How to install the louvers after the air conditioning fan is dismantled and washed

Before installing the air-conditioning shutters, the air-conditioning blinds should be transported to the installation place according to the identification number and placed on the air-conditioning shutter installation position line before installation. Connect the electric welding machine, weld the hot-dip galvanized pipe on the angle steel of the hole with an electric welding machine, fix the louver blades on the hot-dip tinned pipe one by one in order from top to bottom, and fix the hole with self-drilling and self-tapping around the louver frame.

During the installation of air conditioning shutters, clean up pollutants in time and protect the finished product. When the shutters are placed, the floor is paved to protect the floor from damage.

After the installation of the air conditioning shutters, the gap between the shutter frame and the wall is filled with polyurethane foam, after the foam agent is cured, the excess foam agent is cut off with a wallpaper knife, and the 3-5mm inside the frame should be eaten when cutting, and the dirt inside and outside the window frame should be cleaned with a brush. The inner and outer mouths of the window frame are glued and seamed.

How to install air conditioning shutters.

Installation specifications: 1. Small sections and thin-walled aluminum cannot be used to make air conditioning blinds. Some masters cut corners and replace the regular aluminum window profiles with aluminum tubes, which will lead to a significant reduction in the bearing capacity of the balcony aluminum windows.

If the wind is a little stronger, it will twist, deform, or even fall off severely.

2. The strength of the aluminum profile must meet the standards of relevant materials, and it should feel very hard when folded by hand. Soft materials are not available. 3. The design should be reasonable, and the practice of large divisions should not be adopted for the sake of saving materials.

Instead of using a large sash that "floors" from the guardrail to the top, be sure to install a fixed window of 400 mm to 500 mm on the upper part and a sliding window of 1200 mm to 1300 mm underneath. Moreover, the sliding window should not be too wide.

4. Considering that the force on the aluminum alloy frame should not be too large, casement windows are generally not used for closed balconies.

5. The fixing should be firm, the vertical frame and horizontal frame of the balcony aluminum window must be fixed on the guardrail and the top of the balcony, fixed in the concrete with nails and rivets, and then quickly reinforced with painted angle steel. It cannot be fixed on the surface of a brick wall, and it cannot be fixed with a wooden wedge against the frame instead of a nail gun.

6. The high side of the aluminum window glide path should be indoors, and the low side should be outdoors to prevent rainwater infiltration. Small holes should be made on the outside of the low side to drain rainwater. All the gaps in the closed balcony should be filled with cement mortar.

Air conditioner fan disassembly and cleaning method:

1. Before cleaning the air conditioning fan, first confirm that the air conditioning fan has been shut down and unplug the power plug.

2. According to the requirements in the manual of the air conditioning fan, first remove the back cover and filter screen of the air conditioning fan, and here we need to remind everyone to pay attention to the loosening direction when loosening the fixing screws, so as to avoid the phenomenon of "overflow" when tightening tighter.

3. When cleaning the removed air conditioning fan filter, you should use neutral detergent with a soft cloth, and never use hard products such as steel wool balls to clean the filter. After confirming that the filter is thoroughly clean, the detergent should also be removed with clean water to prolong the life of the filter.

4. The air conditioning fan filter can be installed back in place after wiping it dry with a soft dry cloth, it is recommended that you try it after cleaning the air conditioning fan, if you find that there is abnormal noise or abnormal vibration, it usually means that there is an error in the installation, and the installation link can be solved by re-checking.

Precautions for cleaning air conditioning fans:

1. The outdoor unit can generally be rinsed with clean water, if it is an outdoor unit with heavy oil smoke or by the roadside, it is necessary to purchase a special air conditioning cleaner to clean it.

2. During use, the filter screen and face cover should be cleaned once every 15 days. If it is not used for a long time, the blower should be opened every 1-2 months for ventilation.

3. If there is not much oil on the face cover, it can be rinsed with clean water and brushed with a clean soft brush.

1. First of all, we wipe the shell with a wet towel and wipe the dust adhered to the shell clean.

2. Open the front panel and take out the filter, be careful not to break it when taking it out.

3. Remove the filter.

4. Take out the strainer and then take a basin of water, carefully scrub and dry it with a soft brush.

5. Reinstall the filter.

6. Take a bottle of air conditioning disinfectant and spray it evenly on the heat dissipation fins. After spraying, let the air conditioner fan stand for 10 minutes, so that the air conditioner fan is cleaned.

The method of disassembling the fan blades is as follows:1. First unplug the fan and let the fan be in a power-off state.

2. Prepare corresponding tools, such as screwdrivers, gloves, etc., to prevent hand injuries.

3. Use a screwdriver to remove the fixing screws of the fan and unscrew the nut to remove the fan blades.

4. Finally, brush the fan blades and front and rear covers, wipe off the water, and put them in a ventilated place to dry, and then install them in situ.

It is necessary to choose a qualified shape of the taper to unscrew the screw, remove it according to the time, and when screwing, the force should not be too large to prevent the screw hole from deforming and cracking. In addition, when removing the fan hoop, hold the grille first to prevent damage to the grille during the disassembly.

Steps to remove the cooling fan:1Use an extended Phillips screwdriver to remove the four screws from the inside with the screw heads facing you, then split the machine housing into two parts.

2.On the upper case, the board should be unbroken. There are two clips on both sides of the upper case.

Use a flathead screwdriver to gently pry them off and pull them out slowly so that the upper case can be removed. 3.Remove the rear chassis.

Note that the chassis at the back is connected to the power cord, and the chassis has a wire buckle. Press down on the threaded button from the inside with needle-nose pliers while pushing it out. 4.

Next, disassemble the motor, remove the triangle plate and rubber on the motor, and remove the surrounding wires from the trunking. Remove the three screws on the left and the two on the right. 5.

Finally, remove the front cover, remove the left and right screws, and the sink will have four slots. Slowly disassemble it from one side with a flathead screwdriver, and after disassembly, it can be cleaned.

Tools Required: Screwdriver.

1.First, pull both ends of the air conditioner enclosure, 2Remove the internal filter, 3

Disconnect the panel display on the air conditioner cover, 4After that, pull the baffle outward, 5Disassemble the casing of the air conditioner, 6

Remove the water storage tank inside the air conditioner, 7Then take out the **controller,8.Click on the screw on it to remove it, 9

In this way, the rotating machine can be removed,10After that, the fan blades can be removed.

Loosen the screws connecting the motor and fan with a hexagonal sleeve.

Remove the fan and clean the disassembly location. Then put in the new fan blades and tighten the screws.

Just remove the nut on the fan motor of the outdoor unit condenser and gently tap the motor, and the fan blades can be removed.

After taking it out, again, clean the fan, install new fan blades, and check that the lower motor is in place.

Air conditioning refers to the process of adjusting and controlling parameters such as temperature, humidity, cleanliness, speed of ambient air in a building structure by artificial means. Including general cold source heat source equipment, cold and hot medium transmission and distribution systems, terminal equipment and other auxiliary equipment. It mainly includes pumps, fans and piping systems.

At the end, the device is responsible for using the cold and heat from the transmission and distribution to specially treat the air and temperature to make the air parameters of the target environment meet the requirements.

It would be troublesome to remove the cross-flow fan. It is necessary to disassemble the panel, shell, and electric control box, and loosen the fixing screws and buckles of the evaporator.

That's the innermost part of the internal machine. You need to remove the noodle frame, evaporator, electric control box, and water tray before you can disassemble the fan and motor!

It can be replaced. First, remove the lid and then remove all the electrical controls. Then, remove the fan motor by unscrewing the screws on the fan motor bearing.

Then, the wind wheel can be removed. It is not easy to disassemble the fan motor. Be careful not to disassemble violently.

Turn the vaporizer on a little bit.

Air conditioning fanIn recent years, it has sold very well, but in daily use, the air conditioning fan also needs to be cleaned regularly, so let's introduce the cleaning method of the air conditioning fan.

1. Before cleaning the air conditioner fan, first confirm that the air conditioner fan has been shut down and unplug the power plug, and it should be clear that the safety of electricity when cleaning household appliances is to ensure the safety of life.

2. Remove the filter screen and back cover of the air conditioner fan according to the requirements in the air-conditioning fan manual, and it should be noted that when loosening the core and moving the fixing screw, you must look at the direction of loosening, so as to avoid tightening it in reverse.

3. When cleaning the removed air conditioner fan filter, you should use a neutral detergent, then use a soft cloth, and remember not to use hard products such as steel wool balls to clean the filter. After confirming that the filter is thoroughly cleaned, the detergent should be removed with clean water to extend the service life of the filter, and then it can be ventilated and dried to install it back in place.

4. Next is the front air outlet frame, which can be wiped with a damp rag to wipe the steering blades and wind direction blades. Open the back and head cover, open the whole air duct, clean the air duct and impeller with a damp rag, and dry it after cleaning.

Precautions for cleaning air conditioning fans:

The outdoor unit can generally be rinsed with clean water, if the outdoor unit is heavy or on the side of the road, you also need to buy a special air conditioning cleaner to clean it. During use, the filter and face cover are cleaned once every 15 days. If it is not used for a long time, the blower should be opened every 1-2 months for ventilation.

If you find that there is abnormal noise or abnormal vibration, it usually means that there is a mistake in the installation, and it can be solved by disassembling it again and installing it in the correct way.