If you have installed a wireless router at home and want to use TP LINK WR710n to amplify wifi signa

Hello! This can be achieved by setting up dual routing, as follows:

First Route Setting:

1. The router used to connect to the external network is the first router, and we will use this router as the main router. If your router is newly bought and more restored to factory defaults, then its IP should be.

2. Connect to the network with a network cable or wirelessly, it is recommended to use a wired connection;

3. Open a web browser, enter the router login address in the address bar, and press enter to confirm. In the pop-up login box, enter the username admin and password admin,:

4. First of all, set the router to connect to the external network. Click "Network Parameters" on the left, and then select "WAN Port Settings".

5. Select "PPPoe" in "WAN port connection type", enter the correct password, click "Save" at the bottom, save about 10 clocks, and then click "Connect".

6. The DHCP service needs to be enabled on the first router. On the left, select DHCP Server, and then select DHCP Service

7. Set the "DHCP Server" on the right to "Enable".

8. Finally, in order to log in to the router in the future, it is necessary to confirm or change the same network segment as the IP in the router background management IP and the DHCP address pool. Select Network Parameters on the left, and then select LAN Port Settings

9. Set the "IP address" to the IP within the DHCP range you set just now, for example, if the address is different from the DHCP network segment, you need to manually change the IP of the computer to static and the gateway is set to the router IP to log in to the router background when logging in to the router in the future.

10. Restart the router after the setup is complete. If the router does not reboot automatically, you can select "Reboot System" under "System Tools" on the left

Second router setup.

All but the first router need to disable their DHCP function.

1. Similarly, connect the second router with a network cable and log in to the background management interface of the second router. If its IP is.

2. Open the browser, enter the background management IP", and then press the enter key

3. After entering the administrator account and password, click "OK" to open the background management interface;

4. Select "DHCP Server" on the left, and then select "DHCP Service".

5. Set the "DHCP server" on the right to "Do not enable" and restart the router.

Special note: The IP of the two routers cannot be the same.

Set up the router to branch out and then connect to the router and then surf the InternetMethod: Set up a level 2 route.

1. How to connect two routers.

1. There is a cat (modem): cat (modem) - router 1wan port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

2. No modem: network cable --- router 1WAN port; Router 1LAN port --- router 2WAN port; The 2lan port of the router --- the computer.

Second, the setting method.

Before setting, disconnect the WAN port cable of the second router and plug it in after the setting is complete.

1. Set the IP segment of the second router.

2. Set up a second router to access the Internet.

Check the IP details of the computer connected to the first router. (win+r--input, cmd--input:ipconfig all [remember: ip, mask, gateway, dns]).

Set it on the second router, and select Static IP in the Setup Wizard. Enter the IP that the 1st router does not use, and the others: mask, gateway, DNS settings are the same.

Restart your router once it's set up.

3. After restarting the router, the setting is completed, and the line of the 2WAN port of the router is reconnected to make the router 2 network normal.

1. Enter the IP address in the computer browser, the default IP address of the TL-WR710N model is""Then go to the settings interface (the default username and password are "admin") and log in.

2. The next setup is relatively simple, click the setup wizard in the left column to set the wireless username and password. Click "Next".

3. In the interface that appears, you can directly select the default AP mode, select the default AP mode and click "Next".

4. In this interface, it is the place to set the name and password of the wireless, SSID is to search for the name of the wireless display with the mobile phone, and the password can be set by yourself. Select WPA2-PSK encryption and click Next.

5. Then the wireless setting is completed, and the wireless problem is completed as simple as that.

6. You can also directly click on the wireless settings in the left column to set the wireless name and password.

In fact, it's very simple, use router mode, select pp0p dial-up, and then put the account, password into it, mine is the Great Wall broadband, no cat, the network cable is directly plugged in, now the computer, mobile phone with wireless mode can also be on.