How to get through the blocked drain hole of the refrigerator, what to do if the drain hole of the r

1. First of all, use pliers to remove the foreign matter in the drainage hole. If the drain hole is blocked by debris, you need to hook the sewer mouth (generally located at the lowest part of the sewer) with a wire, and then pull it up hard to make the debris fall off.

2. If the above methods cannot be solved, then you need to use professional tools to clean up.

3. Buy a special dredging truck in the supermarket to dredge the drainage holes of the refrigerator. Before using the dredging vehicle, it is necessary to check whether there are sharp objects or hard objects in the pipeline that hinder its work, so as to avoid damage; Then insert the dredging truck into the pipe and turn on the switch to rotate, stretch, squeeze and other operations to complete the cleaning task.

1. Ordinary dirty blockage treatment method: a. If the lower part of the drainage pipe is blocked, it will not be very deep, just poke it with a screwdriver or the like; b. If the drainage pipe joint is blocked, the wire of appropriate hardness can be tilted into a certain arc and poked down into the drainage port (the depth should not exceed 50mm). Be careful not to scratch the refrigerated container and drain nozzle until it is cleaned and drained smoothly.

A 4-capillary tube is welded to the pipe at the exhaust end of the compressor to form a tee with the system pipe. The other end of the capillary is sealed by welding, and the capillary is then inserted into the refrigerator drain to reach the ice cube. The length of the capillary depends on the length of the refrigerator drain.

Take a copper pipe with a diameter of 6mm, about 80cm long (from the drainage hole of the actual refrigerator to the outlet), seal one end with a welding torch, vacuum the other end with a pressure gauge, fill it with R12 refrigerant (refrigerant with negative temperature coefficient can be) about 8g, then seal it, and then put the copper pipe at the outlet near the compressor into the drainage hole (using the principle of refrigerant heat and cold conduction, the cold energy is dispersed in the place that is easy to ice blockage).

The refrigerator is one of the most common household appliances in our daily life, if the water outlet hole inside the refrigerator is blocked, then it will cause a large amount of water to be left in the refrigerator, affecting our daily use, so how to get through the refrigerator drainage hole? Let me lead you through this problem.

1. How to get through the blocked drain hole of the refrigerator.

If you usually find that there is a lot of stagnant water on the surface of the refrigerator crisper, it is probably that the water outlet of the refrigerator is blocked.

1. First take a dry rag to clean up all the stagnant water inside the refrigerator, which can facilitate our next step of construction and prevent slurry from being coated everywhere.

2. After the stagnant water is treated, find out the water outlet hole inside the refrigerator, usually the water outlet hole is inside the fresh-keeping cabinet above the refrigerator, open the fresh-keeping cabinet, and you can go to the rear of the middle layer to find it.

3. Remove the items on the fresh-keeping cabinet to find the water outlet, usually there will be a water guide groove behind the water outlet hole.

4. Scrub the inside of the water guide tank, if there is a blockage, we can use cotton swabs or chopsticks to clean up the blockage, and then deal with the inner hole, so that the problem of blockage can be solved.

2. What are the precautions for using the refrigerator?

When you usually use the refrigerator, you should regularly check the water outlet hole, which can prevent too much debris in it, and it is more troublesome to dredge the hole after getting it down.

Note that in order to avoid too much water accumulation in the refrigerator, the moisture is too high, resulting in mold and clogging the water holes, we must dry it before putting it in, which can reduce the probability of clogging.

I conclude: the above is the dredging method of the refrigerator drainage hole blocked, from the above article we can see that if it is found that there is a lot of water inside the refrigerator, then there is a high probability that the drainage hole is blocked, we must dredge it in time, otherwise it will lead to more and more water inside, which will affect the function of the refrigerator, and seriously will cause damage to the refrigerator, I hope it can help you.

Refrigerator drain hole clogged solution:

1. When found on the bottom plate of the refrigerator fresh-keeping cabinet, if water accumulates frequently, it may block the water outlet of the refrigerator;

2. You can use a dry rag to absorb the stagnant water in the refrigerator;

3. Generally speaking, the water outlet of the refrigerator is in the fresh-keeping cabinet on the top of the refrigerator. After the fresh-keeping cabinet is opened, look for it on the inside of the back of the middle layer;

4. There is a water outlet on the back of the fresh-keeping layer, and a water guide device is provided at the position of the water outlet. Figure below;

5. First of all, take out the foreign matter at the entrance of the refrigerator drain hole, and pour a small amount of water into the cup mesh drain hole. Check that the drainage is unblocked. If the drainage is not smooth, it proves that the drainage hole is blocked.

Then use a cotton swab or chopsticks to slowly remove the blockage, and then wipe the hole clean so that the water outlet of the refrigerator is clogged.

1. Open the refrigerator door and find the location of the small hole, if you find a lot of water, it means that the drainage hole is blocked.

2. The location of the drainage hole of each refrigerator is different, use a small toothpick or a small bamboo stick to get through, if the blockage is not very bad, it can generally be opened.

3. If it can't be opened, find a syringe, cut off a section of plastic infusion tube, put the plastic infusion tube on the syringe, insert the hose into the small hole, and suck out the water inside.

4. After sucking the water out, fill up a syringe with water, drive it into the small hole, and try to see if the drainage hole is open.

5. If the water does not overflow, it means that the drainage hole is open, then clean the refrigerator, and wipe the refrigerator after washing.

AnswerFirst of all, prepare a soft water hose syringe and 1 basin of hot water, and insert the soft water hose into the drain hole of the refrigerator; Second, inject hot water from the syringe into the drain hole and repeat several times until the blockage is slowly squeezed out. Finally, if the drain hole is filled with water smoothly, it means that the drain hole has been unblocked.

The tip is to buy a set of syringe dredgers online, which is convenient and fast.

The fridge drain is clogged. You need to find a thin plastic pipe that is a little harder, and poke it down the drain pipe to poke out the dirt and ice inside. The drain pipe will be opened naturally.

The possibility of the drainage hole being blocked by ice is relatively small, generally the flowing water contains impurities, after the water evaporates, the impurities become a membrane-like thing to block the drainage hole, you can use a little hard but can bend things through, such as soft wires, wicker, etc. When buying a refrigerator, it is usually equipped with a drain hole, but it is too short to use.

The ordinary blockage of the refrigerator drain hole means that the inside of the drain hole or the mouth of the drain hole is blocked due to the entry of debris into the drain hole of our refrigerator.

We start by cleaning out most of the objects inside the refrigerator. The key point here is to expose the position of the drainage hole, so that we can have the corresponding operation space, so that it is convenient for us to carry out the dredging operation of the drainage hole.

The usual thing is to clean things like the drain holes around the refrigerator.

Use wire for unclogging. In other words, if we find a lot of water at the mouth of the drain hole after we expose it, it means that the inside of the hole is blocked.

At this time, we can directly use the wire to dredge. It is to use a thin wire to dredge slowly inward along the drainage hole, so that the debris inside can be stirred, and then it can be cleaned out along the drainage hole. It's also the easiest way to unblock.

Use a blowing machine to unclog it. For example, our most common pump is red or some of the other blowing machines.

We also find the drain hole, or insert the discarded pipe into the drain hole, and then pump it inside. At this time, the pressure and fluidity of the gas are generally used, and some items blocked inside the drainage hole can also be cleaned out. Moreover, this cleaning method will not cause damage to the inside of the hole before the exclusion, so it is safer and more reliable, but the requirements for tools are relatively high.

Purchase a dedicated unclogging tool for unclogging. For the drainage hole of the refrigerator, because the hole diameter is relatively small, we can find some special dredging tools to dredge it directly.

We can buy special dredging tools here, and then dredge them at the location of the drainage holes according to their use requirements. Basically, it's all achievable.