Body stability system failure, body stability system fault light is on, how to solve it

Hello questioner! If you post the **, it is the actual situation of your own car, then I can tell you that this is definitely not a special ESP body stability system turned off!

Because I noticed that your abs alarm light is also on! The ABS lamp and the lamp of the stabilization system are lit at the same time, then there is only 1 reason.

It is that the ABS chainring, and the Hall sensor are too dirty, and there are a lot of impurities that stain the sensor, resulting in the inability to have a normal pulse signal output! The wheels need to be removed, the chainrings of the ABS and the Hall sensors need to be found, and then they need to be cleaned carefully! The fault can be solved!

You just need to drive the car to the 4S shop and ask him to update it for you or find out the reason for it on the computer. Or maybe you accidentally pressed that special.

The body belongs to the stability system, and it is generally not buttoned, and the car clothing is with you. If you press that key, that body maybe, uh, no, the system may fall.

This fault code is that the throttle valve actuator is stuck in the closed position, and the ECM sends a command

The throttle opens.

dao, but the actuator is stuck, if the electronic throttle valve right insurance is no problem, the wiring harness is no problem, measure the needle angle 1 and 2 for the throttle motor coil, the resistance value is not normal to replace the throttle [the car has a problem, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Hello, this is mainly due to the failure of the electronic control system in the body stability system, it is recommended that you find a repair shop to read the fault code with a decoder, and then repair it.

That thing has a body stability switch in the row of double-flashing switches, and you guess you touched that switch! The stability system is turned off, so it's always on! You press that switch again, turn on the stabilization system, and the light goes out!

Are you sure if you turned off the stability system yourself! If there is a fault, go to the store and read the fault**!

You may be ESP system turned off, see if the switch is on, or ESP is faulty!

Hello, first of all, did you turn off the body stability system?

It is advisable to take it over to see if there is a fault or if the sensor is broken.

Upper snow chains. What kind of light is that lamp?

Vehicle stability system failures are failures in air intake, ignition, fuel systems, and related components.

The body stability electronic control system has good power performance, short acceleration time, if the acceleration reflects hysteresis, poor acceleration, idle ** motive is unstable, etc., indicating that the electronic control system has a fault, should be repaired in time.

1. Failure of the air intake system.

The air intake system is composed of air filter, air intake branch, sensor, idle device, boost control, etc., and its sensors include: air flow sensor, air pressure sensor, throttle position sensor, intake air temperature sensor, cooling temperature sensor, etc., the failure of these related components will affect the normal operation of the engine.

2. Throttle failure.

The function of EFI idle control is to realize the rapid warm-up process after the engine starts; The second is to automatically maintain the engine idle speed in various target speeds of stable operation, idle control is basically to control the throttle opening, if the throttle valve carbon deposit is too much, so that the idle control valve in the same opening, the air intake is relatively reduced, resulting in idle instability.

3. Fuel system failure.

The fuel system is one of the most important systems of the electronic control system, the main role is to provide sufficient fuel to the engine, the fuel from the fuel tank through the oil pump pressurization, through the fuel filter, to the injector.

If the injector is faulty, the fuel pressure is too low or too high, which will affect the entire electronic control system, which will lead to poor acceleration and unstable idling.

I also encountered this problem, found a lot of repair shops to check, all said no problem, and finally found the 4S shop where the car was purchased, a teacher said that there was a problem with the battery and needed to be replaced, I couldn't figure it out at the time, is the battery related to this? He definitely said that this is the problem, and after changing the new battery, it is completely fine. FYI.

Hello, your anti-lock braking system abs, it is possible that he has a malfunction,

The body stability system is very important, the body stability control system is faulty and solved: the actuator of the car throttle judgment is stuck and the shut-off part, the ECM sends out a command to open the car throttle, but the actuator is stuck, if there is no problem with the electronic throttle commercial insurance, there is no problem with the electronic wiring harness, and the needle angle 1 and 2 are measured for the car throttle motor coil, and the resistance value is abnormal to disassemble and replace the car throttle; If there is a common fault in the ESP system of the electronic control system, it is recommended to go to the auto repair shop to load the engine fault code with the ** decoder, and then replace it.

The ESP system consists of a control module and steering sensors (which detect the turning angle of the steering wheel), a wheel sensor (which detects the speed rotation of each wheel), an anti-detection sensor (which detects the rotation of the car body around a vertical centerline), and a lateral acceleration sensor (which detects the centripetal force of the car after turning). The throttle actuator of the car is stuck in the shutdown part, and the engine controller of the car pushes a command to open the throttle valve of the car, but the actuator is stuck in the shutdown part. If the safety of the electronic throttle is normal and the electronic wiring harness is normal, accurately measure the angle of view 1 and 2 of the needle of the motor coil of the automobile throttle, and replace the throttle if the resistance value is abnormal.

There are common faults in the ESP system. It is recommended to go to the auto repair shop to load the engine fault code with the ** decoder and then repair it. The ESP system consists of a control module, a steering sensor (to detect the angle of view of the steering wheel of the car), a wheel sensor (to detect the rotation of each wheel), an anti-detection sensor (to detect the movement of the vehicle body around the vertical axis), and a lateral acceleration sensor (to detect the centripetal force after the car has turned).

When the vehicle is driving in a corner, if the front tire is the first to achieve the adhesion limit value, it will often cause a "drifting" situation, and then the driver can not reduce the turning radius of the road no matter how he plays the steering wheel, and then he can not follow the track, and the turn becomes invalid, which is called oversteer.

If the rear tire is the first to reach the adhesion limit, it is prone to "drifting", and the vehicle itself will become unstable, and the vehicle will be quickly pulled to one side, which is called oversteer. The function of the stability control system is to oversteer and cause the car to move to both sides; Or when the car crosses the center line of the road due to oversteering, or even when standing in place and turning, the computer is used to control the power response of the automobile engine, and change the braking torque of any one or more wheels, so that the car causes the corresponding rotational torque, so as to clear the situation of oversteer or oversteer, and improve the reliability of driving dynamics.

When the stability control system of the vehicle fails, it is necessary to go to the repair shop in time to repair the trouble, but if you just accidentally touch the traces on the vehicle, you can turn it on again.

There was a malfunction of the electronic control system in the body stability system. It is recommended to find a repair shop to use a decoder to read the fault code before repairing.

I think if the stability control system of the car body fails, you should take the car to a 4S shop for repair.

ESP system failure means that the function of this system can fail, can not work normally, and needs to be tested and repaired as soon as possible

1. Electronic Stability Program System (ESP) is the abbreviation of English ElectronicsTabilityProgram, translated into Chinese as "Electronic Stability Program";

2. The function of the ESP system is to monitor the driving status of the car, so that the vehicle can avoid deviating from the ideal trajectory when there is understeer or oversteer when urgently avoiding obstacles or turning;

3. It is a combination of ABS (anti-lock braking system), BAS (brake assist system) and ASR (acceleration and anti-skid control system), which is more powerful.

If the stability control system fails, it means that the vehicle's stability control system is turned off or fails. If you accidentally press the ESP, OFF button on your vehicle, you can turn the ESP back on by pressing it again. If the ESP and OFF lights are on due to the failure of the Ling Annihilation system itself, it should be repaired in time.

The solution to the failure of the body stability system is as follows:1The throttle actuator is stuck in the closed position, and the ECM gives a command to open the throttle, but the actuator is stuck in the closed position.

If the electronic throttle is safe, the wiring harness is fine, the measurement needle angle 1 and 2 is the throttle motor coil, the resistance is abnormal, replace the throttle; 2.There was a malfunction of the electronic control system in the body stability system. It is recommended to find a repair shop to read the fault code with a decoder, and then repair; The system consists of a control unit, a steering sensor (to monitor the steering angle of the steering wheel), a wheel sensor (to monitor the speed of each wheel), a side slip sensor (to monitor the state of rotation of the body around the vertical axis), and a lateral acceleration sensor (to monitor the centrifugal force when the car is turning).

Millions of car purchase subsidies.

Body Brother Brigade Stability System Fault Solution:

1. The method of turning off the ESP body stability system: the button is marked with the word "ESP", and the indicator light will light up after pressing it, indicating that the ESP has been turned off;

2. The method of opening the ESP body stability system: the button is marked with the word "ESP", and the indicator light will light up after pressing it, indicating that the ESP has been opened;

3. SP system refers to: to prevent the vehicle from longitudinal and transverse slip that we do not expect when accelerating or braking. It is an active safety system that handles all kinds of abnormal situations, and whenever the ESP recognizes that your operation is inconsistent with the actual movement of the vehicle, it will choose the wheels or engine to intervene to stabilize the vehicle.

But the active safety provided by ESP has, accidental risk driving.

There are many sensors involved in the body stability system, so the general cause of the failure is the sensor, which may be the loose connector, the sensor function failure, or the false alarm, etc. When we find that the ESP light is on during driving, we need to slow down the driving speed, avoid excessive steering, and quickly find a nearby repair shop for maintenance.

The body stabilization system is mainly used to deal with emergency evasion obstacles, which is the risk of continuous steering and loss of control caused by tail flicking. When emergency avoidance, ESP intervenes to increase the rotational force of the driving wheel; When there is a tendency to flick, the ESP brakes the other wheel to reduce rotation, helping the vehicle to comply with the driver's intention to steer in distress.