How to clean the drain of the refrigerator when it is blocked

1. Ordinary dirty blockage treatment method: a. If the lower part of the drainage pipe is blocked, it will not be very deep, just poke it with a screwdriver or the like; b. If the drainage pipe joint is blocked, the wire of appropriate hardness can be tilted into a certain arc and poked down into the drainage port (the depth should not exceed 50mm). Be careful not to scratch the refrigerated container and drain nozzle until it is cleaned and drained smoothly.

A 4-capillary tube is welded to the pipe at the exhaust end of the compressor to form a tee with the system pipe. The other end of the capillary is sealed by welding, and the capillary is then inserted into the refrigerator drain to reach the ice cube. The length of the capillary depends on the length of the refrigerator drain.

Take a copper pipe with a diameter of 6mm, about 80cm long (from the drainage hole of the actual refrigerator to the outlet), seal one end with a welding torch, vacuum the other end with a pressure gauge, fill it with R12 refrigerant (refrigerant with negative temperature coefficient can be) about 8g, then seal it, and then put the copper pipe at the outlet near the compressor into the drainage hole (using the principle of refrigerant heat and cold conduction, the cold energy is dispersed in the place that is easy to ice blockage).

1. First of all, you need to prepare a thin hose, hot water, a large-capacity syringe and dish soap to solve the problem of how to clean the drain of the refrigerator. 2. You need to connect one end of the hose to the syringe, and the other end into the refrigerator drain hole, and pull out the stagnant water and dirt inside. 3. After the hot water is filled, mix it with dish soap, and then use a syringe to draw hot water into the drainage hole until the water overflows, so that the drainage pipe can be dredged after several times.

4. Use the hose to insert it into the drainage hole until the hose comes out from the other end of the drainage hole. 5. Another is to fold the bottom cover at the back of the refrigerator and find the small hole to clean it. There are several reasons for this:

1. The drainage hole of the refrigerator is very important, it cannot be blocked, and the blockage will cause water accumulation in the refrigerator and affect the normal use of the refrigerator.

2. The drain pipe of the refrigerator needs to be checked regularly, so as not to affect the normal use of the refrigerator because there are too many blockages.

3. If there is too much condensation in the refrigerator, too high moisture will also cause the drainage hole to be blocked due to food mold.

4. If the drain hole of the refrigerator is blocked, whether it is the freezer or the refrigerator, it needs to be dealt with as soon as possible. Otherwise, it will affect the normal refrigeration of the refrigerator.

It is recommended that you can pull out the drain pipe to clean the drain hole directly, or you can contact the refrigerator maintenance personnel for repair.

You can buy a "refrigerator drain hole unclogging" tool online and read the instructions for how to use it.

When the water outlet hole of the refrigerator is blocked, it often causes a large amount of water to accumulate in the refrigerator. To solve this problem, first unclog the clogged water outlet hole in the refrigerator. If you don't know, the water outlet hole of the fridge freezer and the drain hole of the fridge are both on the back.

Tools Ingredients: cotton swabs or chopsticks.

1.In the daily use of the refrigerator, when a large amount of water is often found on the bottom plate of the refrigerator fresh-keeping cabinet, it may be that the refrigerator outlet hole is blocked.

2.At this time, you can use a dry rag to absorb the stagnant water in the refrigerator first, so as not to get water everywhere in the next step.

3.Once the stagnant water has dried, you can find the outlet hole in the refrigerator. Generally, the water outlet hole of the refrigerator is in the crisper above the refrigerator. Open the crisper and you can find it at the back of the middle level inside.

4.As shown in the figure below, open the fresh-keeping cabinet of the refrigerator, and then remove the items in the middle of the fresh-keeping cabinet, and find that there is a water outlet hole behind it, and there is also a water guide tank at the location of the water outlet hole.

5.Wipe the inside of the sink first. If the water outlet is blocked, slowly use a cotton swab or chopsticks to get the blockage out, and then wipe the hole clean, so that the problem of the refrigerator water outlet blockage is solved.

6.The water outlet hole of the refrigerator should be checked frequently to avoid excessive clogging. After drilling under the hole, it will be troublesome to dredge; In addition, in order to reduce the situation that too much condensation and too much water in the refrigerator can cause mold and clog the water outlet hole, it is usually necessary to drain and empty the items with a lot of water before putting them in.

Always have standing water in the fridge? Clogged drain holes? The cleaning method can be learned as soon as you learn it, and you can easily master it in one minute

First of all, find out the root cause of the problem, you can increase the temperature of the refrigerator to eliminate the blockage caused by the accumulation of ice; If the search is caused by the accumulation of ice, it will need to be dredged with a hard wire, or a catheter will be used to blow it up.

Generally speaking, there are two main reasons for the blockage of the drain. The former is that when we use the refrigerator, the temperature is too low for a long time, and the water retained during use condenses into ice, which accumulates in the drainage cavity and pipes, causing blockage. In the latter case, when we store items in the refrigerator, the debris falls and accumulates at the mouth of the drain pipe, causing the pipe to clog.

Once the cause is clear, we can clean the drains ourselves. First of all, we need to determine what caused the blockage of the drainage pipes. When the temperature inside the refrigerator is about the same as the room temperature, if it is due to the blockage caused by the first reason, the drain will naturally be unblocked as the ice melts.

If the pipe is not unblocked at this time, you need to use a wire with a certain hardness to extend along the pipe to dredge the pipe, or you can use a flexible conduit suitable for the size of the drain to blow air on the drain to squeeze out the debris.

Although the refrigerator drain hole is blocked, it is relatively simple to clean, but in fact, as long as we pay a little attention in our daily use, we can avoid this problem.