How to remove the film attached to the glass after aging

If the glass of your home is pasted with plastic film, you can use a hair dryer to blow the film several times with hot air, and when the film is a little hot, you can easily tear it off.

Soak it in hot water, if the glass is relatively large, then soak it in hot water, and after a short period of time, you can tear it with confidence, and if there are many small places, then take a small shovel and take it slowly.

Hair dryer: Soften the glue of the glass sticker with the hot air blown by the hair dryer, scratch it with a card, and finally wipe it clean with a cloth. Wind Oil Essence:

Pour the wind oil essence on the film, and after it penetrates into the film, wipe it back and forth with a dry cloth, and the glass film can be wiped off quickly. Detergent: Pour the dish soap into warm water, dip the mixture with a towel, moisten the glass film, rub it, and then push it with a waste card, and repeat it several times to remove the film.

1. Hair dryer: Soften the glue behind the glass sticker with the help of the heat blown by the hair dryer, scrape with a card while blowing, and finally wipe it clean with a cloth.

2. Wind oil essence: pour the wind oil essence on the film, and after penetrating into the film, wipe it back and forth with a dry cloth, and the glass film can be wiped off quickly.

3. Detergent: Pour the detergent into warm water, dip the mixture with a towel, moisten the glass film, rub it, and then push it with a waste card, and repeat it several times to remove the film.

4. Vinegar: Soak the film with vinegar, scrape off the film with a hard card or ruler board or carving knife, and wipe it clean.

5. Alcohol: Rub alcohol on the film to soften it, and scrub it clean with a rag.

How to tear off the aging glass film of the car. The first method: if the solar film.

If the aging is layered, then the outermost layer can generally be torn directly. But because there is still a layer on top of the glue, it looks like plastic wrap.

Similarly, the adhesive remover cannot enter, so it must be equipped with a shovel so that the adhesive remover can come into contact with the residual glue.

The second method: you can use the baking gun to warm up the glass film first, and then open an opening to it, gently remove the film slowly The speed must be slow, the baking gun continues to heat, so that it is slowly torn, it will not fall off the glue, and then the remaining part continues to heat it, slowly peel down the film, until the whole surface is all knotted.

The third method: if the aging is not too serious, you can use a glue remover and a small blade. The transparent layer should be scraped out with more blades, and then the edges should be pulled.

Otherwise, it is difficult to separate the colored layer from the transparent adhesive layer. Also, if you want to use a glue remover for the backgauge, be careful. Don't scrape too hard, that will break the metal on the glass, so be light when scraping, be careful, don't scrape with metal, and scrape slowly with a plastic scraper will not hurt the ***.

The fourth method: If your car window film is blistered and wrinkled, and then the smell in the car is quite strong, then the car film.

It's time to clean it up. Because the car film may also be the first to smell in the car. Let's tear off the film first, don't lose it, spray the adhesive remover evenly, put the film back again, then go out to catch your breath for five minutes and come back, wrap the scraper with a clean wet towel, and wipe it up and down, left and right repeatedly, so that you can see a brand new glass again.

The last method, similar to the previous ones, is to clean the outside and inside of the windshield, if the car was originally covered with heat insulation film.

You need to tear off the old mulch film first, you can tear a little open, but don't force it to get off, because the film is generally pasted on it for several years is very tight, and forcibly tearing it may cause a large area of glue residue, so you can use the glue remover, while spraying and slowly pulling on the line, so that it will not cause the glue residue to grind, but also quickly tear off the old heat insulation film. If the window film is not good, blistering and wrinkled, then try to replace it as soon as possible, the key is to emit a toxic smell, or it is better to replace it in time.

We must go to a professional 4S shop to tear it off, which will better protect the original paint of the car and will not damage the car.

You can spray some clean stuff on it, these things can corrode some glue, so it is very easy to tear off.

It is recommended to apply adhesive remover to the aging glass film, try not to tear vigorously, you can try to tear more.

Removal methods for aging glass film: wind oil essence removal method, hot towel removal method, hydrogen peroxide removal method, etc.

1. Wind oil essence removal method.

Apply wind oil essence to the plastic sticker, and wipe it off with a dry cloth after a moment of penetration, leaving no traces. If there is no wind oil, it can also be replaced by toothpaste, but the effect is slightly worse.

2. Hot towel removal method.

You can cover it with a hot towel first, and when it is soaked, some of the stickers can be easily removed.

3. Hydrogen peroxide removal method.

Hydrogen peroxide can soften the adhesive that has hardened, and the way to use it is to dip a towel in hydrogen peroxide, wipe the sticker, wipe it a few times, and it can be removed after a minute or so.

Precautions for glass film

1. Do not move the glass within three days after installation, wipe it without water within five days, and do not hang anything on the film glass, causing damage to the film glass.

2. The newly pasted car film is prone to fogging and other conditions, which is a normal phenomenon in the drying process of the solar film. Generally, it is normal for this situation to occur in about a week to half a month, and you only need to wait for it to disappear slowly.

3. After the car is applied, do not use sharp, coarse and hard sharp tools to scrape. Because the car owner does not pay attention to the grinding car, the car film will be scraped with a sharp and hard sharp weapon after the car film, which will greatly reduce the light transmittance of the car film.

You are very happy to serve you and give you the following answers: 1. Reasons for the problem: 1. The glass film is affected by the external environment such as temperature, humidity, and ultraviolet rays, and is easy to age and deteriorate.

2. The glass film is not tightly attached to the window, which is easy to be affected by the external environment, which will also lead to aging and deterioration. 2. Solution and practice steps: 1. First of all, wipe the glass film with a damp cloth to remove dust and dirt, and if there is residual dust, you can wipe it with a wet tissue; 2. Then, use some detergents, such as dish soap, gasoline, Yantai water, etc., to remove the residual dirt, and then wipe it clean with a damp cloth; 3. Next, tear off the glass film from the window, put it in a clean place, and wipe the residue on the glass film with a towel or rag; 4. Finally, put the glass film in a clean place, wash the glass film with water, and then wipe it with a rag to complete the cleaning.

3. Related knowledge: 1. Glass film is a special film, which can effectively reduce indoor ultraviolet radiation, protect the aging of indoor furniture and indoor items, reduce indoor temperature, reduce indoor humidity, and also block external light to make the interior quieter. 2. The glass film should not be cleaned for too long, and regular cleaning can effectively extend the service life of the glass film and prevent the aging and deterioration of the glass film.

1. Wind oil essence removal method: apply wind oil essence on the plastic sticker, and wipe it off with a dry cloth after a moment of penetration, leaving no traces. If there is no wind oil, you can also use toothpaste instead of stove shirt, but the effect is slightly worse.

2. Hot towel removal method: You can cover it with a hot towel first, and when it is soaked, some identification stickers can be easily torn off. 3. Hydrogen peroxide removal method.

Hydrogen peroxide can soften the hardened adhesive, the way to use it is to dip a towel in hydrogen peroxide, wipe the hole sticker, wipe it a few times, and you can remove it after a minute or so. 4. Alcohol removal method: This method is similar to the hydrogen peroxide method, you can use a towel dipped in a small amount of alcohol to wipe the sticker repeatedly, but it must not be sprayed directly on the glass, otherwise the glass will be damaged.

5. For ultra-stubborn stickers, you can go to the market to buy sticker remover, this method is the most thorough and professional.

Hello fiber rent, I am happy to answer for you, the removal method of glass film aging is as follows: 1, you can wet the sticker with dish soap water, and then gently push the glue off with a blade. 2. Blow with a hot air blower, don't open the highest gear and blow on the lowest gear, blow a little and tear a little, don't be in a hurry.

3. Apply some hand cream to the remaining sticker, and then rub it slowly with your hands, you can also rub it off. 4. You can also remove nail polish, nail removal can help remove aging stickers, and the effect is also good.