After the router is connected to the third network cable, the network speed is very sluggish

The third person's computer was poisoned.

That means that the network is unimpeded, and there may be a problem with the wireless router and computer settings.

Because the network cable is directly plugged into the Internet, an Ethernet card device is used, and a wireless network card device is used when using a wireless network.

If the router is abnormal, reset the key as soon as possible, at this time the router has been restored to the factory default, and it needs to be set again.

First of all, it is necessary to keep the front-end equipment (modem) intact and the network unblocked.

After pressing the router's reset button, wait until all the lights are on together, indicating that the reset is successful.

Enter your IP address, username, and password in the address bar of your browser (prompted on the back of the router).

After following the router's setup wizard, you can surf the Internet normally.

Resources.

First of all, my prompt to check the wireless settings, in the final, the wireless router control platform has the function of static IP, you see if there is a network card address you don't know (that is, a sequence of numbers + letters)? (You can record your network card address when you only surf the Internet yourself,And then pay attention to it,If there is no unknown network card address,It means that you have not been rubbed on the network) and then turn on IP control in the LAN function,Set the number of broadband M (1M=1000K conversion,Not a theoretical value) and then set the network speed in each IP segment (2 kinds of guaranteed lower limit and control upper limit),You don't want to be used IP segment you set it to 1KB,Effective IP is。。 Finally set your own book into one between them.,And bind.。

After you finished these things yesterday, if you still can't surf the Internet, you can use a 360 speed tester or a speed tester in telecommunications** to see what your effective **speed is? The network speed loss of optical fiber is less than 5%, even if it is suitable, when everything is right, the problem may appear on your network card, of course, the network card driver will sometimes strike, you can also try to reinstall the network card driver with the system disk, I hope you can solve the problem as soon as possible.

How long has the operating system been used? Replace it and take a look? There is also a drive upgrade for the wireless network card.

If some of them use P2P software or the like, it will cause large network latency and network instability.

It's important that your router has a speed limiting feature.

Home Network Environment Cabling:

1. There is a telecom cat: the telecom cat --- router WAN port; The LAN port of the router --- the computer;

2. No telecom cat: network cable --- router WAN port; The LAN port of the router --- the computer;

Set up router dialing:

Automatic acquisition of computer IP and DNS settings;

1. Enter the router. In the [Setup Wizard], select [PPOE Dialing] (some are ADSL Dialing), enter your Internet username and password as prompted, and save;

2. In [Network Reference Return] --WAN Settings], select [Normal Mode], and select [PPOE Dialing] in the three options of [Connection]. The next is to select [Auto Connect], Save, and Exit;

3. If you want to use wireless wifi, your router must have a wireless router function, in the settings, turn on the wireless routing function, here, the wireless signal signal to change to one of them. The strongest anti-interference. You can also set a password for your Wi-Fi connection.

As long as the signal is good, there will generally be no problems, choose a reliable quality router, and secondly, no matter how many routers you have, broadband is shared, how many m or how much you have, your router, one more, just one more interface, if it slows down, it means that He Shu has a large number of users, needs bandwidth growth, or the signal is unstable.

1.First, connect the computer from the LAN port of the router to match this, and change the IP address of the slave router to a different network segment address, as long as it is not in the same network segment as the main router. For example, most router addresses are, and we just need to change from router address to one;

2.Then turn off the DHCP function from the router in the settings;

3.Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

Yi'an Media Technology replied, after success, you have to reply, you have to like, and follow,**.

I'll give it a look. Today's routers are generally 100 megabits, even gigabits, and 10 megabit of acres have been changed, but now the commonly used super five network cables are 100 megabit bandwidth, plus line interference, loss, there may be slow network speed. The Category 5 network cable I used before at home, and the Category 7 shielded network cable I use now, I personally feel that it is much more stable, you can also try it.

Book of Annihilation.

How are you two connected? If it's shared, it's definitely card. It is recommended to install a router.