Many people will ask, why do you need to sprinkle the floor tiles after a few days?

Because it is necessary to avoid the rapid evaporation of cement mortar water, it can better bond the floor tiles tightly, and then play a cooling role.

In this way, it is possible to ensure that the floor tiles will not break, and in general, in this case, there are some fears that there will be some problems, especially according to the surrounding environment and the humidity of the air to make changes.

Because in this way, we can ensure that the tiles are paved more strongly, and it will be better, and it will be more satisfying, and there will be no problems in the later stage.

Because this can keep the floor tiles moist, the floor tiles can be better adsorbed on the ground, and the floor tiles will not be warped and damaged.

Generally, there is no need to sprinkle water after the floor tile is paved, and the sprinkling link should be carried out before the paving of the floor tile, and it is necessary to sprinkle some water on the dry base to make the ground warm and moist, and then the cement is poured into the wet base, which is smoothed and then pasted to the ground. The water sprinkled on the surface of the floor tiles cannot penetrate into the mortar layer under the floor tiles, and if it can, then the quality of the floor tiles is too poor, and it will penetrate the bottom in the future, and it will be even worse if the water leaks into the mortar layer along the gaps in the tiles.

All kinds of bricks know that the uranium surface is waterproof sprinkler to play a role, there is no need for that, the floor tiles are specially scraped with a layer of cement porridge-like slurry when laid, and half of the water can not evaporate when paved, so it is not needed at all after just laying a day"Wellness"。The sand ash used for paving the floor tiles is too dry or the cement ratio concentration is insufficient, and the water will be sprinkled on it before it is completely solidified after paving, and the water will seep from the gap in the floor tiles to the sand and ash cushion under the bottom, and the sand and ash that will be solidified in the future will shrink and sink after encountering water.

When we paste the floor tiles, it can be said that the dry paving method is adopted, and the dry paving method must first sprinkle the floor before pasting the floor tiles, especially in summer and autumn, and sometimes it is necessary to sprinkle water from time to time, because the temperature is high in summer and autumn, and the water evaporation on the ground is large. After the completion of the floor tile paving, it should be sprinkled and maintained in a timely manner, which is required in the building decoration quality acceptance specification. The word given in the specification is timely maintenance, so it is necessary to carry out sprinkling maintenance on the day after the paving of the floor tile.

The operation method must be decided according to the variety of tiles, all-porcelain and marble tiles almost do not absorb water, can be operated directly, glazed tiles imitate tiles, must be soaked with water before pasting, and can be pasted only after eating water. If it is said that it is the 800 * 800 large tiles in the living room, then the large tiles do not need to soak in water before paving, and there is no need to sprinkle water after the paving is completed one day.

The main reason is that the coagulant of the floor tiles has a short setting time in summer, so in order to slow down the setting time, it is necessary to sprinkle water.

In this way, it is necessary to ensure that there are some voids, or some collapse and fragmentation, so it is necessary to sprinkle water after a few days of tiling, which is also very convenient when installing.

Prevent the floor tiles from drying too quickly, causing the bricks to peel off from the cement, and sprinkle water to moisturize, which can slow down the drying speed of the floor tiles and be more conducive to bonding.

This is because the floor tiles need to be dried after they are pasted, and they need to be sprinkled with water after a few days, so you can see the flatness of the floor tiles and the degree of waterproofness.

Because the cement layer will shrink, if it is sprinkled, it will play a protective role to a certain extent, slowing down the shrinkage of the cement.

This is because the floor tiles are sprinkled with water to check the quality of the tiles after being pasted for a few days, and it is also to make the floor tiles stronger.

In this way, the adhesion of the floor tiles can be better, and there will be no stilts or damage, and it will also retain its value.

It is to prevent cracking, prevent falling off, avoid the phenomenon of hollowing of tiles, slow down the shrinkage of cement, and have a better effect.

In order to fix the floor tiles, so that the floor tiles do not move at will, the floor tiles can be fixed in one place without damaging the floor tiles.

Because in this way, the floor tiles can be tightened, and in this way, the floor tiles can be made stronger, and the service life can also be improved.

Doing this for the sake of its quality allows the tile to be more secure.

The purpose is to make it swell a little and see if it will crack, in fact, as long as the tiles are soaked in water before laying the floor tiles, there will be no problems.

It is because through the act of sprinkling water, the brick and cement can be more compatible, so that the tile is more firm, not easy to fall off, not easy to bulge.

Nowadays, the floor tile laying method adopted by the masters is generally dry paving method, the addition of water in this method is very small, can make the floor tile to achieve the purpose of fast drying after laying, this method is currently very popular, there are many benefits, has been widely used, but after paving a few days to sprinkle water on the surface of the floor tile, can play a role in the maintenance of the floor tile. Because after the tile is laid, the cement mortar under the floor tile needs a solidification process, the essence of the cement mortar is inseparable from the participation of water, which is a chemical reaction, only the participation of water, can be tightly attached to the sand, and the ground to form a whole, so only after sprinkling water can the tile and the ground fit more firmly. This avoids the problem of frequent cracking or loosening of floor tiles.

After the floor tiles are laid, be sure not to step on them immediately, which is likely to cause the floor tiles to loosen and deform, and generally have to wait for 48 hours before you can walk on them, and it will take about a week to completely dry. During the period, the surface can be sprinkled with water and cured, and it can be used normally until it is completely firm.

This is because after pasting, it is also necessary to look at the waterproof performance, and it can be seen by sprinkling water whether there is any falling, and if there is a drop, it is also necessary to reapply the latex paint.

This is also to prevent the floor tiles from bulging, if the floor tiles are not sprinkled after being pasted, it is particularly easy to cause dry cracks, and it is also very easy to cause damage to the floor tiles.

After paving the ordinary floor tiles first, there is no need to sprinkle water, and the sprinkler part should be carried out before paving the floor tiles, sprinkle water on the dry base layer to warm the ground, pour cement on the moist foundation to level it, and then stick it on the floor. Floor tiles are patted, and the floor tiles can be evenly glued to the floor. Unless you walk on or step on the freshly laid floor tiles, you are afraid of ruining the leveling effect because the tiles have just been laid.

After the floor tiles are pasted, the purpose of sprinkling water is to make the floor tiles better stick to the floor. It can speed up the protection of floor tiles. This is the case for veteran decorators.

This is because it prevents moisture, and it also has a particularly good maintenance that ensures moisture.

This can avoid some air when sticking the floor tiles, and it also avoids some bad phenomena after the floor tiles are pasted, in this case, you will choose to use more water.

The sprinkling is mainly to make the base of the floor tile better injected, but also to make the tile more conformable, but also to make the cement more solidified, mainly to protect the floor tile.

This keeps the tiles moist all the time, and they can better adsorb to the ground and won't warp.

After the floor tiles are laid, sprinkle water on the surface of the paved tiles to maintain the tiles. After the tiles are laid, the cold mix mortar under the tiles or the adhesive material on the back of the tiles have time to set and reinforce. Their essence is that the cement undergoes some chemical changes, which then tightly binds with the sand and eventually forms a whole that gives the underside of the tile a certain strength.

If the surface of the tile is sprinkled with water in time, it can ensure that the moisture in the tile bonding material will not volatilize. This ensures the normal solidification process of these materials, thus guaranteeing that the bonded material is as strong as it should be, thus preventing the common hollow drum from loosening.

1.Before laying tiles, the color of the tiles must be tested. Check the specifications and specifications to see if there are cracks in the tiles.

The tiles used in the same space should not only ensure that the surface is clean, but also check that the pattern is clear and consistent. Secondly, it is necessary to determine whether the tiles comply with the relevant regulations, and they can only be laid after determining that there are no problems.

2.Before laying tiles, you need to sort them. When sorting tiles, the occurrence of non-whole tiles should be prevented.

If this cannot be avoided, the entire tile needs to be arranged in an inconspicuous place, such as under a cabinet. ground, side walls, etc., and ensure tile symmetry. Congruous.

3.When laying tiles, you also need to check the walls and floors, and pay attention to whether the walls and floors are flat. If the wall and floor are not very flat, the mixed mortar should be wiped to adjust the flatness of the wall and the ground to ensure the flatness of the wall and the ground.

You can't step on it right away. In general, the mixed mortar begins to set after 2 hours, and after 48 hours it is possible to walk on it, but it takes 4 hours to dry completely. 5 days, so after 24 hours, if possible, you can cover with sawdust at room temperature, water and cure for 48 hours.

It cannot be stepped on during the curing period, and can only be stepped on after stabilization.

The cement drying time under the tiles is generally based on the recent weather conditions, generally only 2-3 days in summer to dry, and the tiles need to be sprinkled with water for maintenance after laying the tiles with cement.

It's dry. Need to sprinkle water, how long does it take to sprinkle floor tiles? Generally speaking, cement mortar starts to set after 2 hours, and after 48 hours you can walk on it, but it takes days to dry completely.

This should be determined according to the surrounding environment, it may take more than 10 days, or it may take about half a month, and it is necessary to sprinkle water, so as to avoid hollowing.

The floor tiles can be sprinkled and cured after 24 hours of paving.

Floor tiles need to be sprinkled and cured because of the large volume of concrete, thick cement floor, etc., these large volume of cement, when the heat of hydration is high, and exposed to the air, especially in the high temperature and dry environment, shrink sharply, easy to crack. All cement must be slag Portland cement, (low heat of hydration, slow strength growth in the early stage). This is a structural requirement.

The same is true for the cement used for interior decoration. Whether the wall tiles are pasted firmly or not depends on the treatment of the base wall (according to the actual situation, the moisture content of the base wall is treated.

Flatness, you must not use the mortar pasted with wall tiles to find the vertical error of the base wall or the horizontal direction of the square error.

How long does it take to wash the floor tiles after they have been laid?

Dear, I'm glad to answer for you: Generally speaking, the floor tiles can be drenched after two days, and the general cement mortar will begin to solidify after the completion of the two small banquets, and we will be able to walk around the floor tiles after 48 hours, but the floor tiles should be completely dry, and it will take 4-5 days. The cement mortar begins to solidify 2 hours after the floor tiles are pasted, and the solidification degree can reach 80% after 48 hours.

How long does it take to wash the floor tiles after they have been laid?

Dear, I am glad to answer for you: How long can it be washed after the floor tiles are laid? Answer: Usually the Kai potato boring said that the floor tiles can be drenched after two days, the general cement mortar will begin to solidify after two hours of paving, we will be able to walk around on the floor tiles after 48 hours, but the floor tiles should be completely dry, it takes 4-5 days of hand Zheng time.

Usually after 24 hours of tiling, it can be watered and maintained for 48 hours at normal temperatures.