How to boil the plaster and how to make the plaster

Here's how:

1. Stir-fry Huangdan. Put the yellow dan in a clean iron pot or copper pot, fry it until the water in the dan is exhausted, loose to the degree, and use a spatula to keep stir-frying.

2. Oil refining. Put the sesame oil without alkali into a clean pot, boil the flowers, and then change to a simmer, at the beginning the gas of oil and water will rise straight, and then after a while, the gas will rise to the pot, urgently use bamboo chopsticks to drop oil into the cold water, into the beads do not disperse, for the oil refining has become.

3. Fire up and down. At this time, continue to boil the oil with a slight fire, slowly put the fried Dan into the boiling oil, stir clockwise with a locust wood or willow stick, the oil will overflow bubbles, and smoke will come out, and when the smoke is slightly exhausted, it is urgent to use bamboo chopsticks to drop oil into the cold water for three or four drops, slightly into beads, and wipe the water with beads. Try to pinch with dry hands, so that you are not tired of your hands when you stick to them.

Hurry up and stop the fire. 4. Add the medicinal surface. After the oil is slightly cooled from the fire, the medicinal noodles are slowly added to it, stirred with a wooden stick urgently, and the oil is leveled, then add expensive and fine medicinal noodles.

5. Spread plasters. Urgently put the plaster that has not yet cooled up with bamboo chopsticks, with the size of the cloth, with the center of the bamboo chopsticks point cloth for a clockwise spread, then the plaster has been completed.

The production of the paste recipe goes through several processes such as soaking, decoction, concentration, paste collection, and storage. 1 Soaking Check the complete medicinal materials first, and pick out the gelatinous drugs and put them separately. Then put all the other medicines into a clean casserole with a comparable capacity, add an appropriate amount of water to soak the herbs, so that they can fully absorb and expand, and then add water to about 10cm above the surface of the medicine, and soak for 24h

There are several steps:

Ingredients: According to the prescription, the drug is weighed accurately, and the medicine that needs to be processed is prepared according to the law for later use, and the fine material that needs to be mixed into it is ground (more than 80 mesh) and reserved (used when spreading plasters).

Fried Dan: Put Zhang Dan (lead tetroxide) in an iron pot to heat, stir-fry until the brick is red, take out and let it cool for later use, the purpose of fried Dan is to remove the water in the Dan, and prevent the operator from being injured due to the bursting of the oil refining containing water in the Dan at high temperature.

Explosives, according to the size of the medicinal materials, the different textures of the prepared medicinal materials, respectively, poured into the oil for heating treatment, until the explosion is dry (the retention of the property can not all be fried into black charcoal) to remove the medicinal materials, filter the residue for later use.

Oil refining, oil refining is the key to boiling a good plaster, oil refining is not good can not make a good plaster, the fastest time for oil refining also needs hours, during this period to continue to use a colander to pick up the oil, (the purpose is to prevent smoke, cooling to prevent fire) to control the heat, refining until the dripping water into a bead (refining dripping water does not diffuse similar to the formation of a small bead).

Under the Dan, there are two situations, one is the fire and the next is the fire and the other is the fire and the other is the fire and the Dan. There must be two people to operate the Dan from the fire, the refining oil that is refined to the dripping water into beads is quickly moved from the stove to the pot rack, the person holds the fresh wooden stick, and the person through the fine Luo (60 mesh) will be fried Dan evenly sprinkled into the oil refining, and quickly stirred, so that the Dan oil is fully combined, the Dan has yellow to gray-brown and finally to black, the oil is dripped into the water to test the plaster of the old and tender, to qualify, quickly trickle into the cold water and stir in one direction, with the hand constantly tearing and twisting into a fist-sized top, soak it in clear water, change the water twice a day. After 20 days, remove the water and dry it, dip it in talcum powder and seal it in a porcelain bottle.

Spread the plaster: take the plaster that has been removed from the fire poison and heat it at a low temperature to melt, add a finely ground fine material at 60 degrees and stir well, and the plaster can be spread.

I wish the sick a speedy day**!

The production process of traditional black plaster 1 Extraction of medicinal materials (boiling and removing slag): take vegetable oil and put it in a pot, put the medicinal materials into it after slightly heating, heat it and stir it continuously until the medicinal materials are fried until the surface is dark brown and the interior is browned. At this time, the temperature can reach 220 degrees, and the residue can be removed with a wire sieve after frying, and the oil after the slag is medicated oil.

It is best to use a copper pot for the pot, and a special high-temperature thermometer can be used to control the temperature, which is sold in medical equipment stores) 2 Oil refining: Take the above medicinal oil and continue to refine, wait for the oil temperature to rise to 320 degrees (it must reach the temperature, it is very critical), and switch to medium heat. The heat of oil refining:

One is to look at the thermometer to reach the specified temperature; The second is to look at the oil smoke, which starts to be light cyan, gradually becomes black and thick, and then becomes white smoke, and the white smoke goes straight up when there is no wind; The third is to look at the oil flowers: at the beginning of boiling, the oil flowers are mostly near the periphery of the pot wall, and when the oil flowers gather to the pot, it is a degree; The fourth is to see the dripping water into beads: take a little medicinal oil and drop it in the water, and do not spread out into beads.

This level is the most difficult, you must refine the oil to the dripping water into beads, you must pay attention to fire prevention, the temperature is too high) 3 Dan into a paste: After the medicinal oil is refined, it is removed from the fire, generally 500 grams of oil can be added to about 250 grams of Dan, and Huang Dan is dried and passed through a 100 mesh sieve before going down. A small amount of gardan, stirring as you go, be sure to stir in the same direction.

Stir into a viscous paste, the plaster is not sticky, the drawing is constantly good, too hard is old, too sticky is tender. 4. Remove fire poison: After the plaster is made, put it in cold water, soak it, change the water once a day, and the plaster will be formed after ten days.

5 Take the plaster and put it in a container, melt it in a water bath or simmer, mix the fine material in, stir well, take a certain amount of plaster with a bamboo skewer on kraft paper or plaster cloth, and musk and other particularly valuable medicines and volatile borneol, camphor, mint, etc. can be sprinkled at the end. Wash it before pasting**, take the plaster and bake it softly.

Here's how to make the plaster:

Raw material preparation: field.

7. Liquor, small gauze bags of traditional Chinese medicine, and medical tape.

1. Prepare the materials.

2. Put Tianqi into the bowl first, then pour in an appropriate amount of white sprinkles, remember that the liquor only needs to soak Tianqi powder slightly (you can also pour the wine first and then put the powder), soak for a day.

3. Soak for a day.

4. Put it into the prepared Chinese medicine pouch (you can also put it directly on the medical tape and stick it directly on the body).

5. Put the self-made Tianqi plaster directly on the sore spot after putting it into the prepared Chinese medicine pouch (you can also put it directly on the medical tape and stick it directly on the body).

6. After the plaster is made, it is recommended that one patch can be pasted for about 6 18 hours, and it is best to insist on more than 6 stickers, and then observe the changes in your sore spot and continue to use it.

Oil plus Guangdan is a plaster, but you also need to add Chinese medicine.

1. Vegetable oil, yellow dan, Huoxiang, camphor, myrrh, borneol.

2. Extraction of medicinal materials: take vegetable oil and put it in a pot, put the medicinal materials into it after slightly heating, heat it and stir continuously until it is fried until the surface is dark brown and the interior is browned. At this time, the temperature can reach 220, and the residue is sieved off after being tied, leaving the medicinal oil.

3. Continue to smelt the medicinal oil, wait for the oil temperature to rise by 320 degrees, and change it to medium heat. The medicinal oil is refined into dripping water into beads, and it is OK.

4. After the medicinal oil is refined, remove the Dan from the fire, generally 500 grams of oil can add about 250 grams of Dan. Add a small amount of Dan and stir in the same direction. Stir into a viscous paste, the plaster is not sticky, and it is best to draw the wire continuously.

5. After the plaster is made, add cold water, soak, change the water once a day, and the plaster is formed after seven days.

6. Take the plaster and put it in a container, melt it in a water bath or simmer, mix the fine material in, stir, take a certain amount of plaster with a bamboo skewer on kraft paper or plaster cloth, and finally sprinkle with Huoxiang.