-
The front wheel offset brake is mainly due to the inconsistent pressure of the two oil chambers of the main cylinder or the piston and axle pin of the sub-pump. Rear wheel deflection is a frequent occurrence. Vehicles with ABS generally do not exhibit deflection braking.
What exactly is the offset brake? [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】
-
Hello, the front wheel bias brake is generally caused by the bad brake cylinder, it is recommended that you replace the brake cylinder. [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】
-
Offset brakes are generally brake discs and are worn. caused. It is recommended that you sharpen the brake disc first. It should be OK [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】
-
Hello, the front brake pad is generally caused by the brake cylinder not returning, it is recommended that you go to the repair shop to check to see which brake cylinder does not return [There is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】
-
Replace the brake oil to exhaust the air, do maintenance on the front wheels, and replace the brake calipers [If the car has a problem, ask the car master. 4S shop professional technician, 10 minutes to solve. 】
-
Hello, the front wheel is stupid brake is caused by the brake cylinder is not good, it is recommended that you go to the repair shop to check it. [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】
-
What kind of car is hello? If it is a car, you have to replace the brake cylinder, and it cannot be adjusted [If there is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】
-
What model? [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】
-
Hello owner, disassemble and install the brake cylinder, remove the return pin to check whether it is deformed or stuck, lubricate or replace and repair. I hope mine is helpful to you, and if you still have questions, feel free to ask me. Have a nice ride
Related questionsWhat's going on with the abnormal sound of the front wheels of the car, what is the abnormal sound o8 answers2024-03-03If it is a new car, the new car disc and disc are in a run-in state, which leads to a variety of reasons for abnormal brake noise, rust in water, stones stuck in the middle of the disc and disc, and large metal particles in the brake pad. It doesn't matter as long as it doesn't affect the performance of the brakes.
11 answers2024-03-03The method of replacing the brake fluid is: 1. Turn off the vehicle, open the engine compartment cover, use a syringe to pump out the oil in the oil storage tank, and pump it to the bottom of the tank; 2. Fill the oil pot with new brake fluid; 3. Use a jack to jack up the vehicle, starting from the rear wheel, and remove the tire; 4. Find the oil drain screw of the brake cylinder and remove the rubber dust cap on it; 5. Use a wrench to loosen the oil drain screw, put the rubber tube on it, and connect the other end to the oil drain bottle; 6. Go to the car and start to step on the brakes, if you find that the rubber pipe is discharged from the shallow new oil, the oil change of this wheel has been completed, stop stepping on the brakes, install the tires, and repeat the operation for the next three tires; 7. After all four wheels are discharged, observe whether the oil volume of the oil storage tank in the engine compartment has reached the lower limit, and if it reaches the end, new brake oil can be added appropriately.
11 answers2024-03-03The car is equipped with three rearview mirrors, namely the left side mirror, the right side side mirror, and the ** rearview mirror. The driver's seat must first be adjusted to the most comfortable driving position, and then the mirrors can be adjusted. Adjustment of the left side mirror: >>>More
13 answers2024-03-03Brother, I can understand your current mood very well, very painful, very guilty, and self-blame, I can see that you are a very emotional person, I don't know how far she has progressed with the man, if you are not very close, then you go to redeem, otherwise you don't have the heart to study, you can go to her and tell her how you feel, if she loves you will turn back, in fact, I don't approve of you to redeem, but your current state can only do this, remember to redeem if it's useless, don't entangle, delete everything about her, don't pay attention, You'll never be able to walk that way
11 answers2024-03-031.Pull line:
Tighten the service nut on the brake lever to the tightest (turn clockwise all the way) and prepare to pull the cord. Thread the thread first and pre-tighten it on the fixing screws. Then leave a 5mm gap between the brake pad and the rim and lock the fastening screws. >>>More