Looking for the trick of burning the machine, how to burn the machine?

This is a post from an old burner in the bar, just for reference.

Personally, I recommend that ordinary headphones can listen naturally, and it is not easy to distinguish if you deliberately boil them.

You can use a more frequent ** natural pot, generally at a normal volume (50%-70% volume is recommended) for about 48 hours or longer, you can also use white noise or burn-in software and other signal sources. Cook continuously for about two hours, stop for a few minutes and then continue, keeping the volume not too loud to avoid irreversible physical damage to the diaphragm of the earphones.

煲机 (bāojī) is a measure to quickly stabilize the aging of equipment. Some components such as transistors, integrated circuits, and capacitors are unstable when they are brand new, and they can gradually stabilize after a period of use.

What does it mean to burn the machine, also known as the headphones, speakers, and the machine?

"Burn-in" means that the sound quality needs to be stabilized after a period of use. If you listen to it for 1 hour a day, it will take about a few months for the sound to basically stabilize. Then this month is the "burn-in" period.

Proper burn-in will not damage the headphones, but will only accelerate the stabilization of sound quality. The word "stable" is used here, not "improved", and some headphones (speakers) don't necessarily boil better than brand new.

However, a step-by-step and efficient burn-in machine can greatly shorten the run in time and bring the equipment into the best state faster, and on the other hand, it can also work in the full range of equipment or speakers to warm up in a more comprehensive and balanced manner. However, after the special burn-in process, there is still a significant improvement in the sound, which is because most of the most commonly listened to ** frequencies do not cover each frequency range from the highest to the lowest, even if there is coverage, then the frequency and time of ** are difficult to average, so from the perspective of burning, it is unfinished, and there is also a situation that the equipment that has not been used for a long time can be restored as soon as possible through the burn-in. Naturally, the work efficiency will also be greatly improved!

To burn the machine is first to choose the right software and ** record, which can be divided into two categories, the first stage of the burn-in when the application of a class of sound CD signal disc to carry out, this sound CD record is pink noise, also known as pink noise, the important thing is a wide range of frequency, from the lower 20hz to the highest 20khz should have, continuous from the highest to the lowest continuous**, this kind of sound disc is not difficult to find, many video stores have sold similar audition cd records or burn-in CDs. For example, the 8th segment of the old XLO test disc released by Sheffield Lab can be called a classic in the sound of burning, in which a signal interleaved contains the frequencies of each segment, although it is quite noisy and ugly, but the effect of burn-in is ideal.

The second stage of the burn-in is to burn the machine with the second type of disc - the first disc with a comprehensive frequency width and effect, the first stage can be said to be like a martial arts practitioner to open up the "two pulses of Ren Du", the purpose is to open the full frequency, and the focus of the second imitation of the Mao Kai stage is to boil out the ** sense and taste. The selection of CD repertoire can consider classical music, symphony, opera, jazz, traditional folk music and pop**, etc., not to stick the speaker or headphones for a long time in a single ****, but must be mixed, each of which must be tried repeatedly.

Finally, we have entered the third stage of the final burning, which is carried out with our favorite type, so that the equipment can be more fully used in this type. At this stage, the burn-in time is also knowledgeable, the more high-end products, the higher the sensitivity of the equipment, the more burn-in time each stage should be, in terms of ordinary equipment, generally speaking, the burn-in time of each stage should not be less than 40 working hours.

Gradually from the first factory too tight, to slightly loose, a process of "relieving the muscles and activating the wind", is also a process of aging the diaphragm. "Cooking headphones" refers to such a process, not a method. Therefore, when you are listening, you are not only cooking, you are listening to the song with it, no matter what you listen to, it is such a process of "relaxing the muscles and activating the body" for him.

Therefore, after getting the new headphones, just take them directly to listen to **, at this time, the Ling Argument Pin needs to pay attention to the fact that the new headphones should not be too loud, but you don't have to care too much, as long as it does not exceed the volume that you can usually accept.

Cooking headphones can indeed make the sound of the headphones sound good, and the natural pot (both natural listening, through normal listening to the song to cook) and hard pot (long-term white noise, symphony, etc.), the actual principle is the same, but the new headphones themselves are tight, not in the best working condition, but to be used for a long time**white noise or a variety of so-called "burn-in"**, I don't know whether this is the maintenance of the headphones or torture.

Therefore, take the new headphones, listen to them directly, enjoy the ** at the same time, slowly feel the changes in the headphones, and it is also a very interesting thing to fail.

Burning principle: the main purpose of the headset is to make the mechanical system of the headphone a rapid aging process, the sound system of the dynamic headset is driven by the voice coil diaphragm, and the diaphragm is fixed on the frame of the headphone, theoretically speaking, the diaphragm movement should be a piston (vertical) movement, which requires the edge of the diaphragm to have a larger compliance, the pot is the pot here, the edge of the diaphragm of the new earphone is relatively tight, the elasticity is large and the compliance is small, the earphone is to let its edge move, the sound is not so tight.

Here's how to burn the machine:

1.Use a softer ** (white noise, red noise is recommended), let the headphones soothe for 10-30 hours at a lower volume, take a group of four hours, and stop for about ten minutes before cooking.

2.Use ordinary ** (except rock and dance music) to boil for 100-200 hours at medium volume, four hours as a group, and stop for about ten minutes before boiling.

3.It should be noted that the teasing is that you can't laugh for a long time, and the cooking machine pays attention to "asymptotto".

4.In fact, it's just like when you usually listen to **. Although it will be slower, the sound quality will gradually become better.

Here's how:

Time. After a week, the sound quality will be at its best.

You have to listen to the headphones for a certain amount of time and use up the battery.

The specific steps are as follows:

Step 1: When you get a new earphone, you need to make the diaphragm loose and not jump tightly.

As we all know, the general headphones are dynamic open coils, and the principle of sound generation is that the coils emit magnetic fields of different sizes, thereby pushing the diaphragm and using the amplitude of the diaphragm to produce sound. In other words, the final formation of sound is emitted by the vibration of the diaphragm, which we often refer to as the diaphragm of the earphones.

The second step is to make an aging headphone (which refers to the aging of the mechanical system in the first step) be able to adapt to the sound of various frequencies as soon as possible, so as to produce better sound.

We generally have a preference for listening, either more treble or more bass, even if we listen to everything, some frequencies are rarely used, which is the key to our beautiful sound. The only way is to use software, select the signal generator, and then put it on for 3 hours in a row, and cook it if you have time, and it is OK to cook it more than ten or twenty times.

As we all know, new cars, machines, etc., have to go through a call before normal use"Break-in"The internal mechanical devices are fully coordinated and cooperated, and they enter the best state in advance. Similarly, the push unit of the headset (the speaker inside the headset) is also a mechanical device, to be precise, it should be a semi-mechanical, semi-electronic combination, mainly composed of a voice coil, a diaphragm, a positioning ring (a metal ring that holds the diaphragm), etc.

The mechanical part belongs to the paralytic system, which includes the diaphragm and the voice coil fixed to the diaphragm. A conformity component can be equivalent to a capacitance in an electronic component, where the capacitor stores electrical energy and the diaphragm and voice coil store kinetic energy. The size of the headphone unit is equivalent to the parallel value of the two capacitors, the diaphragm and the voice coil, which is the key to determining the quality of the sound.

The material used in the diaphragm and voice coil is a high-compliance material, and its internal molecular structure is unstable in the early stage of finalization, so the compliance size is also unstable.

If you burn the machine, the low-end headphones are not necessary, there is an improvement but not obvious. If you really want to cook, I recommend a natural cook, that is, put it in general**, for a long time but softly. Of course, there are also cooks on the computer with burner software, which is fast but easy to cause injury.

If you don't want to buy more than 300 headphones, the 420 is enough.

Burning is a kind of life, and burning is an attitude.

You can cook it as much as you want, find more songs with different genres, and remember that the volume can't be turned on too much. The most taboo is full horsepower as soon as it comes up, you just wait to cry. The volume should be gradual, but it should not be on at any time!

The easiest way to use the Edifier box software is available on the official website.

When new headphones arrive, they are often not satisfied with the sound quality, and even doubt the quality of the headphones for a while. In fact, don't worry, new earphones are like new cars, they need to go through a run-in period, so how to burn the machine correctly? See below.

1. Quick burning: It is the pursuit of efficiency for the cavity, and this method can be used when you hope that the headphones can achieve the ideal effect as soon as possible. Generally, it is achieved through **white noise, pink noise, cyclic Wu Bei shout**, the volume should not be turned on too much, and rest for a few hours every day.

After a week or so, the effect will almost be there.

2. Natural burning: You don't need to deliberately listen to anything, use medium to medium volume, and listen to your favorite type. Listen slowly, it will naturally be pleasing to your ears after a long time, and the sound quality of the headphones will become more and more ideal.

3. Software burn-in: In order to make burn-in easier, there is also special software for burn-in. With the software, the rolling burner will become programmed, and it will automatically ** all kinds of burn-in sound sources, and it can also make the headphones achieve the ideal sound effect faster.

The above is the correct way to burn the machine to share with you, and those who need it quickly understand it, I hope it can help you.