What should I do if the gas stove or the outside does not enter the stove?

What should I pay attention to when using a gas cooktop safely?

When ignition, if the fire does not ignite three times in a row, you should pause for a while, wait for the gas to dissipate, and then restart the fire. Pay attention to the combustion situation, such as yellow flame, fire or flame detachment, you can adjust the damper handle at the bottom of the stove until a stable, clear blue flame appears. Always check whether the hose connected to the cooker is aged, whether the connection at both ends is tight, and if it is found to be loose, it should be re-tightened.

Clean the fire holes on the stove cover regularly to prevent clogging. Once the stove fails, it should be stopped immediately and the stove manufacturer should be contacted for repair.

Common sense of gas hose use:

1. What material problems usually occur in the gas hose in use?

First, the hose selected is not a special oil-resistant hose for gas, because the material is not corrosion-resistant, it is easy to age and harden. Second, the hose used exceeds the two-year service life, and the hose loses its elasticity due to aging, and is easy to loosen and fall off under the action of external force, causing gas accidents.

2. What are the connection problems of the gas hose in use?

First, the two ends of the hose are not fully inserted into the root of the gas connection of the gas pipe and gas stove. The second is that the two ends of the hose are not fixed with special fasteners. The third is that the fastener is installed in an incorrect position.

The problems of the above three links are difficult to ensure the tightness and firmness of the joint, and it is easy to cause the hose to loosen and fall off under the action of external force. In order to save trouble, some users use thin iron wire for fixing, which is unreliable, because thin iron wire is easy to rust and break, and then loses its fixing effect.

In my memory, the pot stove has roughly gone through the following stages: wood stove, stove stove, gas stove, induction stove, natural gas stove.

If the gas stove or the outside does not enter the stove, you can talk to him to find out if there is a blockage.

<>1.There are two reasons why the inner ring of the gas stove does not catch fire, the first is that the damper of the small fire ring in the middle is not opened. The second is that the nozzle is blocked, and the induction needle is not burned when the fire is fired;

2.The reason why the outer ring of the gas stove does not catch fire is that the fire groove of the outer ring fire cover is blocked, and the fire can be normal if the blockage in the fire groove is cleaned up;

3.The reason why some fire holes do not catch fire is that the fire holes are blocked by water or other items, and it can work normally if the blocked foreign objects are cleaned up.

This answer is applicable to most of the gas stove models of brands such as Midea JZT-Q230B && Fotile EMC5.

The treatment method of gas stove is as follows:1. If there is no battery in the gas stove or the battery is rusty, we need to replace the battery in time.

2. If the gas path is blocked, we must dredge the gas path in time.

3. If the nozzle of the gas stove is blocked, we must dredge the nozzle in time.

4. If the parts or other components are aging, we must replace them in time and repair them carefully.

The solution to the gas stove is as follows: 1. Check whether the gas source is normal, if it is an ancient desktop stove with piezoelectric ignition device, the possibility of blockage of the valve core or nozzle cannot be ruled out. 2. The current furnace should check whether the battery is charged, or replace the battery and try again.

If it is not the battery, the spool and nozzle should be considered. 3. Open the switch knob to check whether there is air leakage, and whether the flame-out protection is old and bad. In this case, repairs should be carried out by professional maintenance personnel.

Summary. Hello to your question: what should I do if the gas stove valve does not work?

The answer is: just make the air intake door smaller! Don't understand the air intake switch as a liquefied gas switch, the air intake is at the bottom of the gas stove switch, there are two adjustment switches, you try to adjust the two until you adjust to the ideal state.

Hello to your question: what should I do if the gas stove valve does not work? The answer is:

Just make the air intake smaller and greater! Don't understand the air intake switch as a switch for liquefied gas, the lead spring gas is at the bottom of the gas stove switch, there are two adjustment switches, you try to adjust the two until you adjust to the ideal state of Huai leakage.

Hold up the gas stove by hand, and there are two iron pieces with handles at the connection between the burner and the nozzle blade, one of which regulates the small fire and the other regulates the large fire; They are attached to the burner by spring, and the handle of the spring sock can be adjusted to adjust the size of the air inlet to change the state of the flame.

When there is an ideal situation of burning bush hunger, such as yellow fire, black fire, flame is too large or too small, or there is combustion noise, backfire, etc., a more ideal combustion condition can be achieved by adjusting the size of the air intake at the damper. Hold up the gas stove by hand, and at the junction between the burner and the nozzle there are two strong iron plates with handles, one of which regulates the small fire and the other regulates the large fire; They are all attached to the burner by springing, and the size of the air inlet can be adjusted by gently toggling the handle, thus changing the state of the flame. When there is an unsatisfactory combustion situation, such as yellow fire, black fire, excessive flame or too small flame.

Summary. Kiss Glad to answer for you The gas stove valve does not work, it can be like this: if it can be removed, use a thin steel wire to pass the gas circuit (metal part) of the stove.

Use a needle to pass through, or use an iron bristle brush, brush it. Between the combustion valve and the burner, there are two nozzles, one in the middle of the nozzle tube, and the other in the outer ring of the nozzle tube. If you look at it, it may be that the nozzle with fire coming out of the outer ring of the tube is blocked.

If your stove is liquefied, the two nozzles have only a center aperture of ,. Easy to block. You can use a wrench to remove the nozzle and see if the middle is open.

After putting it back in, check it for air leaks with an open flame or soapy water.

Kiss I'm glad to answer before laughing at you The gas stove valve doesn't work, you can do this: if it can be removed, use a thin steel wire to pass the gas circuit (metal part) of the stove. Use a needle to pass through, or use an iron bristle brush, brush it.

Between the combustion valve and the burner, there are two nozzles, one in the middle of the nozzle tube, and the other in the outer ring of the nozzle tube. If you look at it, it may be that the nozzle with fire coming out of the outer ring of the tube is blocked. If your stove is liquefied, the two nozzles in the center of the aperture are repented only, bump and.

Easy to block. You can use a wrench to remove the nozzle and see if the middle is open. After putting it back in, check it for air leaks with an open flame or soapy water.

Kiss, the main reason why the valve can't be opened may be due to the damage of the solenoid valve in the letter fit body, which cannot be sucked. It may also be because the pulse ignition assembly is faulty and cannot be driven normally** solenoid valve, or the voltage is unstable, and the gas valve cannot be opened. The ignition needle dirty kitchen is a very easy to dirty place, especially easy to contaminate the oil, etc., the gas stove is placed for too long, and the ignition needle is easy to be soiled by the oil.

Solution: At this time, you need to clean the grease of the ignition needle and then try to ignite. If you want to ignite the fire, the gas stove has certain requirements for the distance between the ignition needle and the fire cover, and once the distance is deviated too much, the gas stove will not catch fire.

Solution: Generally speaking, the distance between the ignition needle and the fire cover is 4-6mm, and the fire hole should be aligned. The gas stove has a high-voltage line and its joint, and once the high-voltage line is aged, it is easy to make the gas stove not catch fire.

Solution: At this time, only a set of high-voltage protection is required, which should be observed more in ordinary life.

If it is a single pipeline blockage, it is generally a plugging fire hole in the furnace head, which can be penetrated with a thin steel wire; Or disassemble the burner, knock it with metal or grill it with a welding torch to make the impurities and foreign matter inside the burner fall out. I hope the above can help you and I wish you a happy life!

Hello, glad to answer for you. First of all, check the gas source to ensure that the gas source has no arrears for wild travel and whether it is normal. If it is a single pipeline blockage, it is generally the fire hole plugging of the stove head, which can be penetrated with a thin steel wire; Or disassemble the stove head, knock it with metal or use a welding torch to grill the stove head, so that the impurities and foreign substances inside the stove fall out.

I hope the above can help you and I wish you a happy life!

Can you add, I don't quite understand it.

It is also possible that the pipeline has a plug and several plugs, and this problem often appears in the cong bucket, although there is gas, but it can't come out. We need to check the gas outlet valve to see if there is any gas smell, and the reason why it can't catch fire is because the gas is clogged.

Gas stoves are one of the appliances we often use in our homes, and if we don't unplug them, it will be very annoying to us. But don't worry, I'll introduce some solutions below

1.Check that the gas valve is closed first to ensure safe operation.

2.If the stove is cooked, it is recommended to wait for the stove to cool before trying to unplug it.

3.Try spraying foam or lubricant on the surface of the stove and wait a few minutes before trying to pull it off.

4.You can also try gently rotating the burner to loosen it. Try to loosen the burner by inserting a mild tool (such as a rubber hammer, wrench, or proboscis pliers) between the stove and the gas stove, and gently tapping or twisting it to loosen the stove.

5.If none of the above works, it is recommended to have a professional check to ensure that the stove or gas stove is not damaged. Until then, don't force a hard pull.

In conclusion, the occurrence of this can be reduced by using the gas stove correctly and maintaining it in a timely manner. If there is a problem, please pay attention to the safety of the spine and find a professional to solve it in time.

Why does the individual stove of the gas stove not catch fire? Glad to answer for you!!

1. It may be caused by the broken lighter, and the gas source needs to be cut off, or Bi Shi will take out the lighter and replace it with a new one. 2. It may be caused by the wrong position of the ignition needle, once there is too much deviation, there will be no ignition. 3. It is also possible that the micro switch of the gas stove is damaged, in this case, it is not recommended to repair it by yourself, but to find a professional to solve it.

I hope mine is helpful to you and I wish you a happy life.