Why should the firewood stove in the rural province set up a fire ring? What is its purpose?

The fire ring is the position between the upper end of the combustion chamber of the firewood stove and the bottom pot, which is also called the fire ring and the fire ring. The function of the fire ring is to adjust the orientation of the flame and the smoke cycloneto manipulate the flow rate of flue gases and increase the time for flammable gases to burn and stay in the stove. Because of the effect of the heat-collecting reflective surface of the fire-stopping ring, the heat generated by firewood.

It has been digested and absorbed by the pot wall several times, which further improves the efficiency of heat utilization. The bottom pot shaped fire ring encloses the pot under the pot, and the size of the gap between each position of the fire ring and the pot wall is used to adjust and manipulate the flow speed of the flue gas.

In the past, these firewood stoves in the countryside were just a simple stove, and the burning of firewood was only a whole process of natural burning, so not only the burning efficiency was not high, but also the firewood was more consumed. The current firewood stove has a fire ring that can not only make the combustion more sufficient, but also make the flame become a regular, directional, and long-term operation method, instead of the smoke that has not burned thoroughly after the previous burning, all of which are directly discharged into the chimney, so the setting of the fire ring has become an important part of the characteristics of the kitchen stove.

A ventilation duct is set up at the bottom of the middle of the stove of the fire-saving stove, and the firewood is burned to the stove according to the ventilation duct below when the fire is made, so that the firewood in the stove burns more thoroughly, and the fire point is more violent, in order to better enhance the calorific electric field in the stove and achieve the purpose of saving firewood, when the firewood saving stove is built, let the bottom pot reduce the distance between the bottom pot and the bottom of the stove as much as possible, so that the burning surface of the wok--hying pot can be maximized, so that a ring-shaped cyclone circle is formed invisibly on the top of the hemispherical shape of the wok and the inner cavity of the stove.

In the case of application, the smoke and fire first go backward from the stove to the opposite side, and then be blocked by the fire rain, along the two sides of the fire ring from both sides to the stove direction, and then from the top of the stove to the left and right sides backward into the smoke outlet and chimney. Reduces the rate of the fireworks flow and saves as much heat as possible to the pot. The use rate of firewood has been further improved, and it can be burned.

But there are certain regulations for chimneysBe sure to pull (smoke) strongly, otherwise the fire in the stove will be prosperous, and the friction resistance will be large, and the smoke will not be good; Second, the combustion is not sufficient, and the actual effect of saving firewood cannot be achieved.

Because this method will be more convenient to use in rural stoves, the pot can be made more even, and the liquid can be drained cleanly and firewood saved; The main purpose is to gather heat, to prevent the fire from being pumped away, to make the flame closer to the bottom of the pot, and to make the bottom of the pot evenly heated, while the fire is concentrated, it can also prevent the leakage of wind and smoke, and can improve the utilization rate of heat energy, and can also save firewood.

The fire ring in the firewood stove can prolong the time for the flame to stay in the stove, improve the combustion efficiency and the temperature in the stove; The purpose is to save firewood and effectively improve the efficiency of combustion.

It is for fear that the fire will be uncontrollable and cause a relatively large natural disaster, everything is from the perspective of safety, and the other is also for the aesthetic effect.

The high-temperature flue gas produced by firewood combustion is limited by the fire ring and discharged from the chimney through the return flue through the flue to form a mountain-resistant natural exhaust. The reasonable gap between the fire ring and the pot is used to adjust and control the fire, so that the pot is evenly heated, so as to achieve the effect of clean smoke exhaust and saving firewood.

Dear, I am glad to answer for you: the distance between the firewood stove and the pot Hello The distance between the firewood stove and the pot can be kept at about 30 cm to 40 cm, so that the space for burning firewood is more sufficient, and the amount of firewood is relatively large. The fire digging circle must be tried to burn several times to finalize, with clay mixed with hemp knife and hard mud to smear into the shape of the bottom of the pot, as the first billet, the thickness is not less than 50mm, and then use the primary billet to cut out the pot ring, exhaust flue, return flue line, the thickness of the pot ring is 25mm, the thickness of the fire ring is 30mm, the exhaust flue, the smoke return is only 30-40mm deep, the width is 50-80mm, and the groove is cut 30mm deep along the line with a trowel.

Provincial firewood stove is a new type of stove, which saves fuel, has high calorific value, emits less smoke and dust, and is a living facility worthy of promotion and utilization in rural areas, especially in mountainous areas. By the way, some experts have recently opposed the use of clay wood stoves for cooking in rural areas, saying that it is a polluted air to judge the mountains, and it is undeniable that cooking on fire must produce a certain amount of smoke and dust, which is not completely harmful, and carbon dioxide is the main nutrient absorbed by plants after conversion.

Kiss <>

Hello <>

The distance between the firewood ring and the pot is as follows: the distance between the bottom of the firewood stove can be kept at about 30 cm to 40 cm, so that the space for burning firewood is more sufficient, and the amount of firewood is relatively large. The fire ring must be tried to burn several times to finalize, with clay mixed with a knife and hard mud to smear into the shape of the pot to rise to the bottom, as the first billet, the thickness is not less than 50mm, and then use the primary billet to cut out the pot ring, exhaust flue, return flue line, the thickness of the pot ring is 25mm, the thickness of the fire ring is 30mm, the width of the dry exhaust flue, the depth of the return flue is 30-40mm, the width is 50-80mm, and the depth is 30mm deep out of the smoke trough along the line with a trowel.