How to connect the home telecom ADSL router? Urgent!

1. First, connect your computer and router to the network. Connection method, connect the cable from the ADSL cat to the WAN port of your router, and the remaining LAN port can be connected to your computer or switch. 2. Then set your IP address to be, subnet mask, OK all the way, ipconfig (enter in the state of the command prompt) to confirm that your IP address has become.

3. Then open the IE browser, enter it in the address bar and press Enter. The screen prompts you to enter the username and password, fill in the default username and password of the router (the router username and password I use are admin, other routers can refer to the manual) 4. After enterprising, the setup wizard will pop up, if it doesn't pop up, it doesn't matter, click "Setup Wizard" in the navigation blue on the left, and the wizard welcome message appears on the right, click "Next" 5. Select "ADSL Virtual Dialing (PPPoE)" and click Next. 6. Enter the username and password, which are the username and password you use when dialing with ADSL 7. Click "Done" If you are using a monthly subscription, it is recommended that you do the following work next.

If you are timer, it is recommended that you skip directly to the DHCP setting section 8. Click "Network Parameters" - WAN Port Settings in the left navigation blue. 9. Select "Auto-Connect" and click "Save" In this way, the broadband connection part has been set, you can click on the "Running Status" in the left navigation window, and click to check the WAN port status in the right window. If the "Disconnect" button appears (don't click it), the connection is normal. View the original post

The router WAN port is connected to the modem, the LAN port is connected to the host, and then the user name and password are entered into the router settings in the browser, and the assigned virtual dial-up is filled in to connect to the network, and the DNS server IP (two groups) of the ISP will be displayed on the page, and then the host IP (gateway) (and DNS (the two groups just got) are set on the host, OK. Regarding your second question, the host and router are connected to the same network with network cables.

Use the cat's own connection cable,Connect the cat and the router,(Pay attention to the interface of the router,There is an interface that is connected to the cat and the entrance),Then other machines can be connected to the router together,Generally in the browser,Enter or other (see the router's manual)Open the router and fill in your password in the router。 It's OK to restart View the original post

If I don't set up a direct connection at all, can I connect to only one device? I can't connect right now.,But isn't it necessary to play in IE when you're connected to the Internet? If I couldn't connect to it before, how do I go to that routing setting interface?

3.What is the DNS mentioned in the router manual? Also ask the provider, doesn't this set the line?

View the original post

Hello: If you use a router and your mobile phone can also surf the Internet normally, it means that your router settings are correct, the computer connection may not be because the IP address is not set correctly, you can set the IP address to automatic, and the network cable connected to the computer may be broken, you can change a test.

If the mobile phone wireless Internet access is normal, then the router and broadband are fine, see if your computer's local connection is normal, if the local connection is crossed, it means that there is a problem with the network or router port, or your network card is faulty. If the local connection is normal, check what the IP address obtained by the NIC is, it may be bound to the IP, and change it to automatic acquisition.

The computer should be connected to the router, not to the cat.

Do you want to connect your desktop computer through telecom broadband and then connect to a wireless router to set up a home LAN?

Are you going to use a desktop computer with a wireless connection?

Router Setup Tutorial].

Home Network Environment Cabling]:

1. There is a telecom cat: the telecom cat --- router WAN port; The LAN port of the router --- the computer;

2. No telecom cat: network cable --- router WAN port; The LAN port of the router --- the computer;

Computer enters the router]:

1. Check your IP first, method: win+r--- input: cmd--- enter in the black and white interface: ipconfig, press enter;

4. Pop up the router login interface and enter the default login username of the router: admin and password: admin (if it is incorrect, look at the back of the router);

5. The above methods do not work, in the reset router; The address, password, are all on the back of the router;

Set Router Dialing]:

Automatic acquisition of computer IP and DNS settings;

1. Enter the router. In the [Setup Wizard], select [PPOE Dialing] (some are ADSL Dialing), enter your Internet username and password as prompted, and save;

2. In [Network Parameters] --WAN Settings], select [Normal Mode], and select [PPOE Dialing] in the three options of [Connection]. The next is to select [Auto Connect], Save, and Exit;

3. If you want to use wireless wifi, your router must have a wireless routing function, in the settings, turn on the wireless wireless hole by the function, here, the wireless signal signal to change to one of them. The strongest anti-interference. You can also set a password for your Wi-Fi connection.

Dear users, according to the description, pulling broadband, and then sharing the Internet through the wireless router is the common appeal of every consumer;

The method of realizing the letter fiber state is also very simple, and the line connection is completed first, as shown in the following figure

Next, open the browser and enter it to enter the router settings page;

Different router addresses may be different, please refer to the manual for step-by-step operation;

After that, enter the password of the broadband Internet access account;

Hope the above helps!

If you have any other questions, please come to the platform or the official website of Anhua Yuanhui Zhuying Telecom to ask questions;

Hello! The implementation method is also very simple,First complete the line connection of the world stove tremor,Open the browser after searching and defeating,Enter into the router settings page;

Different router addresses may be different, please refer to the manual for step-by-step operation;

Plug the Internet cable into the WAN port of the Infinity Router.

The rest of the computers are changed to the wireless router through the wireless connection, and the computer enters the user name and password in the IE bar one day, and the default is admin

There is a configuration guide hall in the hall, just enter the automatic dialing in it Let the router vibrato be automatically dialed directly, and the rest can be accessed.

It's the same with a limited router.

Connect the WAN uplink port of the router to the cat's hunger Li network port, and then connect your two computers to the network ports on the user side of the router, and you can answer the trembling, and you don't need to connect any broadband. Then you need to log in to the router, configure the WAN uplink port of the router to PPP dial-up mode, set up your broadband account, and then enable the DHCP server function to assign an IP address to your computer. Finally, your computer is set to automatically get an IP, and you can surf the Internet.

Just like the rotten old one above, it should be possible, it's very simple.

TPLink and Dlink say that hunger is rising, and it is clearly written in the book.

I hope you succeed in which Pei.

To give you a **circle Zen, it is tplink, you can refer to configure your route.

Plug in the router and connect one end of the network cable to the WAN port of the router and the other end to the network cable interface of the telecom.

Use one end of the second network cable to connect one of the router's LAN ports 1234, and the other end to the LAN port of the computer.

Open a browser and enter the background management IP of the optical fiber wireless router. This IP can be seen from the panel on the back of the router:

Then enter your username and password and click User Login. The account number and password can also be seen on the back panel of the router: (If you don't have the account number and password, or if you enter it incorrectly, you can reset the router, press the reset button on the router until all the lights on the router are on.) ）

After the password and account number are verified, you will enter the main interface of the router

Click "Network", which is turned on under "WLAN" by default, where you can manage wireless network cable settings, that is, WiFi:

Scroll down to the bottom of the page and click on the "Advanced" button

In the "Advanced" parameter configuration page that opens, you can set commonly used parameters:

Then go back to the back office under "Manage" to change the username and password of the backend management

Why not? The cable that the cat connects to the computer is connected to the router. The computer is pulled out of the router.