Tire Care Wheel Cleaning Steps?

The steps of tire maintenance and wheel hub cleaning are as follows: 1. The dirtiest part of the general car is the tires, steel rims and other places, and cleaning these places is an important key to the whole car looking clean. Since these areas are often whole layers of dirt, many people use a very hard brush to get it all at once, and the result is usually more than worth the cost, today I will tell you how to clean this part correctly and quickly.

2. When washing tires, a brush with a long handle is usually prepared so that it can be washed and dried deeply. When washing the front wheels, turning the steering wheel from side to side makes it easier to wash all the places. If the tires are not too dirty, you can wash them with a general detergent instead of spending money on a special detergent.

Unless there's really too much dirt, it might cost a little money.

3. In addition, washing tires can not only be washed with a brush, of course, the brush should be used, but it cannot be used in the chrome mirror treated rim, which will leave obvious scars. The general rule is to use a sponge when washing large parts, and use a brush to wash small areas. For example:

Both sides of the tire can be brushed vigorously with a brush. As for some of the less obvious places, such as: the underside of the fuel tank, the exhaust pipe, etc.

Because it is not obvious, it is easy to be overlooked. When washing, you can use detergent with a brush to brush vigorously.

4. The exhaust pipe can be washed with a sponge, and there is no need to use a brush. In the exterior of the car, as long as this part (tires and below the knee) is cleaned, even if there are some small stains on other parts, the whole car still looks bright. On the contrary, it is not so good.

So don't think that this part is not important, this part is the focus of the whole car cleaning.

5. Note that the tools used to wash these parts are best not to wash other parts.

First of all, when cleaning tires, it is usually necessary to prepare a brush with a relatively long handle, which can be cleaned deeply, if our tires are not very dirty, a little scrubbing can be scrubbed clean, and there is no need to buy a special detergent, just use a general detergent cleaning liquid.

Cleaning the wheel hub is more strict, you need to be extra careful, because the surface of the hub is made of a specific process, and there is a metal protective film that protects the aluminum alloy from corrosion on the aluminum alloy wheel, if it is still washed with a stiff brush, it will destroy this layer of protective film, and even damage the surface process of the hub, leaving scratches on the surface of the hub, which affects the appearance of the hub.

Precautions. When using a brush to clean the wheel, you must choose a soft brush to avoid leaving scratches on the surface of the wheel, which will affect the appearance of the wheel.

1. As long as the general stolen goods are sprayed on the wheel hub with a special cleaning agent, you can use a toothbrush or a special hub cleaning brush for careful scrubbing, and then rinse it with water;

2. When the wheel hub is stained with tar that is difficult to remove, if the general detergent does not help, you can use a brush to try to remove it, but do not use a hard brush, especially an iron brush, so as not to damage the surface of the wheel hub;

The method steps for cleaning car rims are as follows:

1. Prepare rim brushes, toothbrushes, and detergents first, and then rinse the original tires with clean water to wash off the impurities on them and dry them;

2. Take out the detergent and spray the appropriate amount of detergent evenly at a distance of 10-15cm from the rim, and pay attention to the corners and seams of each corner must be sprayed in place;

3. At this time, take out the horizontal rim brush to wipe the surface rim, and use the vertical brush of the rim to wipe the side and edge of the rim;

4. Finally, use a toothbrush to wipe the gaps between the corners and the places where the rim brush can't be brushed;

5. After brushing the entire rim, let it stand for 3-5 minutes and scrub it with an ordinary soaked towel.

Just flush it with a high-pressure water gun.

It can be washed in a car wash in general.

1.When cleaning tires and keels, you must not use a steel brush to clean them, and if you encounter a particularly dirty part, you can use a brush to clean them.

2.Keel clearing enchantment should not be used first, otherwise it will affect the effect and is not conducive to the removal of dirt 3Because keel cleaner is a non-neutral cleaning liquid, cleaning should be carried out in a cooled keel and well ventilated, in addition to protective measures.

Hope it helps you Hope !

Summary. Step 3: Two people follow the process at the same time, spraying sequins evenly on the body from top to bottom.

Step 4: Two people wipe the body with a professional car wash towel at the same time according to the process, and wash while wiping. Step 5:

The two of them used a tornado hand qiang and a towel at the same time to blow water into the zoom gap of the entire car. Step 6: Change the towel at the same time, and cooperate with the tornado hand blowing qiang to wipe the interface of the inner door, trunk, and car fuel tank cap.

Step 7: Two people change special towels at the same time to wipe the interior room and dashboard, and the tornado cleans the air outlet, ashtray and all glass inside and outside the car. Step 8:

At the same time, the two of them changed towels to wipe the inside and outside of the glass, rearview mirrors and front and rear headlights. Step 9: Blow dry the tires, wax (coat) the rim and wipe it clean.

Place a clean foot pad on top. Part 10: Do a good job in the inspection and inspection of the whole vehicle, and formulate delivery and delivery etiquette.

Note: Cleaning the car paint under the spirit:

Hello dear, glad to answer for you! The cleaning and maintenance process of car fine hand hail washing tires and wheels is the first step: spray the steel rim evenly with acid-free detergent and spray the cracks around the door with an all-purpose cleaner.

Step 2: Two people at the same time to retract the mat, put it away, and lay it out. One person rinsed the stains on the body and door edges with high-pressure water, while the other brushed the tires and dried the mats.

Step 3: Two people follow the process at the same time, spraying sequins evenly on the body from top to bottom. Step 4:

At the same time, the two of them wiped the body with a professional and respected car wash towel according to the disturbing process, and washed while wiping. Step 5: The two of them blow water into the zoom gap of the entire car at the same time with a tornado hand qiang and a towel.

Step 6: Change the towel at the same time, and cooperate with the tornado hand blowing qiang to wipe the interface of the inner door, trunk, and car fuel tank cap. Seven steps of the first bright Li paragraph:

At the same time, the two of them changed special towels to wipe the interior and instrument panel, and the tornado cleaned the air outlets, ashtrays and all the glass inside and outside the car. Step 8: Change towels at the same time to wipe the inside and outside of the glass, rearview mirrors and front and rear headlights.

Step 9: Blow dry the tires, wax (coat) the rim and wipe it clean. Place a clean foot pad on top.

Part 10: Do a good job in the inspection and inspection of the whole vehicle, and formulate delivery and delivery etiquette. Note:

Cleaning the car paint under the scorching rimmer:

When it comes to the maintenance of their car, car owners often think of paint and engine first, and the wheel hub is the most easily overlooked. But you must know that the visual impression of the appearance of the wheel is the first, and it is this seemingly inconspicuous place that can properly reveal the owner's taste, so don't ignore the wheel when equipping your car.

Scratch repair of automobile wheels.

Car owners should pay attention to daily cleaning.

When the car is first used, it is necessary to wash the rims diligently, and the wheels should be washed at least once a week when the vehicle is driven every day, first rinsed with clean water, then brushed with a sponge with detergent, and then rinsed with plenty of water. When there are stains on the surface of the wheel hub that are difficult to remove, it is necessary to choose a professional cleaning agent, which can often remove the stain gently and effectively and reduce the damage to the aluminum alloy surface. In addition, there is a protective metal film on the wheel itself, so special care should be taken not to use paints, brighteners or other abrasive materials when cleaning.

Care should also be taken during driving to avoid "hard damage" caused by scratches to the wheel, and once there are scratches or deformations, they should be repaired and repainted as soon as possible.

Maintenance of automobile wheels.

Minor scratches can be repaired on their own.

For car wheels that have already developed scratches, the less minor owners can repair them themselves. We can check the scar first, and if it doesn't hurt the inside of the hub, it can be simply repaired. There are roughly three steps to a patch.

The first step is to clean the hub. We can use a paint thinner to wipe around the scar and remove the dirt. The deepest scratches are difficult to remove, so you can use a toothpick to clean them thoroughly.

When cleaning, it is best to carefully apply adhesive tape around the scar to prevent the unrelated parts from being painted by mistake.

The second step is to tidy up the tip of the brush and apply the retouching paint, which shrinks slightly after drying, and it is best to paint it slightly protruding.

The third step is to allow it to dry completely (about a week) and then apply it with water-resistant paper dipped in soapy water to smooth the surface. The mixture is then used to polish out the shine before waxing.

If you encounter a deep scar, it is important to observe whether the metal surface is exposed, and if you can't see the metal surface, it will not rust, so you can concentrate on applying retouching paint. Dotted on little by little with the tip of the pen and wait for the lacquer to dry completely.

Cleaning of automobile wheels.

Car wheel maintenance tips

Daily maintenance is also essential, when the temperature of the wheel hub is high, it should be allowed to cool naturally before cleaning, and must not be cleaned with cold water; Otherwise, the aluminum alloy wheel hub will be damaged, and even the brake disc will be deformed and the braking effect will be affected. In addition, cleaning the aluminum taijin wheel with detergent at high temperature will cause a chemical reaction on the surface of the hub, lose its luster and affect the appearance. When the wheel hub is stained with tar that is difficult to remove, if the general cleaning agent does not help, you can try to remove it with a brush, but never use a hard brush, especially an iron brush, to avoid damaging the surface of the wheel.

In addition, when the area where the vehicle is located is close to the waterfront, the wheel hub should be cleaned frequently to avoid corrosion of the aluminum surface by salt.

Specific steps: 1. Prepare the above tools, then wash the original tire with clean water, wash off the impurities and dry them.

2. Take out the detergent.

3. Spray an appropriate amount of detergent evenly at 10 15cm away from the hub, and pay attention to spraying the corner seams in place.

4. At this time, take out the horizontal hub brush to wipe the surface hub.

5. Wipe the sides and edges of the hub with the vertical brush of the hub.

6. Finally, use a toothbrush to clean the gaps and the places where the hub cannot be brushed.

7. After brushing the whole hub, leave it for 3 5 minutes, and then scrub it with ordinary wipes.

Wheel cleaning methods include toilet cleaner, all-purpose water, and iron powder remover. Details are as follows:

Toilet Cleaner:

Its main ingredient is hydrochloric acid, which has a strong corrosive effect and needs to be diluted before use. The corrosion of rot socks has a great effect on removing stubborn stains, but it can also damage the coating of the wheel paint, so it is necessary to control the amount and rinse with water after use to avoid residue.

All-purpose water: All-purpose water is also a common household cleaner. Although it is a name, there are many different balances for different stains, and even different brands have different formulas, but it is certain that all-purpose water is a chemical synthesis agent.

Before purchasing, be sure to explain the purpose to the merchant. If you buy the wrong formula of all-purpose water, it is likely that the cleaning ability is poor or the wheel hub is corroded.

Iron powder scavenger:

Iron powder remover is arguably the best of all the cleaning products mentioned above, and it is also the most effective. Because many of the stains splashed on the wheel hub are made of iron powder, iron powder remover can be dissolved well. A few minutes after spraying the remover, rinse it off with clean water and the hub will look brand new.