How to repair an electric kettle if it is broken, and how to repair an electric kettle if it is brok

1.The electric kettle is broken, but the power switch is normal, if the power switch is normal, the fault mostly occurs in the insulation switch. First of all, see whether the reed of the bimetal sheet is pressed against the switch contact rod, if it is pressed too tightly, you can use tweezers to bend it upwards until the distance between the two.

If the distance between the bimetal sheet and the switch lever is normal, the switch box should be disassembled, and the contacts and reeds of the insulation switch should be cleaned and repaired. 2.After powering on, it is not heated, but the indicator light is on, indicating that the power supply has been added to the indicator circuit, and the fault is in the electric heating pipe or its connecting part, and the common electric heating pipe is damaged and the contact is poor.

Remove the electric heating pipe and measure its resistance value. The electric heating pipe is damaged and can generally only be replaced. The poor contact is mainly due to the serious corrosion or deformation of the contact reed in the power plug assembly, which can be disassembled and repaired by the switch box, and it is best to replace it with a new one if the damage is serious.

3.The water cannot boil, and the power cannot be cut off, mainly due to the failure of the reset switch. Common reasons are severe deformation of the thermostat or obstruction of the operation of the switch linkage.

For the former, the convex angle of the small tongue of the thermostat can be rebent to make it push the switch connecting rod normally. For the latter, it is necessary to find the obstructed part or foreign body, which can generally be restored to normal by removing the foreign body and correcting the position. 4.

The common cause of slow heating speed is that the power supply voltage is too low, and the indoor power supply line or plug socket is not in good contact, which should be ruled out first. Then check whether the electric heating pipe is seriously fouled, whether the contact between the base and the power plug holder of the pot body is seriously bad, etc. If the electric heating pipe is fouled, you can scrape it with a knife first, and then polish it with fine sandpaper.

If the contact between the base and the power plug holder of the pot body is seriously poor, you can first remove the oxide layer and dirt of the contact piece and contact of the plug holder, and then correct its shape to make the contact between the two close and good.

Teach you how to fix an electric kettle.

If the electric kettle is broken, it depends on where it is broken, and if the heating plate is broken, there is no need to repair it.

If the temperature fuse is broken, you can replace it with another one.

These can be checked with a multimeter.

Teach you how to fix an electric kettle.

Electric kettle is broken and repaired tips:

1. The indicator light is not lit and water cannot be boiled.

The indicator light does not light up and needs to be checked from two aspects, one is that the power supply cannot be input normally, the natural light of the electric kettle cannot be boiled if the natural light is not on, and there is also a situation that the power supply of the electric kettle has been connected normally, but the thermostat.

There is a problem with the heating plate, such as damage or detachment. Solution: The electric kettle must be connected to the power supply, if the parts are damaged, replace the corresponding parts in time.

2. The indicator light is not lit but can boil water.

If the electric kettle can boil water normally but the indicator light is not on, the indicator light is generally damaged at this time, and the corresponding indicator light parts need to be replaced.

3. The power cannot be cut off after the water is boiled.

Sometimes the water of the electric kettle has been boiled, but it cannot be automatically cut off normally, at this time, you need to check whether the steam switch is damaged in time, the electric kettle has been in a humid environment for a long time, the steam switch is most likely to fail, if you can boil the water but can not cut off the power, you need to repair the steam switch in time.

4. The shell is electrified.

If the case is electrified, it can usually be caused by damage to the power cord or heat generation.

If the disk fails, you can replace it with a new power cord and heating plate.

5. Abnormal sound.

The electric kettle has been used for a long time, and there is more scale inside the kettle, and the sound made by the electric kettle can be different from before, so you need to clean the inner tank of the electric kettle in time to remove the scale.

6. Dry burning without electricity.

Under normal circumstances, the electric kettle has the function of preventing dry boiling, once the electric kettle is dry, it is easy to cause damage to the electric kettle, which will seriously lead to fire. Generally, the reason for the occurrence of dry boiling and uninterrupted power is mainly caused by the failure or damage of the electric kettle, automatic steam switch and thermostat.

The repair steps for common problems in electric kettles are as follows:Material preparation: toothpick, needle, screwdriver, etc. Qi socks.

1. If the electric kettle is not powered on, Song Tsai first looks at the two copper plates of the bottom field boy Wang Pan to see if they are deformed or offset.

2. If it is deformed or offset, use a toothpick needle to adjust the position of the copper sheet so that it can touch the copper ring at the bottom of the electric kettle.

3. If the problem has not been solved, disassemble the base of the electric kettle with a screwdriver.

4. Use a screwdriver to remove the item in the picture below.

5. After removing it, look at the picture below, and polish the electric shock with a needle. Then refill the kettle.

If the electric kettle is broken, you can go to the electronic components accessories store to buy the same specification of the heating pipe, and then carefully replace it. Pay attention to do a good job of insulation and sealing.

Teach you how to fix an electric kettle.

This kind of maintenance of electrical appliances, don't just do it if you don't understand it.

Contact the after-sales service during the warranty period.

Repairs, over-warranty can be delivered to the home.

Electrical repair point consultation repair.

Teach you how to fix an electric kettle.