How to adjust the fire of the gas stove, how to adjust the flame of the gas stove

The correct ignition method of the gas stove: open the valve in front of the stove and press in half a knob first, and then rotate to the left, at this time you will hear the discharge sound of "squeak, squeak" and see blue sparks. Then the natural gas ignited.

When ignition, the switch should be turned on to the maximum, and then gently rotate the knob to the left according to the needs of the fire after ignition, and adjust the size of the flame. A good gas stove with a light blue flame and a strong flame height and size. At the same time, there are a few things to pay attention to when ignition:

1. Open the stove valve to the maximum. At this time, if the inner and outer cone of the flame is not clear, or even yellow, it means that the air volume is not enough, adjust the damper to increase the air inlet volume until the inner and outer cone of the flame is clear and turns light blue.

2. Close the stove valve. If the flame becomes shorter, it means that the air volume is too large, and the valve is slightly smaller.

3. Repeated adjustment, you can get the qualified flame in any state, if the adjustment is not good, it means that the stove has a problem.

Slowly adjust the to adjust the heat and adjust the damper of the stove. Clean the fire hole with a needle, ventilate but not let the wind blow to the gas stove, and increase the angle valve appropriately. Clean the pressure reducing valve nozzles, gas stove nozzles, gas stove pipes.

Turn the switch to the left. Find the main valve in the kitchen first, connect the main valve and the natural gas stove together with a pipe, and then do not turn on the valve switch yet.

Once connected, open the valve, then find the switch on the gas stove and twist it to the left.

If you try many times and still can't ignite, it is likely that the ignition part is faulty, and it is recommended to ask a professional to go to work for repair.

The flame adjustment method of the gas stove is as follows:1. Find that there will be four paddles at the bottom of the gas stove, generally two on the left and two on the right.

2. Dial the paddle at the bottom of the gas stove with your hand, don't move too much, and observe whether the color of the flame has changed while dialing.

After adjusting the flame of the gas stove, it is not normal, it is time to clean the fire outlet, you can take the upper shelf away, take it down and clean it, there are some dirty things in it, you can poke it with a toothpick or wire, and finally put it under the faucet to flush it. After rinsing, wipe off the water stains on the surface with a dry rag and put it back in. Turn on the gas stove and see if it has turned into a normal blue flame.

First of all, for the damper of the gas stove, if the damper is small when adjusting, it will be red, the combustion is not sufficient, the gas is consumed, and the bottom of the pot will produce black spots; The damper is too large and will have difficulty ignition. It should be adjusted to the flame to be blue, and the ignition is not difficult as well.

The burner consists of two parts: the head and the ejector. Its working principle is: the gas flows out of the nozzle at a certain flow rate under a certain pressure, enters the suction contraction tube, and relies on the ejection of the energy of the gas itself to attract the surrounding air into the ejector, which is also called primary air.

The primary air and gas are mixed in the injector, and then flow out through the fire hole of the head for combustion.

In combustion, air is drawn from around the flame to support combustion, and this part of the air is called secondary air. When in use, the volume of induced air is controlled by the air volume regulator (damper). When the flame is de-fired and tempered, the damper opening is reduced to reduce the amount of primary air; When the burner has a yellow flame, the flame is red, and a weak long flame is produced, the opening of the damper is increased.

The damper is directly related to the normal combustion of the gas stove, which shows its importance. No matter what kind of gas cooktop, the damper must be adjusted. Because the damper is too large and the amount of air is too much, the fire is not easy to ignite; If the damper is too small, it is easy to produce red fire and incomplete combustion.

The flame burns best when it is a short, powerful blue flame. For gas stoves with flame-out protection, the damper adjustment ratio is as follows: one damper directly connected to the small stove should be closed as small as possible, and the other damper leading to the outer ring should be opened one-third of the fan surface.

In general, the household gas stove can only fine-tune the air inlet, and under the gas stove, there is a baffle at the air inlet, and the air inlet can be adjusted by turning the angle of the baffle.

The method of adjusting the flame of the gas stove is as follows:

1. The fire power of the gas stove is generally adjusted by the rotary knob of the ignition, the more the knob is twisted to the right, the greater the fire power of the gas stove, and the fire can be adjusted by rotating the ignition knob of the gas stove.

2. Adjust the damper of the gas stove, the damper under the gas stove is divided into one left and one right, the left damper can adjust the flame of the inner ring, and the damper on the right can adjust the flame of the outer ring.

3. The gas main valve can also adjust the fire power of the gas stove, usually only need to rotate the valve of the gas main valve to half to meet the daily use, which is more gas-saving.

1. Open the valve in front of the stove and press in half a knob to press in, and then rotate to the left, at this time, you will hear the discharge sound of "squeak, squeak" and see blue sparks.

2. Open the Jianyan stuffy stove valve to the maximum. At this time, if the inner and outer cone of the flame is not clear, or even yellow, it means that the air volume is not enough, adjust the damper to increase the air intake volume until the inner and outer cone of the flame is clear and turns light blue.

3. Close the stove valve. The damper is generally not adjusted for a small fire. If the flame becomes shorter, it means that the air volume is too large, and the valve is slightly smaller.

4. Repeated adjustment, you can get a suitable flame in any state.

1. Open the valve in front of the stove and press in half the knob first, and then rotate to the left, at this time, you will hear the discharge sound of "squeak, squeak" and see blue sparks.

2. Open the stove valve to the maximum. At this time, if the inner and outer cone of the flame is not clear, or even yellow, it means that the air volume is not enough, adjust the damper to increase the air inlet volume once until the inner and outer cone of the flame is clear, and change the bend to light blue.

3. Close the stove valve. The small fire is like a jujube tomb, and the wind is simple and the rock is stuffy. If the flame becomes shorter, it means that the air volume is too large, and the valve is slightly smaller.

4. Repeated adjustment, you can get a suitable flame in any state.