Computer malfunction does not run What happens when a computer program does not run

The system is gone. Gotta reinstall.

1.Find the start in the lower left corner, the stand-alone "Run" column.

2.Enter %systemroot% system32 to copy and paste directly, and then press enter to enter the traditional command prompt (enter a space for easy copying).

3.Start by typing assocexe=exefile Enter the enter key.

4.Then enter ftype exefile="%1"%* Enter Enter.

5.The renderings are as follows.

What's going on with the computer won't boot.

Ctrl+Alt+Delete brings up the task manager to end the task, don't operate too often, and wait for a while in the background.

Hello landlord.

Open Control Panel - Management Tools - Services to see if all the service items in it are disabled.

It's really not possible to restart the computer point F8, select the safe mode, and see if you can operate If you can, you can't do antivirus, only the operating system.

The easiest way to do this is to reinstall the system.

It is recommended to enter safe mode for diagnostic startup.

1. Enter safe mode.

Click Advanced Options in the above figure, start the settings, press F4 to enter safe mode after restarting2, think about what software is installed, uninstall the driver in safe mode, uninstall third-party WiFi software that is easy to cause conflicts, antivirus software, etc. At the same time, open Device Manager to uninstall the graphics card drivers that are prone to conflicts. Then start normally and try it.

3. Press Win R to enter msconfig on the desktop in safe mode, open the system configuration, click Diagnostic Startup, and then restart the computer, which will automatically fix the problem. Fix the problem and start normally.

4. The problem is still to reset the operating system, reboot into advanced mode, and troubleshoot in advanced mode. Click Reset this computer and follow the prompts to reset the operating system.

Computer problems, you know, it will be better to smash it directly.

Something went wrong with the hardware, according to what you said about the computer"Two bs"Ring: If you are talking about the real situation, please unplug the power supply, remove the Bois battery for 10 seconds, plug it in and start it again, it is best to wipe the gold finger of the memory module, and then plug the other hardware again to clean up the dust of the case. If that doesn't work, unplug the keyboard and try again.

The following is an explanation of the BIOS alarm sound, judge it yourself according to the actual situation, because you didn't say the motherboard model, it's not easy to judge.

Now there are two kinds of BIOS commonly used in motherboards, "AMI and AWARD", and their definitions are slightly different due to different manufacturers.

Award BIOS Alarm Tone**:

1 Short: The system starts normally. Congratulations, there is nothing wrong with your machine.

2 Short: General error, please go to CMOS Setup and reset the incorrect options.

1 long and 1 short: There is an error with the RAM or motherboard. Try to change the memory, if it still doesn't work, you have to change the motherboard.

1 long and 2 short: The display or graphics card is wrong.

1 long and 3 short: The keyboard controller is wrong. Check the motherboard.

1 Long 9 Short: Motherboard Flash RAM or EPROM error, BIOS corruption. Try a different block of flash ram.

Constant ringing (long sound): The memory module is not plugged in tightly or is damaged. If it still doesn't work, you can only replace a memory module.

Repeated, short ring: There is a problem with the power supply.

No sound and no display: There may be a problem with the power supply.

Below is the alarm tone for the AMI BIOS**:

1 Short: The memory refresh failed. Replace the memory module.

2 Short: The memory ECC verification error is incorrect. Setting the memory option for ECC check to Disabled in CMOS Setup will solve the problem, but the most fundamental solution is to replace a memory.

3. Short: The basic memory of the system (the first 64KB) failed to be checked. Change memory.

4 Short: The system clock is wrong.

5 Short: Processor (CPU) error.

6 Short: Keyboard controller error.

7 short: The real mode of the system is wrong and cannot be switched to protection mode.

8 Short: A memory error is displayed. If there is a problem with the display memory, try changing the graphics card.

9 Short: ROM BIOS check and error.

1 long and 3 short: memory error. If the memory is damaged, it can be replaced.

1 long and 8 short: A test error is displayed. The monitor cable is not plugged in properly or the graphics card is not plugged in properly.