How to disassemble the Gid washing machine clutch, how to disassemble the washing machine clutch

Tools: a large socket sleeve 38mm (you can borrow it from a car tire repairer), a set of socket wrenches will mainly use 10mm; 14mm also needs a 13mm wrench, and a 4-point molten iron pipe is about 600 800mm; a pipe wrench; A handful of hammers (the bigger, the better).

If it is judged that the deceleration clutch is broken, it is necessary to replace it with a new one. The first thing you need to do is remove the bad deceleration clutch, and here's how to do it:

1) Use a screwdriver to unscrew the fastening screws of the control seat and remove the control seat, at this time, care should be taken not to hardpull the air pressure pipe connected to the water level switch behind the washing machine;

2) Use a screwdriver to unscrew the fastening screws on the fixing ring of the bucket and remove the fixing ring of the bucket;

3) Then use a screwdriver to unscrew down the wave wheel screw, remove the wave wheel, take out the square core gasket under the wave wheel, then you can see the fixed seat under the washing dehydration barrel and the dewatering shaft nut above, and then use a special tool or wrench to unscrew the dehydration shaft nut, and then take out the cushion sleeve on the dehydration shaft of the deceleration clutch, remove and wash the dehydration bucket, and then take out the gasket set on the dehydration shaft (this piece is very important, and the new clutch should be installed back. ）；

4) Dump the washing machine forward, so that it is placed face down, you can see the structure of the lower part of the washing machine, use a sleeve or a small wrench to unscrew the fastening screws on the fixing frame, remove the fixing frame, then remove the V-belt, and then use a sleeve or a small wrench to unscrew the fastening screws of the deceleration clutch on the supporting plate, so that the deceleration clutch can be removed.

P.S. If the dehydration bucket is rusty and cannot be removed, the clutch is broken and no longer needed, the sequence of actions is as follows: do the fourth step first.

Remove the fixing screws of the clutch under the washing machine, and the belt, and then do the third step, after the wave wheel and the nut of the dehydration shaft are unscrewed, directly align the clutch with the hammer and iron shaft, knock him down, must be operated by two people, one person carries the dehydration bucket upward, one person smashes the hammer, and the clutch can be loosened after a while. Install from the bottom up when installing. The sealing surface is clean and generally does not leak.

The order in which the deceleration clutch is changed is reversed from the order in which the deceleration clutch is removed. That is, first fasten the newly replaced deceleration clutch on the supporting plate with fastening screws, then install the V-belt and fixing frame, erect the washing machine, install the gasket on the dehydration shaft of the deceleration clutch, and then install the washing dehydration bucket, pad sleeve, fastening the dehydration shaft nut, install the square core gasket and the wave wheel, and then fasten the wave wheel with the wave wheel screw, and finally install the water bucket fixing ring and control seat.

There is a gong wire in the middle of the wave wheel, cross the new son, remove the wave wheel, you will see the central axis, there is a big gong cap, the special hand is loosened, and then the gong crepe wire below is removed, the whole is taken down, buy a new one, install it, adjust the belt, and it's done.

The screws on the four sides thank you for pulling the ribs and removing them.

1. It is more troublesome to replace the clutch of the automatic washing machine, first unscrew out the screws that fix the noodle frame, and remove the four screws that fix the outer barrel ring to remove the outer barrel ring.

2. Unscrew out the wave wheel screw to take out the wave wheel, and then use a special sleeve to unscrew out the big nut that fixes the inner barrel (the inner barrel of Q818 and Q828 models is fixed with four M6 bolts) and take out the inner barrel of the clutch of the automatic washing machine.

3. Lay a soft cloth on the ground to turn the washing machine on its side, use the sleeve to unscrew out two bolts that fix the protective frame on the clutch of the automatic washing machine, and remove the protective frame.

4. Use the sleeve to unscrew out the four bolts that fix the clutch, take off the belt, and finally take out the clutch of the automatic washing machine and replace it with a new clutch. Then assemble the clutch of the automatic washing machine according to the original steps.

5. The degree of dirtiness of the clothes is judged by the transparency of the water. Add an infrared photoelectric sensor at the drain of the laundry bucket to make the infrared light pass through the water and enter the receiving tube on the other side. If the transparency of the water is low, the light energy obtained by the receiving tube is small, indicating that the clothes are dirty.

Piezoelectric sensors are used for dewatering. When the dewatering bucket rotates at a high level, the water sprayed from the dewatering bucket acts on the piezoelectric sensor, and according to this pressure change, the dewatering operation is automatically stopped.

6. When we inject a certain amount of water into the laundry bucket to make the motor run at low speed, the power is quickly cut off after the Ming Xusui is stable, and the laundry bucket drives the motor to continue to rotate under the action of inertia, at this time, the motor winding produces back electromotive force, and after the half-wave rectification and amplification and shaping, a rectangular pulse series is obtained, and the quality and quantity of clothing can be obtained by analyzing the number of pulses and the width of the pulse.

1. It should be tightly fit and pressed in. Put the oil on the shaft up, fix the flange and tap the motor shaft down with a hammer.

2. The clutch of this structure is more difficult to disassemble and repair, and there is no need to repair the leakage of the sealing ring, which is fixed with the four holes of the flange screw, and it is relatively convenient to disassemble when washing the inner cylinder or disassembling the clutch.

Stand up the washing machine, and vigorously knock the thin shaft of the clutch in the middle of the dehydration bucket, which is the most difficult time to disassemble the clutch, first carefully clean up the surrounding scale and garbage, you can also spray a little rust loosening agent, and then find a suitable wooden stick to resist the thin shaft in the middle of the clutch, and knock the clutch off the laundry bucket with a hammer.

Install the clutch: After the damaged clutch is removed, wipe the hexagonal hole of the dehydration bucket clean, and you can install the new clutch, in the reverse order of the above, do it upside down, carefully put the clutch in place according to the old look, and tighten the screws and nuts. The big nut that fixes the dehydration bucket must be tightened with the clutch, otherwise it is easy to loosen after a short period of use, causing the dehydration bucket to produce serious noise, or the dehydration bucket is unbalanced and hits the balance rod of the washing machine, so that the washing machine can not be dehydrated normally.

This answer is suitable for most washing machine models of Haier EG10014B39GU1 &&& Little Swan TG100V88WMUIADY5 and other brands.

The steps of disassembling and cleaning the inner liner of the Gide washing machine are as follows:

1.Cut off the power supply. Loosen the screws counterclockwise with a screwdriver. Once removed, pick it up with both hands and remove it.

2.After the blade is removed, there are still 4 screws that can be unscrewed with a spare screwdriver, and most of them need to be unscrewed with a wrench.

3.There is one screw on the left and right sides of the Gide washing machine, pry open the casing, unscrew the screws, and there are two more in the back.

4.After unscrewing the four screws on the outside of the upper cover, the upper cover can be lifted.

5.The reason why the cover cannot be removed completely is because there are water pipes and wires connected together, so don't mess with these wires. At this point you will notice that there is a lid on the barrel. Unscrew 4 screws, lift the slag to destroy and change 4 small buttons, and easily remove.

6.If the four screws under the blade are unscrewed in the third step, then the inner barrel is shaken and removed.

7.Remove the inner bucket and you will see the dirtiest outer bucket, rinse it repeatedly until it is clean.

1. Cut off the power supply! The washing machine was removed into place as power and drainage were needed at the back. Loosen the screws counterclockwise with a screwdriver. Once removed, pick it up with both hands and remove it.

2. After the blade is removed, there are 4 screws that can be unscrewed with a stocking acre wire knife, and most of them need to be unscrewed with a wrench. If you have a hex wrench of the same size, it is relatively simple.

3. There is one such screw on the left and right sides of the outside of the washing machine, pry open the shell of the judgment and unscrew the screw. There are two more in the back.

4. After unscrewing the four screws on the outside of the upper cover, the upper cover can be lifted. Be very careful at this time! The lid cannot be removed completely, but can only be turned back. All backs need such support!

5. The reason why the upper cover cannot be completely removed is because there are water pipes and wires connected together, don't mess with these wires, just keep it in this state. At this point you will notice that there is a lid on the barrel. Unscrew 4 screws and lift 4 small buttons for easy removal.

6. If the four screws under the blade are unscrewed in the third step to flush the lead, shake the inner barrel and take it out. We usually see the inner wall of the inner barrel and think it is very clean. In fact, the exterior wall is very dirty and has a bottom!

7. Remove the inner barrel and you will see the dirtiest outer barrel! I've washed it once before, and I'm sure you're many times dirtier than mine when you first opened it! Don't remove the outer barrel, because the drain pipe and power cord connection below are more complicated, we just need to remove it and wash it, don't touch it!

Take water from a bucket and pour it in, then brush with a brush or toothbrush. After brushing, you need to turn on the power and choose dehydration directly, so that the sewage can be discharged and cleaned after repeating several times.