How to change the coordinates of a specified point to a specific coordinate in CAD

Here's how:

1. Enter the two known coordinate values on the drawing that needs to be marked with coordinates. The input method is as follows: click the straight line tool or command, enter the y coordinate value of the first coordinate point, then enter the comma, then enter the x coordinate value, and press enter.

Then enter the y-coordinate value of the second known coordinate point, enter the comma, enter the x-coordinate value, and press enter.

<>2. At this time, there is an extra straight line on the desktop, which is the correct coordinate position at both ends of the straight line. If the graph becomes too small to be seen, enter Z, press Enter and enter E, Enter, and you will see the line.

3. Click "3D Operation" in the Modify drop-down list in the menu bar"Alignment", then use the mouse to select the entire drawing, specify the first source point (that is, the first point of the known coordinates), click once, then click on the end corresponding to the line you get, click on the second source point (that is, the second point of the known coordinates), and then click on the other end of the line you get, and press Enter. At this point, the direction of the drawing has also changed, and the whole operation is complete.

The same goes for changing the coordinates to 0,0,0 points to a specific coordinate. Refer to the following below:

1.Click the initial coordinates to see the coordinate points as shown in the following figure. This is shown in the figure below.

2.Type "ucs" in the command bar. This is shown in the figure below.

3.The cursor appears and selects the endpoint in the lower-left corner. This is shown in the figure below.

4.Select the x-axis direction, which is horizontal. This is shown in the figure below.

5.Then click on the xy plane at will. The origin is set. This is shown in the figure below.

6.Use the Coordinate View tool to confirm. This is shown in the figure below.

7.Finally, change the coordinates to 0,0,0. This is shown in the figure below.

1.Computer-aided design.

computeraideddesign) can design and produce part models that not only meet the requirements of design and use, but also fit the cam.

Processing. 2.The CAD system is an efficient design tool with parametric design functions. 3D solid models and 2D engineering drawings should be able to be converted and related to each other.

CAD software has a drawing file interface, which can support the conversion of a variety of drawing files, can read drawing files from other systems, and can also convert drawing files in the system into drawing files in other systems.

Move the point to the specified coordinates, and there are absolute coordinates in CAD.

The steps to move the CAD to the specified coordinates are as follows:

1.Double-click the CAD sheet icon you want to draw to open the sheet. Click the Shift icon in the modifier bar on the right side of the window.

2.Hold down the left mouse button to pull out a rectangular area so that the selected area contains the shape you want to move, and then right-click OK.

3.Move the mouse cursor to the base point you want to move in the figure, and click the left mouse button to determine the base point.

4.Move the mouse to move the graphic you want to move to the specified position.

5.Just click the left mouse button. This solves the problem of CAD moving to the specified coordinates.

1. First, let's open a graphic file. In the graph, we can see that the origin of the coordinates is located in the lower left corner of the graph.

2. To modify the coordinate system, we can click on the"tools"tab.

3. In the drop-down menu, click"Create a new PC", and then click"Origin"。

4. After clicking, the origin of the coordinate axis will follow our mouse, and we click the left mouse button at the desired position to determine.

5. After clicking, we can see that the origin of the coordinate system has been changed. The coordinates at this point are set according to our new reference.

6. If you want to switch to the original coordinate system, we can click on the tool again, and then click on the one named UCS below.

7. Then select the world in the UCS window that pops up, and then double-click or click the right side of the setting for Latest. When you're done, click"OK"。

8. Click"OK", we will return to the modified coordinate system.

1. First of all, open CAD in the computer, right-click in the blank space of the menu bar to check the annotation, as shown in the figure below.

2. Then in the options window that opens, use the coordinate tool in the annotation tool as shown in the image below.

3. Then click the mouse on the point to be labeled, and pull out the x coordinate horizontally, as shown in the figure below.

4. At this time, click the point to be marked with the mouse, and pull out the Y coordinate vertically, as shown in the figure below.

5. Then select the Y coordinate, and modify the text rotation parameter to 1 in the property table on the left.

6. Finally, as shown in the figure below, the coordinate labeling is completed.

Double-click the coordinates to display the data in the "Properties" modification text.

The specific steps are as follows:

The materials we need to prepare are: computer, CAD.

1. First of all, we open the required CAD drawing, click on the command bar in the lower left corner, enter "UCS", and press enter to confirm.

2. Then we click to select the line we want to correct in the pop-up window, and then click on both ends of the line.

3. Then we press the enter key according to the instructions on the command bar that pops up to confirm.

Create a UCS. UCS space, enter n. Click on the point where you want to create coordinates

Use the Move command to enter the origin coordinates for the second point or create a new coordinate system.

1. Draw a square in CAD without any corner points on the coordinate origin;

2. Click the "Move Command" on the modify toolbar, select the square you just drawn, and the first base point is on the four corners of the square;

3. Enter the "0,0" origin coordinates with the keyboard for the second point, and use it in the middleCommaSeparated;

4. The corner point of the square just selected has coincided with the coordinates of the origin; Oak Respect.

5. There is also a way to create a new coordinate system, redraw a square;

6. Click on the tool column in the menu bar at the top of the interface, select "New UCS" in the drop-down menu, find the "origin" of Liang Caoshen, and click;

7. Select the corner point you want to use as the origin of the curved and hidden coordinates, and click;

8. It can be seen that the coordinate origin has changed at this time.

First, open the CAD on your computer and draw a drawing using the rectangle in the drawing tool, as shown in the figure below.

Then enter ucs in the command line window and press enter as below screenshot shown.

In this case, specify the point on the x-axis of the coordinate system, taking the point in the lower right corner of the rectangle as an example.

Finally, specify the direction of the xy plane, click on the inside of the rectangle, the new coordinate system is set, the origin is at the lower left corner of the rectangle, and the coordinate system is established.

UCS command ah:

Start by drawing a right-angled coordinate system on the plane. (It is two lines perpendicular to each other, and the length of the line is customized.) ）2.

Then use the View, 3D View, Left (or Right) command, and the screen will show only one straight line. At this point, you will notice that you are in the new xy plane, and then draw this straight line (in fact, there is an invisible perpendicular line) in the new xy plane. The starting point of the perpendicular line should preferably be the origin of the original coordinate system.

At this point, you have established a spatial right-angle coordinate system. (You can use "3D Dynamics").

3.Type UCS. Space. The prompt command appears: "[New(n) Move(m) Quadrature (g) Previous(p) Restore(r) Save(s) Delete(d) Apply(a)?World (w)].

"New" means to create a new 3-dimensional coordinate system. This command I use the most. Enter "N" and the prompt command "Specify the origin of the new UCS or [Z-axis(za) three points(3) object(ob) face(f) view(v) x y z] <0,0,0>:

The most common thing I use is to select the z-axis, i.e. type "za", space. You can then turn on the object snap optional z-axis.

I don't need to talk about the other commands. Hehe.

In fact, sometimes you don't need to re-establish the coordinate system, and the switching function of the F6 button is enough!

Hello, I'll help you solve this problem! The operation steps are as follows: 1. Open the file you want to operate in CAD 2. Find the format window in the menu bar at the top of the interface, and click the dot style command with the mouse in the drop-down selection box, and a window will pop up in the interface.

We make some settings in this window, such as color, size, etc.3, after the setting is completed, we can directly click OK. After that, find the drawing window at the top of the interface, and click the point command 4 with the mouse in the drop-down box, and you can choose the position of the point you can choose according to your specific requirements. Or you can also directly enter the coordinates you want in the command in the lower left corner, you follow my steps to try it, and if you have any questions, you can give me feedback in time!

1. First of all, we will open the CAD in the computer.

2. Enter the user interface, click the file option, select the "Open" button in the drop-down bar of the file, and open the required CAD drawing in the pop-up interface.

3. In the "Instrument" option in the upper function bar, click to select "Search Point" to find the given coordinate point in the drawing and display it in the window.

4. A dialog box will pop up in the interface, in the pop-up "Display Point" dialog box, enter data at the position of each axis, and click the "Display" button to find the coordinate position.