows:

1. Turn on the DSLR camera.

Check out that the current focus mode is one-shot focus.

2. Find the AF M button on the body of the SLR camera.

3. Press and hold the previous step to find the AF M on the fuselage, and a similar interface will appear on the screen.

4. At this time, dial the wheel on the motor body to change the focusing mode, pay attention not to release the AF M button at this time, you need to press and hold it.

5. Toggle the dial wheel until the pre-focus mode is AF-C, and it is AF-C when you return to the main interface.

Here are some tips for setting parameters for this camera:

1.ISO Settings: The D7200 has a wide ISO range and can be used in all types of light conditions.

However, high ISO will produce noise in **, which will affect image quality. It is recommended to choose the appropriate ISO range according to the light conditions to ensure the quality of **.

2.White Balance Settings: In different light conditions, white balance settings are critical to the color performance of **. The D7200 offers a variety of white balance modes, which can be adjusted manually or automatically. Blue limbs.

3.Focal length settings: The D7200 has 39 focus points, which can be selected manually or automatically.

If you want the subject to be highlighted, you should select the appropriate focus point, place it on the subject, and use AF-C (continuous autofocus) or AF-S (single autofocus) mode to ensure sharp**.

4.**Settings: The D7200 provides a variety of exposure band light modes, including Auto**, Aperture Priority, Shutter Priority, Manual**, etc., users can choose the appropriate **mode for shooting according to their needs.

When shooting different scenes, you can use the amount of compensation adjustment to ensure that the correct level of brightness and darkness is rendered.

5.Shutter settings: The shutter speed will also need to be changed accordingly under different shooting conditions. It is recommended to use a slower shutter speed to capture static or slow-moving subjects, and a faster shutter speed to capture fast-moving subjects to avoid motion blur.

Here's how to set it up:

1. In the lower right corner of the D7200 camera, there is a switch between M and AF. Press and hold this button and use the front wheel to switch between 3D, Auto, Single Point, 9 to 51 Point Dynamic, and several focus modes.

2. According to the lens auto such as silver focus area needs the root focus mode button, after striking the vibrator, the shoulder screen will display a single point or auto, if in AF C mode, it will add 9 points, 21 points, 39 points, 51 points, 3D and all auto.

If you like that kind of on-screen focus.

To indicate the effect of the point, follow the steps below. The focus servo mode lever on the body is selected to S (single auto), and the lever has three gears: M, S, and C. The focus mode of the fuselage is selected as 51-zone auto (auto), and when you press the shutter at these two and a half points, there will be a lot of focus points, and the lit focus points indicate that these points are in one focal plane.

I have used Nikon SLR for eight years, one of which is D7000, you need to consult the manual for specific operation, I can't remember the specific names of these lever buttons and settings, but this operation is absolutely correct.

Look at whether the AF selector switch on the lower left side of the fuselage is in the AF position, and then press and hold the middle is button to adjust the AF mode using the main command dial.

InLV modeBottom (i.e., framing with the screen), there are only two modes: AF-S and AF-F;

in useViewfinder, you can switch between AF-A, AF-S, and AF-C modes (remember to keep your eyes in the viewfinder to see).

In both framing cases, the mode shown is different, and yesThere is no hairy relationship between the two, It's not clear in the manual, I don't know what this designer thinks in his head.

The D7000 I use, the 7100 should be the same, press and hold the small round button on the AF, and then toggle the sub-command dial to change the mode.

Whether it is a single or continuous focus, the focus is preferred, and the camera will be focused first, which means that the focus is good first and then the image, and if the release is prioritized, there may be images regardless of whether the focus is aligned or not.

The latest Expeed2 image processor at the time, along with a new 2016-pixel metering sensor, a 3-inch LCD display, and Nikon's latest 39-point autofocus system.

The default settings for Nikon DSLRs are focus priority for AF-S and release priority for AF-C, which can be modified in the custom menu A1 and A2. When taking a group photo, the subject is basically stationary, and the camera can be used in either AF-S or AF-C focus mode.

Hello! Your question is not clearly described, and I don't know what you are asking. AF-C and AF-S refer to the camera's focus mode, AF-C is continuous servo autofocus and AF-S is single-shot servo autofocus.

When shooting moving subjects in AF-C mode, when the shutter is pressed halfway, the camera's focus point keeps tracking the moving object and keeps adjusting the focus point until it is completed**; When shooting still subjects, the AF-S mode is often used, and when the camera presses the shutter halfway to focus, the focus will stop as long as the focus is locked, and the focus will not change as long as you don't start focusing. If you take a group photo, you can choose AF-C mode.

Summary. Can a Nikon camera be converted to a Canon lens?

1. No, you can't. (Not absolutely, there will be infinity that cannot be focused) 2. The reason, which involves the term "flange focal length".

The Canon EF mount has a relatively short flange focal length, but the addition of a lens adapter will make the flange focal length of the EF mount longer (it should be said that a new, longer flange focal length will be formed), which can be matched with other lenses with longer flange focal lengths, so that the Canon EF mount can use lenses from all other brands of mounts (manual focus) without being out of focus at infinity.

Another reason why the Canon EF mount can be used with all other brands of mounts is that the Canon EF mount has the largest diameter among the many 135 mounts, and has a large image circle, which is convenient for adapting to other brands of mount lenses with smaller diameters.

Due to the flange focal length, Canon cameras can use Nikon lenses through adapter rings, and Nikon cameras cannot use Canon lenses through adapter rings.

How to transfer Nikon D800 to Canon 70-200

Can a Nikon camera be converted to a Canon lens? 1. No, you can't. (Not absolutely, there will be infinity that cannot be focused) 2. The reason, which involves the term "flange focal length".

The Canon EF mount has a relatively short flange focal length, but the addition of a lens adapter will make the flange focal length of the EF mount longer (it should be said that a new, longer flange focal length will be formed), which can be matched with other lenses with longer flange focal lengths, so that the Canon EF mount can use lenses from all other brands of mounts (manual focus) without being out of focus at infinity. Another reason why the Canon EF mount can be used with all other brands of mounts is that the Canon EF mount has the largest diameter among the many 135 mounts, and has a large image circle, which is convenient for adapting to other brands of mount lenses with smaller diameters. Due to the flange focal length, Canon cameras can use Nikon lenses through adapter rings, and Nikon cameras cannot use Canon lenses through adapter rings.

So if you can not transfer, you will not transfer.