Share a router with others, why the same router can be used by others

**Things are not the same, the speed may not be the same, first make sure that others are not using software to limit your network speed, if not, do not use the route to see how your network speed is, and then release the 20% bandwidth that is reserved in your computer, method: first you must log in to the system as a user with the identity of a system administrator, and then actually click Start Run, enter "Press OK, double-click "Local Computer Policy" under "Computer Configuration" "Administrative Template" "Network" in the running dialog box that appears. QoS Packet Scheduler", on the right side of the screen will appear the settings for the QoS Packet Scheduler item. Then click on "Limit Reservable Bandwidth" in the sub-project on the right.

Click "Properties" next to "Display" under "Limit Retained Bandwidth" (or select the sub-project "Limit Retained Bandwidth", or right-click "Properties"), the "Limit Retained Bandwidth" dialog box appears, click "Settings", select "Enabled", then set the % next to "Bandwidth Restriction" to 0%, and then press OK to exit. 2.Then select the connection you have established, right-click on the properties, click on the network in the connection properties that appear, and in the network dialog box that appears, check whether the "QoS packet scheduler" is checked in the "This connection uses the following items", and press OK to exit if there is no problem.

First. line factor. If the network cable is too long or the quality is not good, the network speed will be very slow.

Third. Speed limited. It's unlikely, though. You can try a different IP address or a different network card or a different computer. If you change it, it will be fast, and the speed will be limited.

The speed can be controlled with the polysheng network management.

What should I do if someone else can access the Internet on the same router but I can't? In fact, this problem is also easy for many friends to encounter, so I will briefly analyze the reasons for the possible problems:

First, IP conflicts

IP conflict, this situation generally occurs on the secondary route, what is the secondary route, in layman's terms, is in the case of the original router, and add a router, your computer's IP address and the main router's IP conflict, in this case, it is recommended that you enter the router to change your IP address to be different from the main route, but it must be in the same gateway, the general main route IP address is, you just need to change it to as long as it is not consistent with the main route!

Second, ARP conflicts

ARP conflict, ARP attack is the use of data packet transmission in the LAN to attack other users, non-stop sending of data packets resulting in a computer network data instability in the LAN, so that users often disconnect the network or can not access the Internet normally, for this we can use 360 and other software to intercept, the best way is to set a static mode, the IP address and MAC address binding.

Third, it is limited by the router

Maliciously restricted from surfing the Internet,The current routers have this function,You can restrict the Internet access and the current traffic of the signal bend,This is recommended that you go into the router to take a look,If the IP is restricted,Just recover from it!

Fourth, set the mode to guess the binding of the Mac

Set up static mode, and bind to the Mac, your computer IP and Mac are not in the settings, this is generally used by many companies, you can't access the Internet without the authorization of the administrator!

Gaoquan message above are the common reasons for not being able to access the Internet normally, it is recommended that you eliminate them one by one, but the premise is that you must confirm that the external network must be unblocked, the network cable and the router connection is correct, the crystal head these must not be wrong, if the above methods can not solve your problem, then you can try to reinstall the system, some may be caused by viruses, well, I will say so much about this, I don't know what other reasons my friends think are welcome to leave a message**, If you like it, don't play a little slippery, like it, follow a wave, thank you!

Modify the router's entry path, login, account and password, and modify the address pool assigned by the router.

1. If the path to enter the router is, after you enter the router, take a closer look, there is such an address, modify it to enter the path later).

2. Change the router password. (The default is damin), [restart the router here once, test your settings above].

3. There is an address pool in the router LAN. You have three computers in your house (i.e. only three.)

4: Your home computer is set to a fixed IP: and and.

Subnet mask. DNS: is preferred for the gateway

Complete the steps above and you're good to go!!

You're using a wireless router. It could be that someone else has stolen your signals. You changed your password.

3.Check the routing settings, unlimited routing, please check if the former rate is faster than the latter.

4.Virus causes ARP virus to be funny in the LAN, and the ARP LAN virus will disconnect or slow the connection.

over！Didn't understand hi me

Router dial-up or computer dial-up?

Is the account in the router?

Hello, you mean a wireless router and a router connection is possible.

1. How to set up the main router:

1. Plug the network cable (bus) into the WAN port of the wireless router, plug one end of the network cable into any LAN port of the wireless router and connect the computer network card at the other end, and turn on the power supply of the router.

3. Then enter admin, the default account name and password are the same (there is also a prompt for the original data on the back of the router) to confirm.

4. After entering the wireless router setting interface, select the Internet access method according to the setup wizard (different broadband options are also different), and enter the Internet access account and password.

5. Save and continue to set the wireless key, (it is recommended to use a combination of numbers and English for the password, and it is best to use the @ symbol in the middle, so as to prevent others from rubbing the net).

6. After saving, you can surf the Internet normally.

7. If it is abnormal, you may wish to click the reset button of the wireless router and set up the router again.

Second, the setting method of the secondary router:

1. Do not connect the secondary router to the main router first.

2. One end of the network cable is connected to any LAN port of the secondary router, and the other end is connected to the computer.

3. Change the LAN port IP of the login interface through the computer browser to avoid conflicts with the IP segment of the main router;

4. WAN port Internet access mode selection: dynamic IP connection, enable DHCP server.

5. Set the account and key wirelessly, save and log out.

6. Connect a network cable from any LAN port of the main router to the WAN port of the secondary wireless router, and the computer can access the Internet at this time.

In fact, there is one of the easiest ways, the switch does not need to connect to the computer to divide the long line into four to make a circuit, that is, to leave the 1236 four, 4578 four strips out, as another line of 1236 to make two crystal heads, the problem is that you must be able to do network cables. Or you buy a good network cable, cut it from the middle, set aside all eight lines, and pull the long line closer to the computer, don't cut it, and then find out the blue and white, blue, brown and white, brown and brown, cut it, and connect the switch against the router side and the yellow and white, yellow, green and white in the half you bought. In addition, the same should be done on the router's side, and the order should be the same.

With today's hardware, your requirements are not achievable.

Find another route, connect it to the front of the switch in the bedroom, remove the long wire (or not), and directly do wireless routing expansion.

There are many specific wireless routing WDS methods on the Internet.

According to your second diagram, it would be nice if you bought a connector. This will allow you to add the line.