What if one cat and two computers form a LAN network at the lowest cost? 20

1. If you use XP, you can use the Internet to share it continuously.

If you need 2 computers in a LAN, you can buy a small switch or hub (35 yuan).

Method: 1, ADSL's cat and 2 computers are connected to the switch or hub.

2. Open the network connection on the computer that has established a dial-up connection, and then select the first item of the Internet connection sharing in the advanced options in the properties of the broadband connection (the other 2 options are selected as needed), OK (may need to be restarted), and the other computer only needs to set the IP acquisition method to automatic.

Second, the easiest and most convenient way is to spend between 60-80 to buy an ADSL router, according to the manual settings can be set up to access the Internet.

When installing ADSL, the free modem comes with a routing function, so you don't need to buy a router. But you need to buy a hub (hub), about 40 yuan, connect the network cable split out by the modem to any one of the hub ports 1-4, and the network cables of the two machines are also connected to any one of the 1-4 ports after jumping. Turn on the routing function of the modem and configure the route in IE.

Different routing IP addresses are different, my km300a is.

One is a server, and you can add a network card.

You can use a router or hub!

Nowadays, ADSL can be set up with a local area network.

Buying a router will do the trick.

No, thank you, at least a switch, or a wire, and don't "cross wires" at all

**Line into the cat out of the line into the routing LAN port, connect both computers with the line to the WAN port of the route, and form a LAN.

If both computers are wireless, connect one computer to the router with a cable and set the wireless routing switch to on.

Then use a wireless network card to connect the wireless router.

If you don't understand anything, you can watch the tutorial here, **Tutorial, guaranteed to teach you.

Don't forget to give points!

Are you sure both computers have wireless cards??? Can a wireless router ping your cat? Limited cats? Can it be connected to a wireless router?

It's not complicated, first log in to the routing webpage to set up an automatic dial-up connection (you can read the routing manual if you don't understand it in detail), LAN interoperability, first confirm under the same workgroup, right-click my computer properties, under the computer name, the same workgroup on the line, and then share with each other through online neighbors and so on, there is no problem.

Connect the wireless router to the cat computer to the router, and then make some configuration for the router, and read the manual yourself It's OK very simple.

No need to set up, the cat is connected to the router below, and then the router is connected to the computer under the router. The line of the cat is plugged into the WAN port of the router, and the LAN port of the router is plugged into the computer. Then the computer enters the router address, usually or.

After entering, you can set your account password and you're good to go.

That's so troublesome, two computers are connected to the switch at the same time, one of the computers directly opens the sharing in the attributes of the broadband connection, and allows other network users to connect through the Internet connection of this computer to check the check, and then select a local connection on the OK, and the other can be free.

Okay, that's how our bedroom is, you don't need to set it up, just connect it.

But you should note that the general route can only connect to four computers.

It can be connected like this:

Cat (not used for community broadband) Router network cable LIN port One network cable for each of the four machines to the cat There is a manual for the cat how to let the four machines access the Internet. I won't talk about it here.

Let's talk about LAN settings mainly:

1.Start – Connect to – Show all connections, turn on the network connection.

2.To set up a home or small office network, open the Network Setup Wizard.

3.Next, if it's a laptop, and possibly a wireless card, check "Ignore disconnected network hardware" below.

4.Next, check "This computer connects to the Internet through a gateway in a residential area or another computer on the network", and then give the computer a description or name.

5.Next, the name of the working group. Enter workgroup. on only one machineSeveral other machines joined the working group.

6.Next, check "Enable File and Printer Sharing".

7.Next, next, complete the wizard.

8.The next step – Done.

Open "Local Connection Properties" - Install "-Protocol" and add.

9.If you're just using a LAN to share files. You can skip this one. This is LAN on. This step is more cumbersome. You can play online games on a LAN computer. For example, Red Alert, Warcraft and other single-player games.

Here's how. Open "Local Connection Properties" - Install "-Protocol" and add. Check "IPX SPX NetBIOS" and install it. This step is more cumbersome.

Replace the internal network number for each computer. How to fix it? The default for each machine is 00000000

In the Local Connection Properties General tab, click nwlink ipx spx netbios compatible transporreplacement. Don't make four machines the same.

The first 00000001 the second 00000002 the third 00000003 the fourth 00000004.

10.Add the files you want to share.

1) Right-click the folder in "My Computer" (it cannot be a separate file) and select "Share & Security".

11.Under the "Sharing" tab, check "Share this folder on the network" under "Network sharing and security".

12.Okay, you can now access shared files from other machines through your network neighbors.

Hehe, that's your case.

1.You need to have a wireless router first. Because you are a notebook, your notebook also needs to have a wireless network card so that you don't need a wired connection.

2.When building a home network, you have to have a host.

3.If you want 4 machines to start at the same time, connect this host.

Start again and you're ready to go.

1.A machine (machine A) dials and sets the local connection IP address to be checked on the Advanced tab of the ADSL dialing window of that machine"Allow other network users to connect through this computer's Internet connection"

3.As long as the A machine dials, other computers can go directly without dialing. And each machine can access each other.

You're in the dormitory, right, haha, we're too, the last time I called the boss of the computer city to install the system, he helped us get a local area network, the specific steps are not very remembered, it seems to be to set a number on a machine as a host, and then invite others to join on the line, it's best to find a boss to ask when you go to your computer city next time, and generally won't refuse.

It's very simple, just buy a switch and it's OK, and then your IP needs to be at the same time.

I was dizzy when I saw it, how I didn't know how many bites the cat had taken a few bites.