How to set up a wireless router as a wireless switch, and then realize the wireless Internet functio

I set the first-level routing IP to, the address pool from to, and the second-level routing IP to the address pool from the address pool to the wireless router is obviously saturated in the address pool of the wired router, right?

I think the problem is,You open the DHCP function of two routers at the same time,I haven't used this wireless router I'm not sure,I'm familiar with the brand model,When used in this way,It is only possible to open the DHCP server function of the first-level router,The wireless router should be turned off,In this way,All PCs are connected to get the IP address from the first-level router。

I estimate that wirelessly connected computers are unable to access the Internet because they use wireless routers as gateways.

The brother above said well, but the most convenient thing is,You put the modem directly into the wireless router.,The general wireless route also has a wired function.,It's simpler.。

Two scenarios:

In the first case, set up the wireless router as a switch.

First, turn off the DHCP function of the wireless router;

The second step is to set the LAN address of the wireless router to the same address segment as the LAN address of the neighbor router (for example, if the neighbor is a neighbor, then the LAN address of your wireless router should also be set to any of the previous addresses);

Step 3: Set the gateway address of your wireless router to the gateway address of your neighbor's home, if the gateway address of your neighbor's router is, you may want to set the gateway of your wireless router to.

Finally, plug the network cable from your neighbor's house into the LAN port of your wireless router, and you're good to go (you don't need to change the wireless settings).

In the second case, still treat your wireless router as your wireless router, the first step is to plug in your router and press the reset button (there is a small hole in the router) for more than 6 seconds to restore the router to its initial settings.

The second step is to withdraw the network cable from the neighbor into the WAN port of your wireless router, set up your wireless, and you can surf the Internet.

In contrast, the second case is easier to do, I think.

One type of LAN connection, the same network segment, just turn off DHCP.

The other type of WAN connection is set to different network segments.

Let's assume first: your IP address is the IP address of the line, and the address assigned by DHCP is then a suggestion for you: 1. Connect the wireless routing WAN port to the LAN port with the wire, and set the wireless routing WAN port to a fixed IP address for access.

2. Set the IP address of the wireless WAN port to.

3. Set the IP of the wireless LAN to .

4. Turn on the DHCP function of the wireless LAN and set the access key (you can define it yourself) in security

The method of wireless routing as an AP.

The following method was told to me by the 400 girl when I played TP's 400**, and it is said to be suitable for all TP wireless routing.

Method: 1. Enter the route and turn off DHCP (I remember it is in the DHCP server, easy to find).

2. Change the address of the route to the network segment used by your network in the WAN port settings > LAN port settings.

3. Connect the network cable to the LAN port (as long as it is the LAN port).

Here's how to make an AP for the DLINK DI-524M wireless router:

1. Click "Wireless Settings" on the left, and then select the wireless working mode in the wireless working mode, here select the access point

2. Change the wireless network name (also called SSID), select the channel, if you don't want to change it, then this step can be skipped.

3. To change the wireless encryption, it is recommended to select WPA Personal, and then fill in a password of no less than 8 digits.

Personally, it is recommended that the password is set at 11-15 digits, it is not safe to set it too short, and it is very inconvenient to use it in the future if it is too long.

4. Save it, and then wait for it to restart.

5. Change the management address of this route, click "Network Settings" on the left, and fill in the IP you assigned to this AP in the LAN settings, and this.

masks and gateways for the network.

6. Save, then it will automatically restart, remember to connect the network cable to the LAN port (as long as it is the LAN port).

PS: It should be noted that after 524M is made into an AP, the LAN port can be used as a switch.

There is also this model of routing can do WDS AP function, but the effect has not been tried, interested friends can try.

Just plug in the LAN port, and the wireless router can be used as a switch.

It's okay if you don't connect the WAN port, and the rest don't need to be changed.