What should I do if the screws of the Apple phone are slippery

1. Inject a small amount of 502 glue into the screw hole, then screw the screw in, wait for the 502 glue to solidify, and then use needle-nose pliers to screw out the screw (only so don't use a screwdriver for fear of causing the screw to slip);

2. Put something on the screwdriver bit, such as double-sided tape, non-woven fabric, etc., if there is really no condition, the paper can also be used, the purpose is to enhance the friction;

3. If the screw cap is exposed, you can use sharp pliers to tighten the screw cap and unscrew it. You can also cut off the screw cap and disassemble the casing before processing;

4. Burn the head of the screwdriver on the gas stove, and then quickly put it on the screw, wait for about 5 seconds, so that it can be unscrewed out;

5. The more precise the screw slip is more difficult to solve, the larger the screw, the more ways to take it out, if you encounter a large screw, you can directly use a rubber band to stuff it into the screw head, because the rubber band is elastic, use friction, and easily take out the screw.

What should I do if the screws of my mobile phone cannot be unscrewed?

Lubricate the wire mouth (diesel, kerosene), wait for a while, then hit the wire cap with a hammer (so that it has a certain gap), then repair the thread with a hacksaw, and then screw it with a screwdriver. It's really not okay to consider hacksawing off the nut. Add some lubricating oil to see if it works, weld a handle without welding.

Find a maintenance point and let the master help you tighten, and say some kind words to help you.

Dear, hello, thank you for your question, this side will serve you wholeheartedly, if the service is not good, please include more, the questions you ask are as follows: 1, first of all, increase the friction between the screwdriver and the screw, so you can bury the screwdriver or screw head pad something, such as double-sided tape, non-woven fabric, or paper and the like. 2. Solidify directly with 502 glue, pour a small amount of 502 glue into the screw, and use needle-nose pliers to screw out the screw after the 502 glue bend water solidifies. 3. If the screw has come out partially, for example, the screw cap is out, you can directly use needle-nose pliers to tighten the screw cap and unscrew the screw.

4. A more barbaric method is to burn the head of the screwdriver red on the gas stove, and then quickly put it on the screw, and wait for about 5 seconds to screw it out directly. Thank you for your question, and have a great day.

Summary. The screw at the bottom of the Apple mobile phone generally can't be taken out, either slippery wire, or slippery teeth, sliding wire refers to the length of the screw where there are a few wires missing, which are worn off.

If it is a slippery tooth, it is a five-pointed star on the head of the screw, and the use of an improper screwdriver causes the five-pointed star to be rounded.

The specific steps to solve the problem are as follows:

1. If it is a slippery wire, put some double-sided tape on the head of the screw, and then use a professional screwdriver, you can screw the screw out again If it is a slippery wire, it is generally easy to take out, but it cannot be installed, and it will feel very loose;

2. If it is a slippery tooth. With double-sided tape, a drop of 502 glue can solve the problem within the pentagram. Find the place where the screw at the bottom of the iPhone is slippery and can't be unscrewed.

3. Place one end of the rubber band on the screw of the sliding wire. Then use a screwdriver to hold down the rubber band and twist it together with the screw, so that the iPhone screws are quickly screwed out.

Hope mine can be helpful to you.

What should I do if the screw at the bottom of the Apple phone is slippery and I can't get it?

Hello, I'm glad to answer for you I'm talking about emotions in clothes, and my questions are answered by me. I'm typing for you to solve the problem, it will take about 5 minutes, don't worry, please wait a while.

Hello, I'm glad to answer for you The screws at the bottom of the Apple mobile phone generally can't be taken out, either slippery, or slippery, and the slippery wire refers to the length of the screw, where a few wires are missing, which are worn off. If it is a slippery tooth, it is a five-pointed star on the head of the screw, and the use of an improper screwdriver causes the five-pointed star to be rounded. The specific steps to solve the problem are as follows:

1. If it is a slippery wire, put some double-sided tape on the head of the screw, and then use a professional screwdriver, you can screw the screw out again If it is a slippery wire, it is generally easy to take out, but it cannot be installed, and it will feel very loose; 2. If it is a slippery tooth. With double-sided tape, a drop of 502 glue can solve the problem within the pentagram. Find the place where the screw at the bottom of the iPhone is slippery and can't be unscrewed.

3. Place one end of the rubber band on the screw of the sliding wire. Then use a screwdriver to hold down the rubber band and twist it together with the screw, so that the iPhone screws are quickly screwed out. Hope mine can be helpful to you.

Summary. 1. First of all, it is necessary to increase the friction between the screwdriver and the screw, so you can put something on the screwdriver or screw head, such as double-sided tape, non-woven fabric, or paper. 2. Solidify directly with 502 glue, pour a small amount of 502 glue into the screw, and unscrew the screw with needle-nose pliers after the 502 glue solidifies.

3. If the screws have been.

1. First of all, it is necessary to increase the friction between the screwdriver and the screw, so you can put something on the screwdriver or screw head, such as double-sided tape, non-woven fabric, or paper. 2. Directly solidify with 502 glue, pour a small amount of 502 glue and pour it into the snail silk, and wait for the 502 glue to solidify and use needle-nose pliers to dig the screw out. 3. If the screws have been.

Can you add, I don't quite understand it.

1. Pad something on the screw wire, such as double-sided tape, non-woven blind judgment cloth, etc., if there is really no condition, the paper can be milled and changed, so that the friction can be increased, and the screws of the slippery silk can be removed. 2. Inject a small amount of 502 glue into the screw hole, and then screw the screw in, and then use needle-nose pliers to screw out the screw after the glue solidifies.