The bottom of the compound pot of the small steamer has fallen, what should I do? Boiled the pot dry

The bottom of the compound pot of the small steamer is burned off, just throw away the layer of composite bottom directly, the small steamer can still continue to be used, and then use the small steamer, the same amount of water, heating faster, the possibility of drying the pot is greater, pay attention to adding water in time when using, so as not to burn the dry pot again.

If the steamer can still be used, there is no damage in other places, and there is no place to hurt your hands in the outer compound, then it can still be used, there are two layers of pot bottom just to keep warm, and many of the steamers produced now do not have this composite bottom, so it can still be used.

When the bottom is doubled, the aluminum sheet is melted off at a high temperature (melting point), and then the compound negative with magnetic conductivity is glued together with the bottom of the pot through professional equipment. Therefore, the bottom of the pot is off, and consumers have no way to repair it by themselves, but they can buy a special thermal conductive sheet pad at the bottom of the pot, which can also play a role in heat conduction.

If the steamer is rebuilt, there is no way to repair it by yourself, and it may affect the life of the induction cooker if it is barely repaired. However, you can buy a special thermal conductive sheet pad at the bottom of the pot, which can also play a role in heat conduction.

The steamer can't be repaired if it's low, so you can directly remove it and then use it again, because most of the pots are composite, so they can't be repaired.

The compound bottom of the small steamer has fallen off, and it has no use value, so you can throw it away directly and buy a new pot.

The bottom of the small steamer can only be sold or thrown away as scrap, and it cannot be repaired by itself.

Is it the kind of stainless steel pot with a thick bottom? There is aluminum in it, mainly for both induction cookers.

Gas stoves can be used and heat transfer is fast and even. You can continue to use it. It is recommended to use an induction cooker in the future, which not only saves energy, but also schedules. lest the steamer become a toaster again.

Compound pot should remember not to dry boil, boiling the pot is easy to fall off the bottom bulge deformation, only to change the bottom of the pot or change the new pot.

What should I do if the bottom of the compound pot of the small steamer falls off, so the dry pot is off? If it is said to be burned. At. You can find a welder to weld it and see if you can weld it, if you can't be tough, just throw it away, and then buy a new one?

The bottom of the small steamer has fallen off. So what to do? Just buy a new one. I can't use it if I drop the bottom, so I need a new one.

The bottom of Xiao Zeng's compound pot fell off, so throw it away, right? Let's get a new one! It's rare to see the bottom of the pot repaired now.

Use tongs to peel off the broken bottom of the pot and it will still work normally.

It's burned, and if it can still be used, it can be used again, and if it can't be used, it will be replaced with a new one.

You don't need to deal with it, just throw it away. It's time for a new one.

Let's change it, and if you can't help it, find a way to fix it.

In this case, I think you have to choose to change the pot again.

If the bottom of the small stainless steel pot is boiled dry and black scale, you can find a large container, fill it with water and put some pineapple skin, and then put the small pot into the container, **heat until the water boils, boil for 20 minutes to 30 minutes, take out the small pot, gently wipe it with a cloth, and the black scale can be removed.

If it is an aluminum pot, do not clean it with a steel wool ball, which will destroy the protective film on the pot, you can heat the apple peel and cook it, and then use them to wipe the black scale, the effect is good. You can also put a little water in the pot, put a few slices of chopped tomatoes in it and cook it, then pour out the tomatoes, and then wipe the bottom of the pot with a rag to remove the black scale. If you don't want tomatoes, you can use half a bowl of white vinegar or a handful of tea leaves instead, and the effect is the same.

If the bottom of the iron pot is boiled, you can put the pot on the stove, dry it for a while over low heat, and when the pot is smoking, sprinkle some salt, shake for a minute to turn off the fire, and then wipe it with a cleaning ball, which can remove the black dirt and will not leave a bad smell.

Summary. If the steamer can still be used, there is no damage in other places, and there is no place to hurt your hands in the compound outside, then it can still be used, there are two layers of pot bottom just to keep warm, and many of the steamers produced now do not have this composite bottom, so it can still be used.

The bottom of the compound pot of the small steamer has fallen, what should I do? Boiled the pot dry, so it fell off

Dear If the steamer can still be used, there is no damage to the slag in other places, and there is no damage to the outside compound, then it can still be used, there are two layers of pot bottom just to imitate the effect of maintaining the temperature of the family, and many of the steamers produced now do not have this compound bottom, so it can still be used.

Dear When the bottom is doubled, the aluminum sheet is melted off at a high temperature (melting point), and then the double bottom with magnetic conductivity is glued together with the pot hole only bottom through professional equipment. Therefore, the bottom of the pot is off, and consumers have no way to repair it themselves, but they can buy a special thermal conductive sheet pad at the bottom of the pot, which can also play a role in beating and conducting heat.

1.After refilling the water tank, the water refill indicator still flashes. Reason: Clean the sensor, or the sensor is damaged and need to be replaced in time.

2.No steam, no heat. Reason: Heating plate failure, timely repair.

3.It can be used when it is turned on in low gear, and it will be powered off when it is turned on in high gear. Cause: It may be caused by the main control switch of the power supply being too small. Replacing the appropriate switch will solve the problem.

4.The indicator light is not on. Cause: power cord burned, repaired or replaced; The contact of the stabilizer is not in good contact, and it can be removed after cleaning it with sandpaper sand! If the indicator lamp itself is faulty, it will be replaced with a new one; The thermal fuse blows out, and it is replaced with a new one.

5.When the electric steamer is operating, it is intermittent. Causes and countermeasures: Because there is an open circuit and it is not completely disconnected, the connection between the wire coil and the screw is loose, you can disassemble the electric steamer after the power is off, and tighten the screws.

6.Cook rice sandwiched raw. Reason:

If the magnet is damaged, the starting temperature of the magnet will jump when it is less than 103 degrees, and the temperature of the cooking will not reach the normal value at the right time, forming a pinch growth. The magnet is not properly debugged and adjusted from scratch. The contact of the heating switch is poor, and it should be cleaned with sandpaper sand.

Summary. See what kind of reason is broken, after filling the water tank with water, the water lamp is still flashing, it may be that the sensor is cleaned or the sensor is damaged to be replaced in time, there is no steam coming out, when there is no heat sensation, it may be that the heating plate is faulty and needs to be repaired in time.

See what kind of reason is broken, after filling the water tank with water, the water lamp is still flashing, it may be that the sensor is cleaned or the sensor is damaged to be replaced in time, there is no steam coming out, when there is no heat sensation, it may be that the heating plate is faulty and needs to be repaired in time.

Fellow, I really didn't understand, I can be more specific.

There are several reasons why a steamer is bad, and it is necessary to find the reason. My steamer indicator light is not on, it may be that the power cord is burned out, and it needs to be repaired or replaced. If the heating plate is faulty and the steamer cannot be heated, it needs to be replaced.

The steamer is intermittent when it works, it may be because there is an open circuit, and it is not completely disconnected because the connection between the wire coil and the screw is loose, you can disassemble the electric steamer after the power is off, tighten all the screws and turn it on again.

Kiss! Hello, happy to answer your <>

The solution to the problem of falling off after the bottom of the pro-composite pot is burned dry is as follows: first, it can be repaired by rivets, first through electric drill drilling, the rivets are implanted with tongran, and then smashed flat, and finally polished, which can stabilize the two layers; Second, if there are conditions or choose the way of welding, prepare the argon arc welding cold welding machine, and then choose the white steel potion, but also prepare the white steel electrode, through the technology of argon arc welding, the two parts of the bottom layer can be effectively combined, and it is not easy to separate in the later stage. The composite pan is characterized by:

Between the bottom of the pot body (1) and the vapor chambering plate (2), it is pressed and riveted by a riveting device and then brazed and compounded as a whole. The designed riveting device fundamentally solves the problem of cracking or desoldering due to the creep caused by the different thermal expansion coefficients of the two materials compounded together, and has the advantages of firm connection between the pot body and the vapor chambering plate, reliable quality and uniform heating. 1. Made of high-quality stainless steel base materials, thick and tough, retaining the classic traditional style of European Germany, and durable.

2. Three-layer right-angle composite bottom, fast heat conduction, uniform heating; Long heat preservation time, energy saving and time-saving, durable and non-sticky; It is suitable for a variety of heat sources such as induction cookers. 3. New handle, novel and fashionable, laser printing, scientific and labor-saving, heat insulation and anti-scalding, hygienic and comfortable. 4. The close cooperation between the visible glass combination lid and the pot body produces a "water sealing effect" and effectively retains the nutrients of the food from loss; Cooking at low temperature is healthy and environmentally friendly.

5. The folding conical pot body design is fashionable and reasonable, in line with the needs of modern life, practical and full of a sense of the times. Hope mine can help you <>

Do you have any other questions?

The small pot in the dormitory, there is no water in the pot, it is steamed directly, and the steamer is cooked, but the pot is like burnt, take it to search for reeds and rinse the world with it, wash it and wash it, and guess it, if you continue to use it, it should be fine, right?

Hello. It is not poisonous, but the food will have a burnt taste, which will affect the taste. The thermal conductivity of stainless steel is not large, the heat dissipation at the bottom is slow, and the temperature is easy to concentrate, so when using stainless steel cookware, the fire power should be carefully controlled, so that the heating surface at the bottom of the search is wide and uniform as much as possible, which can not only save fuel but also prevent the food at the bottom of the pot from burning.

Stainless steel pots and pans should avoid colliding with sharp and hard objects, otherwise they will cause scratches and scars in the pots, which will not only damage its appearance, but also affect the sealing performance of the pots. When the rusty steel pan is used for a period of time, a layer of mist will form on its surface, causing the surface of the cooking utensils to darken. This should be wiped with a soft cloth dipped in powder or a mild detergent to restore the shine and cracks.

This can also be done if the outer layer is blackened by fumes. The pot is burned until there is no water, as long as the pot does not burn through the bottom, and then use a steel wool ball to wash the burnt smell, this pot can still be used, if your pot is coated, and then the boiling water is burnt, then you can't use the cleaning ball to scrub, you can only use the loofah to slowly scrub, after washing, this pot can still be used, it will not affect your future cooking and boiling water.