Should a novice learn to drive first step on the clutch, then gear up, and then send the handbrake?

The starting order can be like this.

Novice learning starting skills:

1. Insert the key into the ignition lock, turn on the ignition switch, and then observe whether the instruments are working normally and start the engine. If the instrument is not working properly, the engine should be turned off immediately, and the engine can be restarted only after checking and eliminating the fault.

2. Step on the clutch pedal and put the gear lever into 1st gear.

3. Turn on the left (right) turn signal, honk the horn, and observe the front, left and right, above and rearview mirrors of the vehicle at the same time to see if there is any obstacle to the start, especially pay attention to safety.

4. Relax the parking brake lever (commonly known as "hand brake") and hold the steering wheel (commonly known as "steering wheel").

5. Lift the clutch pedal (this is the key to a smooth start). The essentials are: first lift the clutch quickly until the engine sound becomes lower (at this time the pressure plate and the driven disc begin to rub), release the clutch pedal to slow down, and when the body shakes slightly (the clutch is in the associated movement), pause the clutch pedal slightly, and at the same time refuel a little, and then slowly lift the clutch pedal.

When starting, set the transmission shift in neutral position and tighten the handbrake. Place the front half of your right foot (ball of foot) on the accelerator pedal, use your heel as a fulcrum, and step down and relax with the flexion and extension of your foot joints. Start the engine first, pay attention to whether the engine is running normally and whether there is any abnormal noise.

After the engine is running normally, observe whether there are obstacles around; Steady the accelerator pedal with your right foot while pressing the clutch pedal all the way to the end with the front half of your left foot (the ball of your foot); With your right hand, press and hold the handbrake and hold the lock button forward. Look ahead, hold the steering wheel with your left hand, shift the gear in first gear (starting gear) with your right hand, and hold the steering wheel with your right hand and left hand. Slowly lift your left foot and release the clutch pedal, while pressing the accelerator down with your right foot (when you release the clutch pedal, the accelerator pedal feels like it is pushing up); Until the car runs forward, place your left foot on the lower left side of the clutch pedal.

Step on the clutch first.

In fact, the correct shift posture of manual transmission models is: first release the throttle and then step on the clutch, step on the clutch to the end of the gear and then start with the accelerator, after the vehicle starts driving, continue to lightly step on the accelerator, when the speed reaches 2000 rpm, you will hear "whirring......At this time, it is necessary to change gears, otherwise the speed does not match the gear and easily cause stalling.

For proficient driving skills, loosening the throttle Pedal Clutch Shift Loosen Clutch The process of stepping on the throttle should be done in one go. However, if you still don't step on the clutch to shift gears at higher speeds, you can change gears when you can't get up to speed, so that stepping on the clutch at high speeds will burn the clutch plates for a long time.

If you don't step on the clutch first and then put it in gear, you can't hang it up. If it is forcibly operated, no one can do anything, and it will damage the gearbox and shift switch, resulting in a series of problems such as a decrease in engine power and an increase in fuel consumption. Regardless of the addition or subtraction, the formal procedure is:

Release the throttle, step on the clutch, shift gears, lift the clutch slowly, and lightly fuel at the same time. Remember that the clutch must be stepped low when changing gears, so that the shift can be more thorough.

Precautions for driving:

When driving, you need to pay attention to the distance between the front and rear vehicles, if the distance between the vehicles is relatively small, when there is an emergency, if the distance between the vehicles is relatively small, there will be rear-end collisions and other phenomena, if the distance between the vehicles is relatively large, you can prevent rear-end collisions and other phenomena.

When driving on the road, you need to pay attention to the distance from the front and rear vehicles, so that the car keeps a safe distance, provides time to react when emergencies occur, and needs to adjust your own psychological quality when driving.

It helps the driver to react in time, and the use of high beams helps the driver to observe the state of the vehicle in front of him, and it is best not to drive too fast when driving on the road. When driving, it is necessary to pay attention to reasonable control of vehicle speed and flexible and appropriate use of car lights.

Let's talk about my experience in subject 3 before.

1. Go around the car.

2. After getting into the car, adjust the seat, fasten the seat belt, confirm the instrument situation on the car (the pilot will also confirm before the passenger plane takes off), sound the whistle, signal the start, (pay attention to the use of turn signals) step on the clutch, hang the gear, properly refuel the throttle to reach the appropriate speed, release the throttle and step on the clutch to increase the shift [the increase can only come one level at a time, and the lower gear can be skipped].

3. Step by step until the fifth gear, if you take the third subject, it is best to reach 60 kilometers per hour in the case of good walking.

Of course, you must step on the clutch first before you can put on the gear, otherwise you can try it if you don't believe that the direct gear will click.

You must step on the clutch to be able to hang the gear, otherwise the gear will not be able to hang

Manual transmission: press the clutch, brake, shift, release the brake, release the brake, lift the clutch, start. Automatic:

Step on the brakes, release the brakes first or put the gear first, let go of the brakes to start. Keep in mind that it's a good idea to make sure one of the handbrakes and brakes is running before the vehicle starts to swing, as it's often difficult to tell if there's a ramp in the cab when you're actually driving, which prevents the vehicle from sliding back and forth. The correct step is to start the car first, then press the clutch, put in first gear, and release the clutch from the vertical bucket to start.

Pay attention to the following points when operating a manual transmission car:1. Proficient in stepping on the clutch, practice more, and play steadily.

Develop a good habit and release it slowly at the end. 2.Match throttle and clutch.

When the engine revs at around 2000 rpm, reduce the throttle first and then press the clutch so that the clutch does not forcibly disengage and then shift. The shift order must be 1st - 2nd - 3rd - 4th - 5th. Skipping rope is not recommended.

The order of downshifts depends on the speed of the vehicle. Depending on your vehicle, if the engine speed is below about 1500 rpm, you generally need to downshift.

4.During driving, the vehicle should change gears frequently and choose the appropriate gear according to the speed and road conditions. If you don't change gears frequently, it is easy to cause the vehicle to stall or the engine to go crazy, which will increase the wear and tear of the vehicle and fuel consumption, so you should develop the habit of changing gears frequently.

5.The gear shift action should be coherent, and the clutch should be kicked to the end, in one step. You should be familiar with the gears and practice the feel.

If you can't change gears, put the clutch breaker into the air and release it, then put down the clutch to shift. If the gear is not in place, do not release the clutch, as this will easily wear out the gearbox gear.

Yes, first gear and then release the handbrake.

The main reason for this is safety, after all, the transmission route of the transmission is connected when the gear is engaged. When the gearbox is in first gear, the torque is the maximum, and if the brakes are not applied properly, it may suddenly rush out.

Hook into gear but do not let go of the handbrake, all the power output of the engine will be absorbed by the torque converter, so that the temperature of the torque converter rises sharply, and the torque converter will be burned out after a long time, and the clutch friction plate will be in a semi-linkage state after the dual-clutch transmission is hooked into the gear, and the friction plate will be burned out for a long time and semi-linkage, so it needs to start as soon as possible.

Press the clutch first, then put the gear, and then release the handbrake.

When starting an automatic transmission car engine, the gear selector lever must be placed in P or N gear and the hand brake must be tightened or the brake pedal must be pressed. When the car starts, you should first press the brake pedal, release the hand brake after the gear, and then lift the brake pedal smoothly, and then gradually press the accelerator pedal after the car starts slowly.

When the car starts, you should also pay attention to: after the engine starts and before the car starts, do not step on the accelerator pedal; When gearing, do not release the brake pedal; After starting, the accelerator pedal should not be pressed too quickly or too hard, but should be pressed slowly.

The clutch needs to be pressed. The brakes are divided into situations, only the clutch is stepped on the flat road, and the brakes need to be stepped on when the slope is up.

Manual transmission of the car, in the process of shifting the clutch must be stepped on, and to the end, especially now with synchronizer car transmission, it is difficult to change gears without stepping on the clutch.

During normal driving, the engine speed and vehicle speed are high, and in case of conditions, it needs to slow down and need to apply the brakes. In an emergency, when the brakes are applied, the engine will not be pressed when the engine is about to turn off. The traction of the engine itself has a slowing effect when the car needs to slow down.

Especially when going down a long slope, the reason why you can't drive in neutral gear is to use the traction force of the air call machine to slow down.

After stepping on the brakes, the vehicle deceleration has achieved the purpose, the danger has been eliminated, the vehicle speed has been very low, at this time, the clutch must be depressed, otherwise, the engine will stall, so that the drive train, gearbox, rear axle and engine are damaged.