There are broadband and wireless routers, is it necessary to set it up in the notebook after connect

The connection of the wires, depending on what you said, should be connected.

1. First open the browser and enter the home page of the router (there should be in the manual or at the bottom of the router, mostly or.

The username is mostly admin, and the password is mostly empty).

2. Go to the network connection, or Internet installation, and look for something similar to what I said.

3. Generally, there is a setup wizard, or a quick setting CD, and enter the corresponding things in the place where you need to enter the Internet and password according to the prompts. If it is unlimited, you can choose to always connect, and if it is time-limited, you can choose to connect on demand or manually.

4. Set the name and password of the wireless in the advanced wireless settings or wireless installation settings.

5. Connect the laptop to your wireless network, and set the IP of the wireless network card to automatically obtain it (the router can be set to be fixed after you are familiar with it).

It's generally OK.,The general wireless router has a data light.,If it's connected to the Internet, it's not the same color as if it's not connected.。

Generally speaking, when you turn on the wireless card on your laptop, you can find the wireless routing network.

If you can't find it, practice it with network cable and wireless router first.

Then use IE to enter.

You are now on the management page of the wireless router.

Turn the wireless function on.

By the way, set a password.

And then it's fine.

The router needs to be set up to access the Internet in order to connect to the broadband properly.

Required: Laptop, router, direct cable.

2. Usually the back of the router is labeled, with the router login address, login username and password. If your router has changed its login address and you have forgotten it, you can reset your router and try again after resetting it to factory settings.

Here's an example:

3. In the router management interface that appears, enter the login username and password, and click Login.

4. On the left side of the router management interface, in the function menu, click Internet. Choose different connection modes depending on the way you access the Internet. Generally, if you are connected to a broadband modem, select PPPoE dial-up and fill in the broadband user name and password. When the new modem comes with a dial-up, select Dynamic IP.

5. If the router is a wireless router, set the wireless network name in the wireless settings.

6. Set a wireless password. Click "Done" and the router will automatically restart to complete the setup.

First of all, if you have a wireless router, then turn on the power supply first, then plug in the network cable, plug the incoming line into the WAN port (usually the blue port), and then plug in any LAN port connected to the network cable connected to the computer.

2.After doing these things, then you will see that there is an address and account password behind the router, and after connecting, enter the address you see in the router in the browser, generally of course, if your home is using ** online network, then you have to prepare an additional modem, commonly known as "cat").

3.Then enter, enter the corresponding account and password, generally the new ones are admin.

4.After entering the operation interface, you will see a setup wizard on the left, Attack on the entry (usually it pops up automatically.)

Click Next, enter the Internet access method settings, we can see that there are three Internet access options, if your home is dial-up, then use PPPOE. Dynamic IP can be used by plugging the computer directly into the network, and there is a DHCP server on the upper layer. The static IP is generally a private line or something, or it may be a cell bandwidth, etc., and the upper layer does not have a DHCP server, or wants to fix the IP.

5.If you choose PPPOE dial-up Internet access, you need to fill in the Internet account number and password, and you will have an account number and password when you open broadband, and you can fill it in.

6.Then the next step is to enter the wireless settings, we can see the channel, mode, security options, SSID, etc., generally SSID is a name, you can fill in as you like, and then the mode mostly uses 11BGNFor wireless security options, we need to choose WPA-PSK WPA2-PSK, which is so safe that it will not be hacked and rubbed by the network.

7.Click Done, and the router will automatically restart, and the interface that will appear after success.

Like desktops, you need to go to the router's settings interface to set it up, and the specific steps are as follows:

1.Open your computer's browser, enter it in the address bar of your browser, and press Enter.

2.At this time, the login box of the route appears, enter the password of the route and the password (lowercase admin) in the login box, click OK, and you will enter the route setting page.

3.Click "Setup Wizard", enter the broadband account number and password in the and password field to complete the setting.

The router setup requires a computer to be connected to the router.

When you connect to a router computer, you don't need a broadband connection, the connection is done by the router.

good luck

After the computer is connected to the router, open http: and follow the setup wizard to set it up

Of course, it must be connected to the route, please refer to the manual for details!! It's simple.

You need to connect the computer to the router, not the broadband connection.

1.Router connection;

The network cable from the cat is connected to the router WAN port, and the two computers are connected to the LAN port (or port), and the corresponding light should be on or flashing;

2.Router Settings:

Enter Yes in the IE address bar, the username and password are admin, click on the setup wizard after entering, select PPPoe, and set the broadband account password.

3.Electron settings:

Set the IP of 1 computer to, the other 1 to, and so on, the subnet mask is all the same, the gateway is, and the DNS is also filled.

Open your browser.

Enter the password and account number, both admin

When you surf the Internet on the computer, you need to dial the account password, and the operation is as follows:

Network Parameters - WAN Port Settings - Dial-up Internet Access - Enter the account password given to you by the operator, save it, and restart it.

You can plug in the network cable directly on the computer side, no need to dial, no need to set up, the operation is as follows:

Network Parameters - WAN Port Setting - Dynamic IP Acquisition, Save, Restart to Access the Internet, and then repeat steps 1-3 to set the wireless password. Otherwise, everyone else will be able to use your wifi

There is no need to set up a broadband connection to your computer after installing the router. The router has a virtual dial-up function, and the device connected to the router can directly access the network after setting.

How to set up PPPoe broadband dial-up on a wireless router:

1.The router is connected to the network.

2.The system is connected to the router.

Turn on the wifi of the computer, search for the default wifi name of the router (the nameplate on the back of the router is written), and connect to the wifi network. The first time you use the router, you generally don't need to enter the wifi password.

3.Go to the gateway page.

Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface. (This interface will pop up automatically for new routes).

For broadband dialing, please select PPPoE mode.

Enter the Internet access account or password to set the broadband account password.

Select Automatic connection as a connection method.

The steps to access the Internet on the router are as follows:

1. Connect the devices correctly, as shown in the following figure:

2. First of all, select automatic acquisition for the Internet protocol settings of the computer.

3. Then set up the router.

1) Open IE, enter the address in the address bar or the address on the back of the router), OK, and ask for the dialog box to enter the username and password;

2) Enter "admin" in the username and password text boxes respectively (different routers may be different, see the instructions on the back of the router), confirm, and open the configuration interface of the router;

3) In the router settings interface, follow the prompts, select "PPPoe Protocol" (note not to select dynamic and static), then enter the broadband account and password, select "Auto Connect" in the advanced options, click OK, and restart the route to access the Internet.

Your wireless router is still yes! Wankou lankou is not wrong! Are the routes set up correctly!! Does your desktop work properly?

1. Check the ** behind the router: generally, there are.

2. Enter ** in your browser.

3. Enter your username and password. Generally, the default is admin4, select the "Setup Wizard" to set the Internet account and password5, and restart the router.

This problem is easy to solve. Are you using telecom adsl, if so, the question is too simple.

If you use the starry sky to dial the Internet quickly, it is ADSL. Then I'll teach you how to use Router to surf the Internet.

First of all, you don't need to use the router to connect to the two computers, you first use the original desktop computer to connect to the Internet with the correct dial-up.

Open: Control Panel Performance and Maintenance Administrative Tools Event Viewer System.

When you first connect to the network, the first thing in the system is your telecom encrypted account, and the password remains the same. It will display + English or number + area name + ** number, the user's connection network information. This is your correct account number, which is the correct account number that the system automatically dials.

The second step is to set up the router, connect the two computers with the router and use IE to enter, enter **Yes. Generally, the username and password of the router are admin. Go to the setup wizard and set a dial-up username with the account number and original password generated by the event viewer.

In it, it is set to automatically dial the number when it is turned on and disconnected.

The third step is to set the IP. Open Network Neighbors View Network Connections Local Connection Properties Internet Protocol Properties Automatically Get IP, DNS Address Option Select OK.

Turn on the wireless connection on your computer - just click on the connection if you have a signal.

<>2. Then open the browser of the computer and enter the login address and login password of the router. (For the specific login IP and password, you can look at the label on the back of the router).

3. After entering the router settings page, fill in your broadband account and password.

4. After the successful setting, a prompt will appear for successful setting, and restarting the router will take effect at this time.

<>11. Click OK to complete the setting.

3. After completing the above steps, fill in the password accurately, and then log in.

4. After completing the above steps, select and click on the "Setup Wizard" option.

Connection method, routed WAN port and modem connection. The AN port of the router is connected to the computer. This completes the connection.

Setting method: Enter enter enter in the address bar of the browser, the login box of the route appears, enter the routing and password (lowercase admin) in the login box, click OK, and then enter the routing settings page, and then look at the figure and then enter the broadband account and password in the setting to complete the setting.

It's set up just like a regular desktop.

If you are connected locally, see if your gateway address is the IP address of the router? Generally, the mask of household equipment will not change, so you can use it directly, or is your DNS server set up? If you don't have DNS server data, ask your broadband provider.

It is recommended to fix an IP address for the notebook. It's okay to use DHCP sparingly, that will slow down the boot speed.

Most importantly, does your wired router have access to the Internet on its own? If it is dial-up, check whether the router has dialed up successfully.

Configuration steps: Set up the PPPOE dial-up of the router, use the account number and password given when handling broadband, and pay attention to distinguish between "uppercase and lowercase letters".

The WAN port of the router is connected to the network cable of the broadband modem.

The LAN port of the router is connected to the computer.

The computer network connection is set to "Automatically get an IP address, automatically get a DNS server address".

The computer can no longer dial numbers.

You can go directly to the Internet, and you can use it with a wired Internet cable.

If you have a problem with your routing settings, try typing it in your browser.

Username and password admin,Most of the routes enter the settings page like this.,And then it's a little more complicated.,You refer to the following web page.。

If DHCP is turned on on the router, the laptop can automatically obtain the IP, look at the router settings.

Take a look at the router manual first, and then enter the router through the network cable (generally the router IP is, after entering, you can set it up, and after the setting is completed, you should be able to access the Internet :-) I wish you success, brother!!