I can t turn it on when I turn it on, why can t I turn it on when I turn it on?

This prompt may cause the hard drive to be corrupted. You can use a tool such as "HDTune" to check your hard drive. If you rule out the hard drive, it is likely that there is a problem with the BIOS settings, and you can try to restore the BIOS to the default settings.

There is also a case where the system fails, and if so, generally reinstalling the system can solve the problem.

Summary. Hello dear! Why can't I open the page when I turn it on?

This is due to a network issue or a system failure on your computer. First of all, if it is caused by network problems, do you need to check whether there is any network? Can you first see if the network icon in the lower right corner shows connected?

If there is no connection, there is a problem with network dialing, so you can try to dial again. Secondly, there may be a system failure, then you can use the safe mode to start the computer, if it can start normally, then it is caused by the antivirus software, then you can close the antivirus software to check again; If the page doesn't open properly in safe mode, you can consider reinstalling the system to resolve the issue. Finally, whether it's a network issue or a system failure, take regular backups of your computer to prevent unforeseen data loss.

Why can't I open the page when I turn it on?

Hello dear! Is it a mobile phone or a computer?

Computer. That's how it works.

Hello dear! Why can't you open the page with a smile when you turn it on? This is due to a network issue or a system failure on your computer.

First of all, if it is caused by network problems, do you need to check whether there is any network? Can you first see if the network icon in the lower right corner shows connected? If there is no connection, there is a problem with the rapid leakage of network dialing, and then you can try to dial a new one.

Secondly, there may be a system failure, then you can use the safe mode to start the computer, if it can start normally, then it is caused by the antivirus software, then you can close the antivirus software to check again; If the page doesn't open properly in safe mode, you can consider reinstalling the system to resolve the issue. Finally, whether it's a network issue or a system failure, take regular backups of your computer to prevent unforeseen data loss.

Safe mode is in** yet.

PC Safe Mode can be accessed via the Control Panel. In most operating systems, the Control Panel can be opened via the Start menu or other shortcuts. In the control surface of the lead plate, find the security option, or the system and security option, click in to enter the computer security mode.

I can't open the computer page anymore.

The first step to solve the problem that the computer won't open the page is to check if there is a connection problem. Please check the network connection to make sure that the computer is hungry and connected to the Internet and that the network can be accessed. If the connection is working, check that your web browser version, web page settings, and network** are set up correctly.

Secondly, you can also reinstall the browser, or change the browser to ensure that the browser works properly. In addition, if you find that some pages are working properly and others are not opening properly, check that your computer may be attacked by malware, viruses, Trojans, etc., and remove them in time.

When Emergency Backup mode appears, you can restore it by following the steps below:

1.When entering the "Emergency Backup" mode, select the "Restart" option, restart the phone, and enter the system normally;

2.If you still enter the "Emergency Backup" mode after restarting your phone, you can select the "Data Backup" option, which currently supports NM card, OTG and other devices as storage media for data backup.

Tips: The data types backed up by NM cards, OTGs and other devices include: contacts, messages, call logs, **, **, **, **, memos, recordings, schedules, documents, applications and data, system settings, etc.

and above: Non-provisioned third-party applications cannot back up application data. ）

3.User data backed up to devices such as NM cards and OTGs can be restored on normal Huawei phones through the Backup & Restore app.

4.After the data backup is done, select the "Factory Reset" option to try to restore your phone;

5.If you still cannot enter the normal interface after resetting the factory settings, please bring your purchase voucher to the Huawei Customer Service Center for verification.

Huawei Customer Service Center.

Boarding service. Make an appointment for service.

If the restart fails, it is recommended to restore the factory settings after the backup, if it still can't turn on normally, it is recommended to go to Huawei after-sales service for processing!

1. First of all, we conduct a comprehensive check on the connection between the computer monitor and the host, and plug each connection back to see if there is a connection problem.

2. If the fault still exists, then we need to open the chassis to see if the chassis contains metals and other substances, causing a short circuit in the computer host circuit, and then we smell the computer to see if there is a burning smell, and see if there are damaged components around the motherboard and around the CPU.

3. After checking the whole chassis, there is no abnormality in the chassis, then we will dust the chassis.

4. If it can't be turned on, then use the minimum system method, unplug the data cable of the hard disk, floppy drive, and optical drive, and then check whether the computer can be turned on. Then connect the above devices to the computer one by one, when connecting a certain device, the fault will recur, indicating that the fault is caused by this device, and finally focus on checking this device.

5. If the fault still exists, it is likely to be the fault of the memory card, graphics card, CPU, motherboard, etc., at this time, we only need to plug and unplug these hardware, or replace it again, and try to find the cause one by one.

6. If the memory, graphics card, CPU and other devices are normal, then discharge the BIOS, use the isolation method, place the motherboard outside the chassis, connect the memory, graphics card, CPU, etc. for testing, if the computer can be displayed, then install the motherboard into the chassis for testing until the cause of the fault is found. If the fault persists, you need to return the motherboard to the manufacturer for repair.

What should I do if my computer won't turn on?

I'll answer. Anonymous users

There are many phenomena and reasons why the computer can't be turned on - that is, it can't be started, and the following are a few of the phenomena that I often encounter at work or when helping friends get a machine to illustrate some of my views on this aspect.

1. The computer can turn on the power normally and perform a self-test of the coms, but it just can't start the operating system. The cursor flashes on a black screen with a prompt: "Press any key to restar computer."”

1) The solution to this situation I encountered was to check if there was a floppy disk in the floppy drive. Why do you want to do this?,Because many people's coms settings of the machine start from the floppy disk first,And the floppy disk in the drive is just because of a moment of negligence during work and forgot to take out the working data disk,Not the system boot disk,The system boot file can't be found when the system starts,Of course, it can't be started.。 Several times my friends hurriedly called ** to invite me to go, but it was just this little "problem" that was causing trouble.

2) Another situation is that you have been infected with the boot type virus. When you check that the COMS settings are correct and that the other devices are working properly, you should think about whether the machine is poisoned. The solution, of course, is antivirus, and some rookies asked:

The machine can't start, how can it be disinfected? Why not, boot the "Boot First Drive" setting from the CD-ROM in COMS, save the settings, reboot, stuff the pre-found disc with antivirus software into the CD-ROM drive, and run the antivirus program to kill. The general poisoning files are , , etc.

Restart the computer, does the computer boot up normally? I've been in this situation n times, and it's all done like this.

2. There is some time (more than half an hour) without using the computer, the computer will automatically restart when it starts up, sometimes it will be restarted many times in a row, and then you can log in normally, then the system will prompt that you have just recovered from a serious error. After that, the computer was able to work normally, even for hours on end, without errors. And at this point, if you restart again (or even restart after shutting down), it is completely normal.

The same goes for reinstalling the system.

This problem is relatively big, and it is generally not software.

Reboot and select proper boot device or insert boot media in select boot should be due to the boot sequence being tampered with in the CMOS, which becomes a disc boot, and it cannot be automatically changed back to hard disk boot when the disc drive is not available.

Try if you can use other hotkeys to enter the BIOS, such as F2, if you can get in, you can manually modify the boot order, if you can't get in, it will be very troublesome, it is very likely that the motherboard has been invaded by a virus.

Of course, if you don't rule out the fault caused by other channels, you can try to change the optical drive.

Another: There is a problem with the boot part of your system, which means: reboot, then select the boot disk, or insert the bootable disk into the boot device of your choice.

Check whether the hard disk boot is set in CMOS, if it is, it is likely that there is a problem with the hard disk, check it after booting with the CD.

There are two main categories of BIOS: Award BIOS and AMI BIOS

1. Award BIOS settings the hard disk to boot.

After entering the BIOS, use the arrow keys to select Advance BIOS Features, then press Enter to enter the menu, use the arrow keys to select First Boot Device, click Enter to enter, use the arrow keys to select HDD-0, and then press F10 to save and exit. The boot mode was changed to hard disk boot. Everything!

2. AMI BIOS settings the hard disk to boot.

Go to BIOS, use the arrow keys to select Boot, select a Boot Device Priority, select 1st Boot Device in the submenu, and change this item to the corresponding hard disk.

If it is a vivo mobile phone, it is recommended to use the original charger and data cable to charge for 20 minutes, and press and hold [Volume Down + Power Button] for 30 seconds to try to turn on (in earlier models, press and hold the power button for 30 seconds to try to turn on). If the above operation cannot be turned on, please bring your mobile phone, charger and data cable to the customer service center for processing. The address and detailed information of the customer service center can be found on the official website of vivo on the web version -- Service -- Service outlets, and select your province or city for inquiry.

This is a sign that the host is not starting, you can try it as follows.

1. You can clear the COMS, power down the CMOS to restore it to factory mode, power it on to see if the motherboard can start, and it is OK to start.

2. If it still doesn't work after doing the above, in the state of power off, remove the hard disk, optical drive connection, disassemble the memory, clean the memory and graphics card with an eraser, and then install the memory and graphics card back on the motherboard, power on to see if the CPU fan rotates, such as rotating, in the case of rotation, connect the hard disk first in the case of power failure, and see if the machine can start normally in the home appliance to see if the machine can start normally, if the optical drive is connected after the normal power failure, it is OK.

I don't see the picture.,You press f1,See if you can enter the system.,If you can get in,That's the battery in the computer is dead.,Change one.。

Added: This is your default first boot item is not the hard disk, but boots from the network.

You'll need to go to the BIOS and change the first boot item to a hard drive, so that's it.

I didn't see the picture.,Press f8.,Click on the last correct configuration.,Try! If it doesn't work, press F1!

Don't you see a picture? It can't be that my internet speed is slow.