How long does it take for central heating to heat up floor heating, and how long does it take for a

Mul. Underfloor heating generally warms up within 3 days. If the new home is heated for the first time, the warming rate is relatively slow, and the warming process only takes a few days to reach the normal temperature.

In the beginning, the temperature should increase gradually. The water temperature on the first day was 18 degrees. The water temperature for the next two days is 25 degrees.

By the third day, the water temperature can reach 30 degrees. Finally, the water temperature rises to a normal value, i.e. 45 degrees, at which point the surface temperature is 28 to 30 degrees. The first use is not to speed up the temperature of the water too quickly, otherwise the floor is prone to cracking and twisting.

It is also necessary to do this if it is used for the first time in winter. In use, it is necessary to humidify the interior to prevent the floor from cracking and deforming. If it is normally open, when the room temperature is 5 degrees, and if the floor decoration is tiled, the thermal effect will be noticeably felt for about an hour; If it is a solid wood floor decoration, then it is slower and takes an hour of heat.

This is hard to say because there are many reasons that affect the speed of the heat source, the thickness of the backfill layer, the thickness of the external wall insulation, the spacing of the pipes, the length of the pipes, and so on.

If reasonable, generally around 10 hours.

Floor heating belongs to the radiation of floor heating, and it takes a day and a half or two days! After the construction of the heating coil and distributor, a hydrostatic test is required. The test pressure is not less than, after one hour of stabilization, the pressure is made up to the specified pressure test value, and the pressure is reduced within 15 minutes.

Generally, the fastest is 2 hours, and the slowest is about 10 hours.

2-4 hours. When the floor heating has just started to heat, it generally takes about two to four hours to heat up in the house, and how long it takes depends on the area of the house, the insulation of the house, etc. The heating temperature of floor heating generally rises slowly, and when the temperature reaches the heating temperature set by the user, the floor heating will not continue to heat up.

Precautions for the use of floor heating.

The first time you use underfloor heating, you should pay attention to the slow heating up. Since it is not guaranteed that the cement and other floors do not contain water vapor, in order to avoid the deformation of the floor caused by the moisture after the temperature rises, the heating of the floor heating should be moderately controlled, so that the ground can be dried step by step until the design water supply temperature is reached. After that, you don't have to worry too much about using it, you can do it in one step.

It should be noted that the surface temperature of the floor heating should not exceed 30, and the temperature of the water pipe should not exceed 60, if it exceeds this temperature, it will affect the service life and service life of the floor. In the average family, the room temperature reaches about 22 in winter, which is already very comfortable, and the normal heating will not affect the use of the geothermal floor.

The above content refers to People's Daily Online - Classification of home heating methods? What are the precautions for home heating?

There is a temperature on the ground two hours after the heating bolt starts, and the indoor temperature reaches more than 16 degrees Celsius after one day, and the overall normal temperature reaches more than 20 degrees Celsius two days later.

Floor heating is also a new type of heating method that has begun to emerge in China in recent years in the north of the Yellow River, and its application has been quite wide in Shandong, Tianjin, Northeast, Inner Mongolia, Hebei and other places in China. In Tianjin, for example, floor heating already accounts for 40% of new buildings, which is widely welcomed by residents.

China** has listed floor heating as a key building energy-saving technology for the promotion and application. From the perspective of development prospects, more than 60% of the future residential heating will take floor heating, and the application prospects are gratifying, and there is a huge development market.

It mainly depends on what you use as a heat source, but also depends on whether the room is heated for the first year or has been heated for several years, if it is a wall-mounted boiler, you start to have a temperature in the house a few hours after you start the furnace, but it takes one or two days to warm the room, if it is the first time to heat, it may take longer, you must know that everything in the house absorbs heat, even the damn air absorbs heat.

If it is urban central heating, if it is 24 hours of heating, it may take 1 day to reach the room temperature of about 20 degrees, and if it is intermittent heating, it may take 2 days to reach this temperature, which refers to the non-first-time heating room. Because the room where the first heat is heated still has problems such as high humidity in the home. The above is a personal experience and is for reference only.

Electric heating for 1 to 1 and a half hours, water heating for 2 to 2 and a half hours, at least.

It takes about 1 day for central heating to heat up at home. Usually after the heating is turned on, the heating process is slow, if you want the room temperature to reach 5 degrees, the heating time is 3-4 hours, and if you want the room temperature to reach about 18 degrees, the heating time is up to 16-24 hours. In addition, when using floor heating for the first time, do not set the water temperature too high at once, which will not only damage the floor heating pipe fittings, but also cause distortion and damage to the floor.

PrecautionsFirst of all, when using floor heating for the first time, it is necessary to pass in 25-30 degrees first, open the valve, let the return water enter the heating pipe, run for a week, raise the temperature by 5-10 degrees every week, until the water temperature reaches about 65 degrees before it can be used normally, and adjust the room temperature according to the outdoor temperature. At the same time, it is also necessary to check the normal functioning of the underfloor heating system.

Secondly, if the floor heating is qualified when the house is inspected, but if it is damaged during the decoration, it will still affect the use of floor heating. Therefore, before using floor heating for the first time, the pipe should be tested to ensure that it does not run water, leak water and leak water.

The first time you use geothermal heating, 3 or 4 hours of underfloor heating can be heated, and you should pay attention to the slow heating.

If the floor heating is turned on normally for 3-4 hours, then it can reach the set temperature, even if the indoor is more humid, it only takes half a day to reach the set temperature. The annual use time of underfloor heating is about four months, and there will be a water divider in different rooms.

Valves that control each area. The temperature in the area can be adjusted on each water supply valve.

1. Understand the repair report of the heating unit, and facilitate contact in case of heating problems;

2. Before the heating starts, the user should first check the payment, whether the heating bolt opening notice is consistent with the payment, and correct the error immediately to avoid misunderstanding;

3. The user should conduct a comprehensive inspection of his own radiators, pipes and valves, and notify the heating company for maintenance in time if he finds that the phenomenon of running, rising, dripping and leaking;

4. When the room temperature is not up to standard, notify the heating unit in time to repair, measure the temperature, and find the reason, and should not take the initiative to carry out maintenance;

5. When there is no one at home, you should inform your neighbors or heating company of your contact person and contact, and you can contact them in case of an emergency and take measures to reduce unnecessary losses.

In addition, in the first year of heating, pay attention to whether your own pipes are leaking, whether the water pressure is enough, if it is collective heating, generally test the water, and find a property if there is a problem. Pay attention to wrapping the pipes exposed outdoors for home heating to prevent the water pipes from freezing and bursting due to low temperatures at night.

When the floor heating has just begun, it generally takes about 2-4 hours for the house to heat up, and the specific time to decide how long it takes depends on the area of the house and the insulation of the house.

If the room is relatively humid, it can take about half a day to reach the set temperature. The underfloor heating lasts about four months a year, and water separators are installed in each room to control the valves in each area, and the temperature in this area can be adjusted on each water supply valve.

Before using floor heating, you should check in detail whether the various connection parts of the floor heating are firmly connected, whether there is water leakage, and only after confirming that there is no problem, can you start to turn on the floor heating. During the use of underfloor heating, the pressure gauge of underfloor heating should be observed at all times.

Numerical values, thermometers.

If an abnormality is found, it needs to be detected and handled.

How to choose the best underfloor heating.

1. Before choosing floor heating, you need to look at the brand and reputation of the floor heating company, try to cooperate with large companies, and give better floor heating quality and better after-sales service. After all, the complexity of floor heating installation is relatively high, and it needs to be installed by professionals to reduce the potential safety hazards.

2. Whether the floor heating can play the best heating effect depends not only on the quality of the floor heating, but also on the technology of the construction personnel, and whether it can ensure the correct installation of the floor heating pipeline. Generally speaking, floor heating needs to determine the specific installation area according to the indoor layout and the orientation of the house.

3. The quality of floor heating pipes should also be selected with special care. Because the floor heating pipe is to be buried in the ground, if there is a problem with the quality of the pipe, it will not be used for a long time to be prone to water leakage, and the maintenance is a big project, and the cost of money and manpower is very large.

4. When choosing a floor heating pipe, you can't just look at its brand, but also look at the quality and environmental performance. A good underfloor heating pipe has a smooth and uniform inner and outer wall, does not produce bubbles, and the flexibility of the underfloor heating pipe.

It should also be good, and there is a relevant qualified test report.