What to do if the kitchen drain is always dirty?

Stay away from greasy kitchen sink cleaning tips The sink is the heart of the kitchen. According to statistics, the use rate of sinks is the highest in the kitchen. More than 65% of the time in the preparation and cleaning before and after meals is directly related to the sink, so it is very important to choose a sink, which is beautiful, good performing, and clean, to build a comfortable and warm kitchen.

Kitchen Sink Cleaning Kitchen sinks are always greasy and not easy to clean. Sometimes, even if you use dish soap to clean it, it won't shine brightly. Let's teach you a clean kitchen.

Keep away from odors Kitchen Floor Drain Cleaning Tips Floor drains are an important interface connecting the drainage pipe system to the indoor floor, as in the home.

1. Flush with boiling water, most of the sewer plugs are grease blockages, and the boiling water can be dissolved. 2. The best way is to call ** to ask the housekeeper to come, and get rid of the disease. 3. If it is oily, you can use 20% Sufangda water to get through.

It can be installed directly at the drain.

If there is a leak in the kitchen, you should first find the leakage point such as the faucet and sink, and then choose to repair or replace the water pipe.

Close the water valve in the kitchen to prevent water from overflowing and increasing losses. Then look for the source of the leakage, the common ones are water pipe joints, faucets, sinks and other parts, you can carefully inspect the connection points and components. If there is a visible crack or breakage, temporarily seal it with a wrench or cement and wait for repair.

If the leakage point is not obvious, you can put some paper towels at the door and around the element, and observe that the paper towel is wet as soon as possible, and it is likely to be the leakage point. Then the water leakage point is exposed, and after the cause of the water leakage is found, the maintenance method is selected according to the situation. If the water pipe breaks, the leaking section can be cut off and replaced with a new one.

Broken faucets or sinks can be replaced with new parts, and loose joints can be tightened or re-wrapped and sealed. These simple repairs can be carried out according to the individual's ability and can also be handled by a professional plumber and electrician.

How the kitchen is waterproof

1. Choose a waterproof material.

Choose waterproof and non-slip tiles, floor tiles and other materials for kitchen floors and walls, and stainless steel or waterproof materials for cabinets and sinks.

2. Do a good job in the installation of water pipes and hydropower.

For the installation of kitchen water pipes and water and electricity lines, waterproof and high-temperature resistant materials should be selected, and the interface should be tightly sealed to prevent water leakage. Regularly inspect water pipes and faucets for damage or leakage.

3. Install drainage facilities.

Floor drains and sink drains should be installed in the kitchen to protect the kitchen from flooding. The floor drain mesh should be selected appropriately to prevent lost objects from blocking, and it should be cleaned regularly to ensure that it is unblocked.

4. Keep cabinets and walls tidy.

Cabinets and kitchen walls should be cleaned regularly to avoid discoloration and leakage due to long-term oil accumulation. The range hood should be cleaned and degreased regularly to prevent oil from flowing to the walls and ceilings.

Kitchen leakage can be solved by doing ground waterproofing, cabinet baseboard, etc.

1. Do ground waterproofing.

The most serious water seepage in the kitchen is the broken connection of the water pipe, or the leakage due to the poor connection. In this case, once the water leaks, the kitchen floor will be full of water, which will not only affect the use of the house, but also affect the residents downstairs in serious cases. Therefore, when decorating the kitchen, it is best to do the work of the floor.

Directly on the ground below the kitchen sink water pipe, even if water seepage occurs in the later stage, it will not affect the downstairs residents and bring losses to themselves. In the same way, this waterproof method is also suitable for use in bathrooms, balconies and other places with many water pipes.

2. Make cabinet baseboards.

Once the kitchen water pipe leaks, the degree of leakage can be large or small, and if the water seepage is serious, water will flow into the cabinet. Nowadays, most of the cabinets in the home kitchen are made of wood or MDF, and if they are soaked in water for a long time, it will affect the use of the cabinets.

In this case, a baseboard can be designed under the kitchen cabinet to act as a barrier, making it difficult for water on the floor to enter the cabinet. It is worth noting that it is best to choose waterproof materials for the baseboards of cabinets, not as good as PVC materials, stainless steel, etc.

How do you prevent water leaks in the kitchen?

1. Choose materials that prevent water distribution.

The kitchen is a special area in home life, because we will use a lot of water and sails in daily use, so it is recommended that you try to use waterproof materials when decorating, which can not only make the whole space look more refreshing and clean, but also extend the service life of the kitchen.

2. Design a waterproof platform.

Although many people choose undercounter basins when installing sinks, which can reduce water overflow, it is inevitable that water will spill out when we wash and scrub when we cook, making the countertop wet. Therefore, it is recommended that you try to make a waterproof platform for the sink when decorating, which not only looks more beautiful, but also avoids water splashing.

3. Choose an undercounter basin for the sink.

Whether it is washing dishes, washing vegetables, or washing kitchen utensils should be carried out in the sink, if you install a countertop basin, it is easy to let the water spill out when you use it, making the kitchen wet, so it is recommended that you try to install an undercounter basin better, so that you can reduce water overflow.

1. First of all, you need to find the cause of water leakage, if there is a problem with the waterproof layer, there are usually two ways to deal with it: local plugging or overall re-waterproofing. However, not all water leakage situations can be solved by filling the leakage, and it is not necessary to re-do the waterproofing as a whole when encountering water leakage, and the specific situation needs to be analyzed in detail.

2. Replace the connecting parts. This is mainly for kitchen sinks, the biggest reason for the leakage of the sink pipe joint is that the cap nut of the faucet is loose, as long as the cap nut is re-tightened or replaced with a new gasket can solve the problem immediately. In normal times, it is necessary to prepare kitchen accessories to facilitate subsequent maintenance and use.

3. Welding interface. This is mainly for the leakage of water pipes, kitchen water pipe leakage to dig the wall tiles, find the joint part of the water pipe, find the leaking water, re-weld the water pipe joint, and then re-do the waterproofing of this range, and finally post building materials such as tiles and wall tiles.

4. If the leakage is small, the leakage area is small, and the leakage point can be accurately found, the method of repairing and plugging the leakage can be used to deal with it. The specific operation method is to pry open the tiles near the leakage part, expose the base surface, chisel the leakage point into a "V" groove, and use a special permeable crystalline repair mortar to repair and plug the leakage, which can be solidified in about 10 minutes, and then paint a kitchen and bathroom waterproof slurry around the repair place.

5. If the water leakage is serious, and the leakage area is large, or the specific leakage point cannot be accurately found, the problem can not be completely solved by filling the leakage, and then it is necessary to re-do the waterproofing as a whole. The specific method is to remove the tiles and other decorations on the surface as a whole, expose the base surface, clean the base surface and clean it, first repair and level the gaps or potholes with penetrating crystalline repair mortar, and then paint the kitchen and bathroom waterproof slurry as a whole. The waterproof layer is dry thoroughly, and the process of tiling is carried out after passing the closed water inspection.

1. When you find a kitchen leak, you must first find the cause of the kitchen leakage and the specific location of the leakage, and then choose the appropriate maintenance method according to the actual leakage and severity. If the cause and location of the leak are different, the maintenance method will be different.

2. If there is a leakage in the kitchen pipe, you need to check the specific location of the leaking pipe. If there is a leak in the water pipe, it is easier to repair, because the water pipe is usually routed from the ceiling position.

3. During maintenance, you need to open the ceiling, turn off the water inlet valve, and then use leakage materials to repair the leakage position, or replace the pipeline directly with a new one. If the sewer pipe is leaking, it will be more troublesome and you need to ask a professional to help repair it, but the sewer pipe leakage phenomenon generally does not occur often.

4. If there is water leakage on the ground, you need to do the waterproof construction again. Before construction, it is necessary to knock off the tiles on the kitchen floor, and clean up the dust and dirt on the ground base, and the ground is dry. Apply about 2 more waterproof paints, and finally re-lay the floor tiles.

1. You need to check the kitchen sewer pipe, and you must find the best leakage, if it is an open pipe, it is easier to find, if it is a dark pipe, it will be much more troublesome, and you have to press the water pipe to know which water pipe is leaking.

2. Suppress first, the method of suppression is to connect the hot and cold water pipes together with a hose, then close the main valve, and leave a nozzle to connect to the pressure pump for pressure. Look at the pressure gauge of the pressure pump to stop between pointing, and then wait for half an hour to check the pressure value, if the number does not exceed the drop, then there is no leakage.

3. Now that the leakage point has been found, the next step is to fill the leakage. There are some cases of leakage in the kitchen pipe just because the joint is a little loose or degummed. What should I do if the kitchen water pipe leaks in this case, the interface is loose, and it can be tightened, and then the main thing is to prevent leakage later, so the interface has to be waterproofed, and the waterproof glue can be brushed.

Then I had to have a kitchen water pipe leaking because the water pipe was aging and cracking. Change the pipe, find the leaking section of the pipe, use a small saw to saw off the leaking place, then cover it with an interface, then connect the newly bought sewer pipe joint with the old water pipe joint, and finally use a hot melter to hot melt connect the new pipe.

1. When the kitchen leakage is small, the leakage area is small, and the leakage point can be found correctly, it can be treated by repairing the lock. The specific operation method is to pry open the tiles near the leakage, expose the ground, cut the leakage point into a "V" shaped ditch, repair the leakage with a special permeable crystalline repair mortar, solidify it for about 10 minutes, and apply kitchen protective waterproof paste around the repair place.

2. The kitchen leakage is very serious, the leakage area is very large, or the specific leakage point cannot be found correctly, the trap method cannot completely solve the problem, so it is necessary to re-waterproof the whole. Specifically, the surface tiles and other decorations are removed as a whole, the base surface is exposed, the base surface is clean, and the gaps and depressions are repaired with a repair mortar soaked in crystalline to smooth them, and the waterproof paste of the kitchen and bathroom is applied as a whole. Wait for the waterproof layer to dry up, turn off the water and pass the inspection, and then carry out the process of tiling and other processes.

How do you do kitchen waterproofing? 1. First of all, the construction site should be cleaned up, and it should be sprinkled with water to make it fully moist but there can be no stagnant water, so that it is convenient to carry out the construction with a better number of clever talks.

2. The basic layer of the waterproof layer should not be uneven, loose or hollow, and the moisture content should be less than 10%. The waterproof layer should be firmly pasted, not blistered or wrinkled, the floor drain and drainage port should be kept unobstructed, and protective measures should be taken during construction.

3. For kitchen waterproof construction, first bury the drainage channel, clean the ground base, scrape a layer of plain cement slurry to dry and brush the waterproof material for the second time, or you can do the wall waterproofing first.

4. When redecorating the ground, it is easy to damage the waterproof layer, and if it is not repaired in time, leakage will still occur in the future.

5. The variety and quality of waterproof materials must meet environmental protection standards, and the products must be certified by the factory certificate.

Analysis of the causes of kitchen water leakage (1) If the structure of the kitchen is more complex when building the house, there are more water pipes in the kitchen, the corners of the wall are more than filial piety, and the plane and façade joints of the wall are more, which brings greater difficulty to the construction of the water pipe decoration, and this difficulty may also lead to the construction effect not reaching the best, which may cause the phenomenon of kitchen water leakage.

2) The daily water consumption of the kitchen is relatively large, and the number of daily contact with water is more, if in this case, the drainage design in the early stage is not in place, it is easy to have the problem of long-term water accumulation, and the long-term water accumulation in the kitchen is one of the causes of kitchen leakage.

3) The corrosion of detergents or daily chemicals often used in daily kitchens on water pipes and waterproof layers, the corrosion of detergents and daily chemicals will cause the aging of the waterproof layer, and even the failure of the waterproof effect, which is an important cause of kitchen leakage.

4) The deformation of the joints such as the drainage pipe of the kitchen, the vicinity of the floor drain, and the corner of the kitchen wall leads to the phenomenon of kitchen water leakage. If there is a leak at the joint of the pipe, it is because the cap nut is loose, which will directly lead to the leakage of the joint of the pipe, and finally, the phenomenon of water leakage in the kitchen.

<> "How to deal with kitchen leakage.

1. First of all, find the cause of the water leakage. If there is a problem with the waterproofing layer, there are generally two ways to solve it: partial blockage or overall watering.

However, not all leaks can be solved by filling them, and it is not necessary to re-waterproof them all as soon as they are discovered. The specific situation should be analyzed on a case-by-case basis.

2. Replace the connectors. This is mainly used for kitchen sinks. The most likely cause of a leak at the sink joint is a loose faucet cover nut.

Simply re-tighten the lock nut or replace the washer with a new one to solve the problem immediately. In general, kitchen accessories should be prepared to facilitate subsequent maintenance and use.

3. If the leakage is small and the leakage area is small, the leakage point can be accurately found, and it can be repaired by repairing the plugging method. The specific operation method is to open the tile near the dripping part to expose the base surface, chisel the leakage point into a "V" shaped groove, first repair the leakage with a special permeable glass repair mortar, and wait for the leakage to solidify. After about 10 minutes, then apply a piece of waterproof kitchen and bathroom grout around the repaired area.

4. If the water leakage is serious, the water leakage area is large, or the specific leakage point cannot be accurately found, the problem cannot be completely solved by using the leakage repair residual recovery method. At this point, the assembly needs to be re-waterproofed.

There is water on the kitchen floor and it is **leaking.

If the inlet pipe connection is not in place and there is a water leakage, or the sewer pipe seeps, you can close the water inlet valve, and then check whether the leakage will continue to leak, and then check whether the connection of each interface will seep, if not, then check the sewer, prepare a large amount of water to flush into the floor drain, check whether the ground will seep, if so, it means that the sewer leakage causes water on the kitchen floor, which can be excluded according to the specific situation.

Introduced the content answer about the water on the kitchen floor is the first leakage, I hope it helps.